LAUNCH CRT5011 V2

Contents

LAUNCH Creader TPMS 5011 V2 User Manual

Comprehensive instructions for operation, maintenance, and troubleshooting.

1. Product Overview

The LAUNCH Creader TPMS 5011 V2 is a 3-in-1 TPMS service tool designed for mechanics and DIY enthusiasts. It offers comprehensive TPMS diagnostics, sensor activation, reading, learning, and programming. Additionally, it supports full OBDII/EOBD functions and 12 essential reset functions for vehicle maintenance.

LAUNCH Creader TPMS 5011 V2 device and its main TPMS functions

Image: LAUNCH Creader TPMS 5011 V2 device displaying its main TPMS functions, including support for 315/433MHz sensors, 99% vehicle coverage, sensor check, activation, diagnosis, relearn, OE number check, read/write sensor ID, and turning off TPMS warning light. It also supports 11 languages.

Video: Overview of the LAUNCH Creader TPMS 5011 V2's capabilities, demonstrating its use in TPMS functions and OBD-II diagnostics.

2. Getting Started

2.1 Package Contents

The package for your LAUNCH Creader TPMS 5011 V2 typically includes:

  • LAUNCH Creader TPMS 5011 V2 device
  • OBD-II connection cable
  • Type-C charging cable
  • Quick Start Guide
Package contents of LAUNCH Creader TPMS 5011 V2

Image: Contents of the LAUNCH Creader TPMS 5011 V2 package, showing the device, OBD-II cable, Type-C charging cable, and Quick Start Guide.

2.2 Device Specifications

FeatureSpecification
Display Screen5-inch Touch-screen (720*1280 Pixels)
Operating SystemAndroid 8.1
Battery6000mAh
Memory2GB RAM + 32GB Storage
Connectivity2.4G WiFi
Input Voltage9-18V
Languages Supported11 languages

Note: The device supports free lifetime updates via WiFi.

2.3 Initial Setup and Charging

  1. Charge the Device: Connect the device to a power source using the provided Type-C charging cable. Ensure the battery is sufficiently charged before first use.
  2. Power On: Press and hold the power button to turn on the device.
  3. Language Selection: Follow the on-screen prompts to select your preferred language.
  4. Wi-Fi Connection: Connect the device to a stable 2.4G Wi-Fi network for updates and online functions.

3. Operating Instructions

3.1 TPMS Functions

The LAUNCH Creader TPMS 5011 V2 provides comprehensive functions for Tire Pressure Monitoring Systems.

LAUNCH Creader TPMS 5011 V2 main screen showing TPMS functions

Image: Main screen of the TPMS 5011 V2, highlighting the TPMS, Reset, OE Inquiry, OBD II, Upgrade, Data, and Settings options.

3.1.1 Activate TPMS Sensors

This function allows you to activate 315MHz and 433MHz TPMS sensors to view sensor data.

  1. Select "TPMS" from the main menu.
  2. Choose "Activate" mode.
  3. Hold the tool near the tire valve stem to activate the sensor.
  4. The device will display sensor data such as Tire Temperature, Tire Pressure, Battery Condition, and Sensor ID.
Activating TPMS sensors with LAUNCH Creader TPMS 5011 V2

Image: Illustration of activating a TPMS sensor using the device, showing the display of tire temperature, tire pressure, battery condition, and sensor ID.

3.1.2 TPMS Programming (for LAUNCH LTR-03 and other unencrypted sensors)

This function allows you to program new sensor IDs into LAUNCH LTR-03 sensors or other unencrypted sensors.

  • Auto Create: Generates a new ID that matches your vehicle and programs it into a new LAUNCH sensor.
  • Manual Create: Allows manual input of a sensor ID (random or original).
  • Copy ID by Activation: Writes the retrieved original sensor data (after activation) to a new LAUNCH sensor.
  • Copy by OBD: Reads the sensor ID from the vehicle's ECU via the OBD port and programs it into a new sensor.

Note: This function is only available for LAUNCH LTR-03 sensors and other unencrypted sensors. The device supports unlimited repeated programming and can program up to 8 LAUNCH sensors simultaneously.

Programming TPMS sensors with LAUNCH Creader TPMS 5011 V2

Image: Detailed view of the TPMS programming interface, showing options for Auto Create, Manual Create, Copy ID by Activation, and Copy by OBD. A note indicates compatibility with LAUNCH and other unencrypted sensors.

3.1.3 TPMS Relearn

After replacing or programming new sensors, the relearn function registers the new sensor IDs with the vehicle's ECU.

  • OBD Relearn: Writes TPMS sensor IDs to the TPMS module via the OBD connector.
  • Automatic Relearn: The vehicle automatically learns new sensor IDs during a drive cycle.
  • Stationary Relearn: Requires the vehicle to be in a specific mode (often with a TPMS tool) to learn new sensor IDs.

You can also check the OE (Original Equipment) number of the original sensor.

3.1.4 TPMS Diagnostics

Perform a comprehensive scan of the TPMS system to quickly and precisely grasp tire health status.

