JIKONG JK-B6A

Contents

JIKONG JK-B6A Smart BMS User Manual

Model: JK-B6A Series

Brand: JIKONG

1. Introduction

The JIKONG JK-B6A Smart Battery Management System (BMS) is designed for large-capacity series lithium battery packs. It offers comprehensive protection and management features, including voltage acquisition, high-current active balancing, overcharge, over-discharge, overcurrent, and over-temperature protection. The BMS also integrates a coulomb meter, Bluetooth communication, and optional GPS and other functions. It is compatible with various battery chemistries such as Lithium Iron Phosphate (LiFePO4), Ternary Lithium, and Lithium Titanate (LTO) batteries.

This protection board utilizes energy transfer active balancing technology, capable of achieving a continuous balance current of up to 0.6A. This high-current active equalization ensures battery consistency, extends battery range, and delays battery aging. The compact design, ease of operation, and full functionality make it suitable for a wide range of applications, including small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage systems, base station backup power supplies, and solar power stations.

JIKONG BMS Active Balance Smart Board with Bluetooth, GPS, RS485/CAN icons
Figure 1.1: JIKONG Active Balance Smart Board highlighting key features like Bluetooth, GPS, and RS485/CAN communication.
Exploded view of JIKONG BMS showing internal circuit board and components
Figure 1.2: Exploded view of the JIKONG BMS, illustrating its internal circuit board and components.

2. Safety Information

Always prioritize safety when working with battery systems. Improper installation or handling of the BMS can lead to serious consequences, including damage to the battery, BMS, or personal injury. Adhere to the following safety guidelines:

  • Ensure all wiring connections are correct and secure before powering on the BMS.
  • Do not short-circuit any terminals or wires.
  • Operate the BMS within its specified voltage and current limits.
  • Avoid exposing the BMS to extreme temperatures, moisture, or corrosive environments.
  • In case of any abnormal behavior, immediately disconnect power and consult the troubleshooting section or a qualified technician.
  • Always wear appropriate personal protective equipment (PPE) when handling batteries and electrical components.
JIKONG BMS protection features: Short Circuit, Over Current, Drop, Over Discharge, Over Temperature, Overcharge
Figure 2.1: Overview of the JIKONG BMS protection features.

3. Package Contents

Upon opening the package, please verify that all the following items are included:

  • JIKONG BMS Protection Board (with Bluetooth function)
  • Temperature Sensor (40cm)
  • Balance Line (4-24S, 75cm length)
  • Power Switch Button
  • Heating Line (included only with BMS models featuring heating function)
JIKONG BMS package contents including BMS board, switch, NTC, and sampling line
Figure 3.1: Typical package contents for the JIKONG BMS.
JIKONG BMS board with connected wires and balance lines
Figure 3.2: JIKONG BMS board with pre-attached wires and balance lines.

4. Specifications

The JIKONG JK-B6A series BMS comes in various configurations. Below are the general specifications and parameters for different current ratings.

4.1 General Specifications

  • Balance Function: Active Balanced BMS
  • Type: Li-ion, LiFePO4, LTO Battery BMS
  • Charge and Discharge Port: Common Port BMS
  • Certification: CE
  • Usage Scenario: Power BMS, Energy Storage BMS
  • Functions: Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
  • Handware or Smart: SMART BMS
  • High-concerned chemical: None

4.2 Product Dimensions

JIKONG BMS dimensions: 162mm length, 102mm width, 20mm thickness
Figure 4.1: Physical dimensions of the JIKONG JK-B6A series BMS.

Dimensions: 162mm (Length) × 102mm (Width) × 20.4mm (Thickness)

Finished Weight: 567g

4.3 Main Parameters by Current Rating

Parameter100A Version120A Version150A Version200A VersionUnit
Supply Voltage20-10020-10020-10020-100V
Operating Power Consumption<800<800<800<800mW
Operating Temperature-30-70-30-70-30-70-30-70°C
Max. Collection Strings24242424String
Max. Balancing Current0.60.60.60.6A
Max. Charging Current100120150200A
Max. Discharge Current100120150200A
Max. Instantaneous Current200240300400A
Max. Internal Loop Resistance0.690.570.390.35mΩ

4.4 Default Parameters

The BMS comes with pre-configured default parameters for various battery types. These can be adjusted via the mobile APP if needed.

