HawkSpeed SpeedyBee Bee35 Meteor LED V2

Contents

SpeedyBee Bee35 Meteor LED V2 Instruction Manual

Enhance your drone experience with vibrant, configurable LED lighting.

1. Product Overview

The SpeedyBee Bee35 Meteor LED V2 is a versatile LED lighting system designed for FPV drones, offering wireless configuration, fantasy color options, and energy-efficient illumination. It includes an LED strip and a BEC module for power and control.

SpeedyBee Meteor LED V2 with BEC module, showing wireless configuration, fantasy colors, bright and energy-efficient features.
SpeedyBee Meteor LED V2 with BEC module and key features.
Close-up of the SpeedyBee BEC module.
Close-up view of the BEC module.

Package Contents

Package contents: Meteor LED Strip + BEC Kit, including wires and screws.
The Meteor LED Strip + BEC Kit includes the LED strip, BEC module, mounting bracket, screws, and connection wires.
  • Meteor LED Strip
  • BEC Module
  • Mounting Bracket
  • Screws
  • Connection Wires

2. Setup and Installation

Follow these steps for proper installation and initial setup of your SpeedyBee Bee35 Meteor LED V2.

2.1 Power Connection

The LED strip requires a simple two-wire power connection to your flight controller (FC).

Installation instructions for power wiring (V to FC BAT, G to GND).
Wiring diagram for power connection.
  1. Solder the 'V' wire from the BEC module to the 'FC BAT' pad on your flight controller.
  2. Solder the 'G' wire from the BEC module to the 'GND' pad on your flight controller.

2.2 Wireless Flight Controller Configuration

For wireless configuration capabilities, connect the BEC module to your flight controller's UART ports. Flight controllers with built-in Bluetooth may not require TX/RX connections.

Installation instructions for wireless flight controller configuration (T to FC RX, R to FC TX).
Wiring diagram for wireless flight controller configuration.
  1. Connect the 'T' wire from the BEC module to the Flight Controller's RX pad (e.g., RX1).
  2. Connect the 'R' wire from the BEC module to the Flight Controller's TX pad (e.g., TX1).

Important: MSP (Multiwii Serial Protocol) for the relevant UART (e.g., UART1) must be enabled in your flight controller's software configuration.

2.3 App Requirements

To utilize the full wireless configuration features, ensure your mobile device meets the following app version requirements:

  • Android: Version 2.2.5 or above
  • iOS: Version 1.8.17 or above
Overview image of SpeedyBee Bee35 Meteor LED V2 features and app requirements.
Key features and app version requirements.

3. Operation

The Meteor LED V2 offers various functionalities for controlling your drone's lighting.

3.1 Power On/Off and Effect Switching

The BEC module features a button for basic control:

  • Press the button to power the LED strip on or off.
  • Press the button to cycle through different LED effects.

3.2 Wireless Configuration

Use the SpeedyBee app on your smartphone to wirelessly configure the LED strip and flight controller settings. This allows for advanced customization of colors, patterns, and other parameters.

Drone with Meteor LED V2 strip illuminated in blue.
Drone illuminated with blue Meteor LED V2 strip.
Drone with Meteor LED V2 strip illuminated in multiple colors.
Drone illuminated with multi-color Meteor LED V2 strip.
Image showing various LED color effects on a drone and a note about splicing.
The actual LED effects may vary slightly from visual representations.

4. Maintenance

The SpeedyBee Bee35 Meteor LED V2 is designed for durability. Regular maintenance is minimal but important for longevity.

  • Keep the LED strip and BEC module clean and free from dust or debris.
  • Avoid exposing the components to excessive moisture or extreme temperatures.
  • Periodically check solder joints for secure connections.

5. Troubleshooting

5.1 Entering DFU Mode for Firmware Updates

If you need to update the firmware of your flight controller using the BEC module, follow these steps:

Instructions for entering DFU mode using the BEC module button and connecting to Flight Controller BOOT.
DFU mode connection diagram.
  1. Press and hold the button on the BEC module.
  2. While holding the button, power up your drone.
  3. Plug in the USB cable to your flight controller. This should put the flight controller into DFU (Device Firmware Upgrade) mode.

Note: This method only supports flight controllers with a BOOT solder pad, such as the SpeedyBee F4mini flight controller. Connect the 'B' wire from the BEC module to the Flight Controller's BOOT pad.

BOOT Key Initiation diagram for DFU mode, showing the BEC module and Betaflight configurator.
BOOT Key Initiation process for DFU mode.

5.2 Connectivity Issues

  • Ensure all solder connections are secure and correct as per the installation diagrams.
  • Verify that MSP is enabled for the UART port used for wireless configuration in your flight controller software (e.g., Betaflight).
  • If using a flight controller with Bluetooth, TX/RX connections might not be necessary for basic wireless configuration.

6. Specifications

Specifications table for BEC Module and Meteor LED.
Detailed specifications for the BEC Module and Meteor LED.

BEC Module

AttributeValue
Input Voltage7.4V-25.2V
Output Voltage4.0V-4.5V
Operating CurrentMax ~2A (5V)
BluetoothSupported
WiFiSupported (activated automatically only when updating firmware)
Communication InterfaceSerial (UART)
Baudrate115200
Power IndicatorRed light (stays on when powered)
Button FunctionPower on/off, switch effects
Dimensions23 x 15 x 6.3 mm (excluding screws and fittings)
Weight2g

Meteor LED Strip

AttributeValue
Suitable for ModelSpeedyBee BEE35
Number of LEDs126
Adhesive BackingYes
Input Voltage4.0V-4.5V
Operating CurrentMax ~1.7A (5V)
Dimensions785 x 5 x 2 mm
Weight10.5g

Package Dimensions

AttributeValue
Length16 cm
Width14 cm
Height1 cm
Weight0.033 kg

7. User Tips

  • Compatibility: The Meteor LED V2 has been successfully used with other SpeedyBee models, such as the Bee 25, indicating potential broader compatibility beyond the Bee35.
  • Customization: The LED strip's length can be adjusted by splicing to fit different drone frames or desired lighting configurations without affecting normal functionality.
  • Initial Inspection: Always check the product and packaging upon arrival to ensure all components are present and in good condition.

8. Warranty and Support

For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty-related inquiries.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.