Flipsky 65161

Contents

Flipsky 65161 Brushless Motor Instruction Manual

Model: 65161

1. Introduction

The Flipsky 65161 is a high-performance, sensorless brushless motor designed for demanding applications, particularly efoils and other amphibious electric vehicles. It features robust construction with an IP68 waterproof rating, ensuring reliable operation in wet environments. This manual provides essential information for the safe and effective setup, operation, and maintenance of your Flipsky 65161 motor.

Flipsky 65161 motor with propeller and shroud components.
Flipsky 65161 motor with propeller and shroud components. This image illustrates the motor, propeller, and propeller shroud, which may be included depending on the purchased variant.

2. Safety Information

  • High Voltage/Current: This motor operates at high voltages and currents. Always disconnect power before handling or making any connections. Improper handling can result in severe injury or death.
  • Waterproofing: While IP68 rated, ensure all connections are properly sealed and the motor housing is intact before submerging. Do not operate if there is any visible damage to the motor or wiring.
  • Rotating Parts: Keep hands, hair, loose clothing, and other objects clear of the propeller and rotating shaft during operation to prevent injury.
  • Overheating: Monitor motor temperature during initial runs. Excessive heat can damage the motor and other components. Ensure adequate cooling.
  • Proper Installation: Securely mount the motor to prevent movement or detachment during operation. Use appropriate fasteners and follow mounting guidelines.

3. Specifications

FeatureSpecification
Voltage6-20S (25.2-84V)
Max Spin Speed (RPM)16380
KV (RPM/V)120KV / 100KV
Rated Power3000W
Max Power6000W
Rated Current60A
Peak Current200A
Rated Torque6.3 N·m
Max Torque at 60%9 N·m
DimensionsD65*L161mm
Max Working Temperature120°C
Insulation Voltage & Leak CurrentAC 500V / 1mA / 3s
Lead Wires Extension8AWG × 1300mm
Waterproof LevelIP68
Weight3kg
Plug8.0mm bullet plug
Motor Wires3 × 8AWG (6.5mm)
Resistance58mΩ
ShaftØ12 -0.005/-0.01mm
Number of Slots & Poles18N / 6P (Set as 3 pairs for ESC setup)
Inductance170μH

4. Package Contents

Your Flipsky 65161 motor package typically includes:

  • Flipsky 65161 Brushless Motor (100KV or 120KV variant)
  • Propeller (may vary based on selected option, e.g., 'A set' includes propeller)
  • Propeller Shroud/Duct (if part of the selected option)
  • Mounting Screws

5. Setup

5.1 Motor Mounting

Mount the motor securely to your efoil board or other application using appropriate fasteners. Refer to the dimension diagrams below for precise measurements and mounting hole patterns. Ensure the motor is aligned correctly to prevent unnecessary strain on the shaft and bearings.

Technical drawing showing dimensions for Flipsky 65161 motor with 12mm round threaded shaft.
Technical drawing showing dimensions for Flipsky 65161 motor with 12mm round threaded shaft. Note the M4 screw holes and shaft dimensions.
Technical drawing showing dimensions for Flipsky 65161 motor with 12mm splined shaft.
Technical drawing showing dimensions for Flipsky 65161 motor with 12mm splined shaft. Note the 8.0mm bullet connectors and M4 mounting holes.

5.2 Electrical Connections

  • ESC Connection: Connect the three 8AWG motor wires to your Electronic Speed Controller (ESC) using the 8.0mm bullet plugs. Ensure a secure and correct phase connection.
  • Battery Connection: Connect your ESC to a compatible battery pack (6-20S, 25.2-84V). Always use connectors rated for the high current draw of this motor.
  • ESC Configuration: Configure your ESC according to its manufacturer's instructions. For this motor, set the number of pole pairs to 3 (corresponding to 18N/6P).
Flipsky 65161 motor showing long lead wires and 8.0mm bullet connectors.
Flipsky 65161 motor showing long lead wires and 8.0mm bullet connectors for connection to an ESC.

5.3 Propeller Installation (if applicable)

If your motor comes with a propeller or you are installing one, ensure it is correctly aligned and securely fastened to the shaft. For threaded shafts, use the provided nut and washer. For splined shafts, ensure the propeller hub matches the spline pattern and is secured with any retaining mechanisms.

Flipsky 65161 motor with round threaded shaft.
Flipsky 65161 motor with a round threaded shaft, ready for propeller attachment.

6. Operating Instructions

  • Pre-Operation Check: Before each use, inspect the motor, wiring, and propeller for any damage or loose connections. Ensure the motor is clean and free of debris.
  • Initial Power-Up: Power on your ESC and remote control (if applicable) according to their respective manuals. Perform a low-power test to ensure the motor spins smoothly and in the correct direction.
  • Temperature Monitoring: During operation, especially during initial runs or under heavy load, monitor the motor's temperature. The maximum working temperature is 120°C. If the motor becomes excessively hot, reduce load or stop operation to allow it to cool.
  • Amphibious Use: The IP68 rating allows for submersion. However, avoid prolonged exposure to highly corrosive liquids or extreme pressures beyond its design limits.

7. Maintenance

  • Cleaning: After each use, especially in saltwater, rinse the motor with fresh water to remove salt and debris. Allow it to dry completely before storage.
  • Inspection: Regularly inspect the motor housing for cracks, the shaft for bends, and the wires for fraying or damage. Check bullet connectors for corrosion or looseness.
  • Bearing Check: Periodically check the motor bearings for smooth rotation. If you notice grinding or excessive play, consider professional servicing.
  • Storage: Store the motor in a dry, cool place away from direct sunlight and corrosive materials.

8. Troubleshooting

  • Motor Not Spinning:
    • Check all electrical connections between the motor, ESC, and battery.
    • Verify the battery is charged and providing sufficient voltage.
    • Ensure the ESC is properly calibrated and receiving a signal from your controller.
    • Confirm the ESC is compatible with sensorless brushless motors and configured for 3 pole pairs (18N/6P).
  • Motor Overheating:
    • Reduce the load on the motor.
    • Check for any obstructions around the motor that might impede cooling.
    • Ensure the propeller is not damaged or causing excessive drag.
    • Verify ESC settings are appropriate for the motor.
  • Loss of Power/Intermittent Operation:
    • Inspect all wiring and connectors for corrosion, damage, or loose connections.
    • Check battery health and discharge rate.
    • Ensure the ESC is not entering thermal shutdown due to overheating.

9. User Tips

  • ESC Compatibility: When selecting an Electronic Speed Controller (ESC), ensure it is rated for the motor's voltage (6-20S) and peak current (200A). It must also be compatible with sensorless brushless motors and allow for configuration of pole pairs (set to 3 for this motor).
  • Shaft Type: The motor is available with either a 12mm round threaded shaft or a 12mm splined shaft. Choose the variant that is compatible with your propeller and mounting system.
  • Propeller Selection: Experiment with different propeller sizes and pitches to find the optimal balance of thrust and efficiency for your specific application.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims. Always refer to the official Flipsky website or your point of purchase for the most up-to-date support information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.