ParameterLi-ion (Ternary)LiFePO4LTOUnit
Balancing Initial Voltage332V
Maximum Balancing Current0.60.60.6A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay303030S
Charging Overcurrent Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Release Time606060S
Short-circuit Protection Delay555uS
Charging Overtemperature Protection707070°C
Charging Overtemperature Recovery606060°C
Discharge Overtemperature Protection707070°C
Discharge Overtemperature Recovery606060°C
Charging Low Temperature Protection-20-20-20°C
Charging Low Temperature Recovery-10-10-10°C
MOS Overtemperature Protection100100100°C
MOS Overtemperature Recovery808080°C
Device Address000/

5. Setup and Installation

Careful installation is crucial for the proper functioning and safety of your battery system. Follow these steps precisely.

5.1 Interface Definition

The BMS features various connectors for different functions. Refer to the diagrams below for a detailed understanding of each interface.

Detailed diagram of JIKONG BMS ports including Temperature sensor, CAN/RS485, GPS, LCD, Heat Function
Figure 5.1: Detailed view of the JIKONG BMS ports and their functions.

Key Interfaces:

  • P- and B- Terminals: Main power connections for discharge and battery negative.
  • Balance Port (P1, XH-15AW): Connects to individual cell positive terminals (B1 to B24) and total battery negative (B-).
  • Temperature Interface (P3, XH-4AW): For connecting temperature sensors (T1A, T1B, T2A, T2B).
  • Communication Interface (P4, A1254WF-4A): Supports RS485 (RS485 A, RS485 B) and CAN (CAN H, CAN L) communication.
  • GPS Interface (P5, 1.25T-4PWT): For connecting GPS module (VGPS, TX, RX, GND).
  • Display Screen Interface (P6, A1254WF-6A): For connecting an optional LCD display (VCC for power output).
  • Parallel Interface (P7, A1254WF-3A): For battery parallel function (P-EN, P-status).
  • Alarm Interface (P8, A1254WF-2A): For external alarm output (VCC, GND).
  • ACC Interface (P9, A1254WF-5A): For ACC detection (ACC+, ACC-, C_Detect+, C_Detect-).
  • Heating Wire (D1): For optional heating function (HT-).

5.2 Wiring Diagram

The following diagram illustrates the correct wiring for the JIKONG JK-B6A series BMS for a 24S battery configuration. Ensure all connections are made accurately to prevent damage.

JIKONG BMS 24S wiring diagram showing connections for B+, B-, P-, charger, controller, and balance wires
Figure 5.2: Wiring diagram for the JIKONG JK-B6A BMS in a 24S configuration. This diagram shows connections for the battery total positive (B+), battery total negative (B-), load/charger negative (P-), temperature wires, and individual cell balance wires.

Wiring Steps:

  1. Connect the main negative terminal of the battery pack to the B- terminal on the BMS.
  2. Connect the main positive terminal of the battery pack to the B+ terminal (usually via a separate wire, not directly on the BMS board for high current).
  3. Connect the balance wires from each cell (B1, B2, ..., B24) to the corresponding pins on the balance port (P1) of the BMS. Ensure the order is correct, starting from B1 (first cell positive) up to B24 (last cell positive).
  4. Connect the load and charger negative terminals to the P- terminal on the BMS.
  5. If using the heating function, connect the heating wire to the D1 (HT-) terminal.
  6. Connect the temperature sensors to the P3 interface.
  7. For optional features like GPS, LCD, RS485, or CAN, connect the respective modules to their designated ports (P4, P5, P6).
  8. Before powering on, double-check all connections for correctness and security.