  • Read and erase TPMS error codes (DTCs).
  • Display TPMS live data in graphical form.
  • Access TPMS ECU information.
  • Turn off the TPMS malfunction warning light.
TPMS Diagnosis and warning light reset with LAUNCH Creader TPMS 5011 V2

Image: Display showing TPMS diagnosis, including reading TPMS warning lights and DTCs, and the option to clear TPMS DTCs.

3.2 OBD-II Full-Function Diagnosis

The device provides complete OBDII diagnostic functions for engine systems of OBDII-compliant vehicles.

  • Reading Codes: Displays detailed descriptions of Diagnostic Trouble Codes (DTCs).
  • Erasing Codes & Reset: Turns off Check Engine Lights (MILs), clears codes, and resets monitors.
  • Data Stream: Reads and displays live ECU/PCM data stream, plots functions graphically, and stores freeze frame data.
  • I/M Readiness Status: Shows whether various emissions-related systems are operating properly and ready for inspection.
  • Read Live Data Stream: Displays continuous data stream from a vehicle in live graphic (waveform) display.
  • View Freeze Frame Data: Checks vehicle conditions recorded by the on-board computer when an emission-related fault occurs.
  • O2 Sensor Test: Retrieves and views O2 sensor monitor test results.
  • On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
  • Read Vehicle Information: Displays VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).
  • Component Test: Actuates certain vehicle components via commands from the scanner to test their operability.

3.3 12 Reset Functions

The LAUNCH Creader TPMS 5011 V2 is equipped with 12 commonly used maintenance reset functions:

12 Reset Functions available on LAUNCH Creader TPMS 5011 V2

Image: Overview of the 12 reset functions: SAS Reset, Brake Reset, Oil Reset, I-M-M-O Reset, Inject Reset, Battery Matching, ABS Bleeding, Throttle Reset, DPF Reset, Sunroof Reset, Seats Calibration, and Windows Calibration.

  • SAS Reset: Calibrates the steering angle position sensor after replacement or repair.
  • Brake Reset: Resets the brake pad indicator light after replacing brake pads.
  • Oil Reset: Resets the oil life system after an oil and filter change.
  • I-M-M-O Reset (Immobilizer Reset): Resets immobilizer data.
  • Inject Reset (Injector Coding): Codes new fuel injector numbers after installation.
  • Battery Matching (Battery Reset): Resets the car battery monitoring unit after battery replacement.
  • ABS Bleeding: Bleeds the brake system to restore ABS braking sensitivity.
  • Throttle Reset: Initializes the throttle actuator to its default state.
  • DPF Reset (DPF Regeneration): Clears particulate matter from the DPF filter.
  • Sunroof Reset: Resets sunroof functions, including closing on rainy days, slide/tilt memory, and outside temperature threshold.
  • Seats Calibration: Calibrates memory in replaced or repaired seats.
  • Windows Calibration: Performs door window matching to recover ECU initial memory.

4. Maintenance and Updates

4.1 Software Updates

The LAUNCH Creader TPMS 5011 V2 supports lifetime free software updates via Wi-Fi. To update:

  1. Ensure the device is connected to a stable 2.4G Wi-Fi network.
  2. From the main menu, select "Upgrade".
  3. Follow the on-screen instructions to download and install the latest software updates.

4.2 Battery Care

The device is equipped with a 6000mAh battery. To prolong battery life:

  • Charge the device regularly, avoiding complete discharge.
  • Store the device in a cool, dry place when not in use.
  • Avoid exposing the device to extreme temperatures.

5. Troubleshooting

If you encounter issues with your LAUNCH Creader TPMS 5011 V2, refer to the following common troubleshooting steps:

  • Device not powering on: Ensure the battery is charged. Connect to the Type-C charging cable and try again.
  • Unable to connect to Wi-Fi: Check your Wi-Fi network settings and ensure the device is within range of a 2.4G network.
  • Sensor activation failure: Ensure the tool is held correctly near the tire valve stem. Verify the sensor type (315/433MHz) is supported.
  • TPMS programming issues: Confirm you are using LAUNCH LTR-03 sensors or other unencrypted sensors. Ensure the sensor is properly placed for programming.
  • OBD-II connection problems: Check the OBD-II cable connection to both the device and the vehicle's OBD port. Ensure the vehicle's ignition is on.
  • Software update failure: Ensure a stable internet connection during the update process. Do not power off the device during an update.

For more complex issues, refer to the "Warranty and Support" section for assistance.

6. User Tips

  • Always ensure the device's software is up-to-date for optimal performance and the latest vehicle coverage.
  • When performing TPMS functions, work on one wheel at a time to avoid confusion and ensure accurate readings.
  • For programming, consider using LAUNCH LTR-03 sensors for guaranteed compatibility and performance.
  • Keep the Quick Start Guide handy for quick reference during initial operations.

7. Warranty and Support

The LAUNCH Creader TPMS 5011 V2 comes with a 2-year warranty. For any post-sales issues, technical instruction, or support, please contact the manufacturer or your vendor. A team of professionals is available for 7*24 technical support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.