1. Introduction
The X100MAX 2 Smart Diagnostic System is a professional scan tool for vehicle diagnostics, based on the Android operating system. It supports multi-language switching and is suitable for different countries and regions.
Please read this user manual carefully before using the Smart Diagnostic System, referred to as the "Scan Tool" throughout this document. When reading the manual, please pay attention to the words "Note" or “Caution”, and read them carefully for appropriate operation.
2. Product Overview
2.1 Tablet Components
The X100 MAX2 tablet features a robust design for professional use.

Image: XTOOL X100 MAX2 Tablet and VCI Box, highlighting J2534, Topology Mapping, ECU Coding, and 42+ Reset functions.
Key components include:
- Type-C Port: For charging and data transfer.
- Reset Hole: To reset the device if needed.
- Power Button: To turn the tablet on/off.
- Microphone: For voice input.
- Camera: For capturing images.
- Speaker: For audio output.
- Nameplate: Contains product identification.
- Tablet Holder: For convenient positioning.
2.2 VCI Box Components
The VCI (Vehicle Communication Interface) Box is essential for vehicle communication.

Image: XTOOL VCI Box, illustrating wireless and wired communication capabilities.
Key components include:
- Screen: Displays status information.
- DB15 Port: For main cable connection.
- Nameplate: Contains product identification.
- USB Type-B Port: For PC connection.
3. Setup: Vehicle Connection
Two connection methods are available: wireless and wired.

Image: Diagram showing the connection of the X100 MAX2 tablet and VCI box to a vehicle for diagnosis.
- Press and hold the Power button to turn on the tablet.
- Select App language and start the activation.
- Follow the hints to complete the activation.
- Connect the DB15 connector of the main cable to the VCI box.
- Plug the OBDII-16 connector of the main cable into the vehicle's DLC port.
- When the VCI box gets powered on, the tablet will automatically search for it and make a WiFi connection.
- Your tablet is now ready for use.
3.1 Precautions for Diagnosis
- The voltage range on the car: +9~+36V DC.
- When testing some special functions, the operator must operate according to the prompts and meet the test conditions. For some models [special functions], the conditions that need to be met are: engine water temperature 80 °C~105 °C, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.
- The electronic control systems of different models are very complicated. If you encounter situations where it is impossible to test or a large amount of test data is abnormal, you can search for the ECU of the vehicle and select the menu for the model on the ECU nameplate.
- If the vehicle type or electronic control system to be tested is not found in the diagnostic function, please upgrade the vehicle diagnostic software to the latest version using the Updates menu or consult the XTOOL technical service department.
- Only wiring harnesses provided by XTOOL and designed for the device are permitted to be used with this device to avoid damage to the vehicle or the device.
- When running a Diagnostics function, it is forbidden to shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.
4. Operating Instructions
4.1 General Operation Instructions
- Keep the device away from heat or fumes when in use.
- If the vehicle battery contains acid, please keep your hands and skin or fire sources away from the battery during testing.
- The exhaust gas of the vehicle contains harmful chemicals. Please ensure adequate ventilation.
- Do not touch the vehicle cooling system components or exhaust manifolds when the engine is running due to the high temperatures reached.
- Make sure the car is securely parked, Neutral is selected or the selector is at the P or N position to prevent the vehicle from moving when the engine starts.
- Make sure the (DLC) Diagnostic Link Connector is functioning properly before starting the test to avoid damage to the Diagnostic Computer.
- Do not switch off the power or unplug the connectors during testing.
- Doing so may damage the ECU (Electronic Control Unit) and/or the Diagnostic Computer.
4.2 Diagnostics
The diagnostic function can read ECU information, read and clear DTC (Diagnostic Trouble Codes) and check live data and freeze frame data. The Diagnostic application can access the ECU of various vehicle control systems, including the Engine, Transmission, Anti-lock Braking System (ABS), Airbag Safety Restraining System (SRS), Electronic Parking Brake system (EPB) and perform many types of actuation tests.