5.3 APP Installation and Device Activation

The JIKONG BMS is controlled and monitored via a mobile application available for Android and iOS devices.

JIKONG BMS Bluetooth Phone App interface showing battery cell voltage, balance status, and parameter modification
Figure 5.3: JIKONG BMS Bluetooth Phone App interface.

APP Installation:

Scan the QR code below to download the official JIKONG BMS mobile application. Android version 7 or higher is required for Android devices.

QR code for JIKONG BMS mobile APP download
Figure 5.4: QR code for downloading the JIKONG BMS mobile APP.

Device Activation:

Before activating the BMS, ensure all balance wires and main power connections (P- and B-) are correctly and securely connected to the battery pack. The BMS does not have a physical power-on switch. It is designed for charging activation mode. To activate the BMS, connect a charger to the battery pack (charger voltage should be at least 2V higher than the battery voltage). The BMS will power on automatically.

Alternatively, if you have an optional display screen and button, you can activate the BMS by connecting the display cable and pressing the button.

6. Operating Instructions

6.1 Active Equalization

The BMS employs active equalization to balance cell voltages by transferring energy from higher-voltage cells to lower-voltage cells. Before using this function, set the basic battery parameters in the APP, including the number of cells, battery capacity, trigger equalization differential pressure (default is 0.01V), and voltage/current calibration.

Users can set the balance trigger pressure difference (mV) in the APP's parameter settings. When active balancing is enabled, it will automatically start if the voltage difference between any two cells exceeds the set value, and stop when the difference falls below the set value. The default balance current is 0.6A. It is recommended that the balance current not exceed 0.2C of the battery capacity. If balancing is not required, it can be turned off in the APP.

Diagram illustrating active equalization process between battery cells
Figure 6.1: Illustration of the active equalization process.

6.2 Protection Functions

The JIKONG BMS provides comprehensive protection for your battery pack. These functions are standard and can be configured via the APP.

  • Charge Overvoltage Protection and Recovery: Prevents overcharging of individual cells. The BMS will stop charging if any cell voltage exceeds the set overvoltage protection value and resume when all cells are below the recovery voltage.
  • Discharge Undervoltage Protection and Recovery: Prevents over-discharging. The BMS will stop discharging if any cell voltage drops below the set undervoltage protection value and resume when all cells are above the recovery voltage. An automatic shutdown voltage is also configurable.
  • Charge Overcurrent Protection and Recovery: Protects against excessive charging current. The BMS will stop charging if the current exceeds the set value for a specified delay and resume after a recovery time.
  • Discharge Overcurrent Protection and Recovery: Protects against excessive discharging current. The BMS will stop discharging if the current exceeds the set value for a specified delay and resume after a recovery time. (Note: Maximum continuous discharge current should not exceed the nominal current of the BMS model).
  • Overtemperature Protection and Recovery: Protects against high temperatures during charge and discharge. The BMS will stop operation if the temperature exceeds the set limit and resume when it falls below the recovery temperature.
  • Low Temperature Protection and Recovery: Protects against low temperatures during charging. The BMS will stop charging if the temperature drops below the set limit and resume when it rises above the recovery temperature.
  • Short Circuit Protection and Recovery: Automatically protects against short circuits. Users can adjust the short circuit protection delay and recovery time via the APP.

6.3 Optional Features

  • Heating Function: (Optional) Prevents battery performance degradation in low-temperature environments. The BMS can activate a resistance heater or heating film. It is recommended to use a normally closed temperature switch (45°C-65°C) in series with the heating circuit for secondary protection.
  • Alarm Function: (Optional) Provides external alerts when the BMS detects safety risks such as overtemperature, overcharge, or over-discharge.
  • Battery Parallel Function: (Optional) Supports parallel connection of battery packs, requiring synchronous use with parallel modules.
  • ACC Detection Function: (Optional) Enables discharge. This can be achieved by applying 12V-70V between ACC+ and ACC- or by short-circuiting them. It also includes a charger detection function (C_Detect+ and C_Detect-).
  • GPS, Display Interface, RS485/CAN Communication: (Optional) The BMS reserves interfaces for GPS modules (for battery location), display screens (for viewing battery information), and RS485/CAN communication modules. These can be selected and configured via the APP.