4.2.1 Vehicle Selection
The Scan Tool supports the following 3 ways to access the smart diagnostics system:
- AUTO SCAN: It supports the automatic reading of vehicle VIN code. You can also tap on the button “AUTO SCAN” on the diagnosis system entrance to use this function. Please make sure that the car and the device are well connected before using this function.
- MANUAL INPUT: It supports manual input of car VIN code. When entering the VIN code manually, make sure that the 17 characters entered are correct to ensure accurate test results.
- SELECT VEHICLE BY AREA: You can choose a car brand by selecting the appropriate region at the top of the screen. You can select the vehicle model that needs to be diagnosed according to the area.
Note: If your model is not recognized, please try the following steps:
- UPDATE all software, and check whether the APP is updated in [Settings].
- Click Diagnosis on the main menu to enter the selection menu, manually select the engine system to read the ECU information, and confirm whether the VIN can be read.
- Contact the XTOOL technical team to provide the VIN code to confirm whether the model supports automatic identification of VIN.
4.2.2 Diagnosis Functions
Diagnostics functions supported by the Scan Tool are listed below:
- Read ECU Information
- Read/Clear Trouble Code
- Read Live Data
- Actuation Test (Bi-Directional Control)
Read ECU Information
This function is to read ECU version information and is the equivalent of "System Identification" or "System Information” in some electronic control systems. These equivalent terms all refer to reading ECU-related software and hardware versions, models and production date of diesel engines, part numbers, etc. This information is helpful when recording maintenance records and ordering new parts.
Read Trouble Code
In the process of diagnosis, if the device shows “System is OK” or “No Trouble Code", it means there is no related trouble code stored in ECU or some troubles are not under the control of ECU. Most troubles are mechanical system troubles or executive circuit troubles. It is also possible that the signal of a sensor may be inaccurate but within limits, which can be examined using Live Data.
Clear Trouble Code
It allows for clearing current and historical trouble codes stored in the ECU memory, under the premise that all the troubles have been resolved.
Read Live Data
Real-time information about various sensors is called "Live Data". Live Data includes parameter identifications (PIDs) of the running engine such as oil pressure, temperature, engine speed, fuel oil temperature, coolant temperature, intake air temperature, etc. Based on these parameters, we can predict directly where the problem lies, which helps to narrow the scope of maintenance. For some vehicles, during their actual operation, the problems such as performance characteristics or sensitivity reduction, can be evaluated using live data.
Actuation Test (Bi-directional control)
Actuation test, also known as bidirectional control, is a generic term used to describe sending and receiving information between one device and another. This function is used mainly to judge whether these actuating components of the engine are working properly.
4.3 Special Functions
The X100 MAX2 supports a lot of commonly used special reset functions, allowing you to quickly access your vehicle system for various scheduled services, maintenance, and reset performance. These functions often eliminate the need to reset codes after resolving common problems. Since XTOOL is continuously developing, the manual may not include all of the latest special functions that are available for download. This user manual lists some of the commonly used special reset services for your reference.

Image: Overview of 42+ Hot Use Maintenance Services available with the X100 MAX2.
4.3.1 ABS Bleeding
Anti-Lock Braking System keeps the tires from locking up immediately when there are brakes. Keeping ABS in good condition can give full play to the effectiveness of the brakes, shorten the braking time and distance, prevent the vehicle from skidding and tailing during emergency braking, ensure good driving stability and steering maneuverability, and avoid violent friction between the tires and the ground to reduce tire wear. When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.
ABS Bleeding can be performed in the following cases:
- Replace the rear brake distributor pump or the front brake distributor pump.
- Severe brake fluid shortage.
- Change the brake fluid.
The operation guidelines of the ABS Bleeding function are shown as below:
- Read the operating instructions and precautions that appear on the screen carefully before performing the operation to ensure that the equipment and car are in the correct condition.
- Attach bleeder bottle to the left rear bleeder screw.
- Open the left rear bleeder screw.
- When ready, click "OK" to enter the bleed procedure, and pump the brake pedal continuously with steady applies every 2 seconds during the entire procedure.
- Continue pumping the brake pedal; when air bubbles are no longer visible, select "OK" to enter the next bleed procedure for the left front wheel.