6.4 Intelligent Sleep

The intelligent sleep function is standard and can be enabled/disabled in the APP. Its purpose is to reduce the BMS's self-consumption by shutting down the protection board when it's in standby (charging/discharging current less than 1A for 26 consecutive hours). The BMS can be reactivated by pressing a button or connecting a charger.

6.5 Parameter Setting

All operational parameters of the JIKONG BMS can be configured through the mobile APP. For detailed instructions on parameter settings, please refer to the "Instructions for Setting Protection Board Parameters" document, which can be downloaded by scanning the QR code provided in the APP Installation section.

7. Maintenance

To ensure the longevity and optimal performance of your JIKONG BMS, follow these maintenance guidelines:

  • Regular Inspection: Periodically check all wiring connections for tightness and signs of corrosion or damage.
  • Cleanliness: Keep the BMS and its surroundings clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
  • Software Updates: Check the JIKONG APP regularly for any firmware updates for the BMS. Keeping the firmware updated ensures optimal performance and access to new features or bug fixes.
  • Environmental Conditions: Ensure the BMS operates within its specified temperature range (-30°C to 70°C) and avoid environments with high humidity or corrosive gases.
  • Battery Health: Monitor your battery pack's health through the APP. Address any cell imbalances or abnormal readings promptly.

8. Troubleshooting

This section provides solutions to common issues you might encounter with your JIKONG BMS.

ProblemPossible CauseSolution
BMS not powering on/activatingIncorrect wiring, charger not connected (for activation), low battery voltage.Verify all wiring (B-, P-, balance wires). Connect a charger with voltage > battery voltage to activate. Check battery voltage.
APP cannot connect to BMS via BluetoothBluetooth not enabled on phone, BMS not powered, APP permissions, distance.Ensure phone Bluetooth is on. Verify BMS is powered. Grant necessary APP permissions. Move closer to the BMS.
Battery cells are unbalancedActive equalization not enabled, incorrect parameters, significant cell degradation.Enable active equalization in the APP. Check balance parameters (trigger voltage, current). Consider individual cell testing if imbalance persists.
Overcurrent/Overvoltage/Undervoltage protection triggers frequentlyParameters set too low/high, faulty sensor, actual overcurrent/voltage.Review and adjust protection parameters in the APP. Verify load/charger current. Check sensor readings for accuracy.
Heating function not workingHeating function not enabled, wiring issue, external temperature switch open.Enable heating in the APP. Check heating wire connections. Verify external temperature switch is closed (if used).

9. User Tips

  • Initial Setup: Always connect the balance wires first, starting from B- and then B1, B2, and so on, up to B+. Connect the main B- and P- last. This sequence helps prevent damage from voltage spikes.
  • APP Customization: Take advantage of the mobile APP to fine-tune protection parameters (e.g., overvoltage, undervoltage, overcurrent) to match your specific battery pack and application requirements.
  • Monitoring: Regularly use the APP to monitor individual cell voltages, temperatures, and overall battery status. This helps in early detection of potential issues.
  • Firmware Updates: Keep an eye out for firmware updates from JIKONG. These often include performance improvements and new features.
  • Cold Weather Operation: If operating in cold climates, consider a BMS model with the heating function to maintain optimal battery performance and lifespan.

10. Warranty and Support

For warranty information and technical support, please contact your seller or refer to the official JIKONG support channels. Ensure you have your product model and purchase details ready when seeking assistance.

A comprehensive user manual in PDF format is available for download, providing more in-depth technical details and instructions. You can access it via the QR code in the APP Installation section or directly at: JIKONG BMS User Manual (PDF).

JIKONG BMS Certificates of Invention and Quality Management System
Figure 10.1: JIKONG BMS Certificates, including Quality Management System and Patent Certificate of Invention.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.