- Repeat the operation 3 times to complete the bleed procedure for the left front wheel, right front wheel and right rear wheel in turn.
- Stop pumping the brake pedal, and close the right rear bleeder screw.
- Click "OK" to complete the entire bleed procedure.
Caution:
- The ABS pump screw needs to be unscrewed.
- Brake fluid will be under pressure during this process. Secure the bleed hose and open bleeder screws slowly.
- Some vehicles do not support automatic bleeding, but manually bleeding.
4.3.2 Oil Reset
The Scan Tool can be used to reset the engine oil life system, which calculates the optimum oil life change interval based on the vehicle's driving conditions and climate. The oil life reminder must be reset each time the oil is changed so that the system can calculate when the next oil change is required.
This function can be performed in the following cases:
- If the service lamp is on, you must provide service for the car. After service, you need to reset the driving mileage or driving time so that the service lamp turns off and the system enables the new service cycle.
- After changing engine oil or electric appliances that monitor oil life, you need to reset the service lamp.
The operation guidelines of the Oil Reset function are shown as below:
- Enter the Oil Reset menu and choose relevant models according to the vehicle being tested.
- Follow the instructions displayed that are specific to the vehicle and press OK after completing the instructions shown.
- Enter Maintenance mileage reset menu.
- Click INPUT and enter a reasonable value of remaining oil life and press OK.
- Confirm the [New Value] you just entered, and then click OK at the bottom right to complete the procedure.
- Message of 'Write successfully' displays when Oil Reset function has successfully performed.
4.3.3 EPB (Electronic Parking Brake)
Electronic Parking Brake (EPB) System reset is a popular special function. You can use this function to reset the electronic parking brake system and brake pads (retraction, release of the brake pump), G-sensor and body angle calibration. This function has multiple uses and can safely and effectively maintain the electronic brake system. These applications include deactivating and activating brake control systems, assisting in controlling brake fluid, applying and releasing brake pads, setting brakes after replacing brake discs or brake pads, etc.
A reset must be performed in the following cases:
- The brake pad and brake pad wear sensor are replaced.
- The brake pad indicator lamp is on.
- The brake pad sensor circuit is shorted.
- The servo motor is replaced.
The operation guidelines of the EPB function are shown as below:
- Enter the EPB menu and choose relevant models according to the vehicle being tested.
- Follow the instructions displayed and press YES after completing the instructions shown.
- Enter the Enter maintenance mode menu and release the handbrake brake. And press OK after completing the instructions shown.
- Wait until the message of ‘Successful operation' pops up. And press OK to exit the menu.
- Enter the Exit maintenance mode menu and wait until the message of "Successful operation" pops up.
4.3.4 SAS (Steering Angle Sensor)
Steering Angle Sensors (SAS) System Calibration permanently stores the current steering wheel position as the straight-ahead position in the SAS EEPROM. Therefore, the front wheels and the steering wheel must be set exactly to the straight-ahead position before calibration. In addition, the VIN is also read from the instrument cluster and stored permanently in the SAS EEPROM. On successful completion of calibration, the SAS fault codes will be automatically cleared.
The operation guidelines of the SAS function are shown as below:
- Enter the SAS menu and choose relevant models according to the vehicle being tested.
- Enter the Set steering angle sensor menu and follow the instructions displayed.
- Wait until the following instruction is displayed and press Yes after completing the instructions shown.
- Follow the instructions displayed and press OK after completing the instructions shown.
- Wait until the following instruction is displayed and press OK after completing the instructions shown.
Message of ‘Function execution is completed' displayed when SAS reset function has successfully completed.
4.3.5 BMS Reset (Battery Management System)
The Battery Management System (BMS) allows the Scan Tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement and activate the rest state of the vehicle.
Battery matching must be performed in the following cases:
- The main battery is replaced. Battery matching must be performed to clear original low battery information and prevent the related control module from detecting false information.
- Battery matching is performed to re-match the control module and motoring sensor to detect battery power usage more accurately, which can avoid an error message displayed on the instrument cluster.
The operation guidelines of the BMS Reset function are shown as below:
- Enter the BMS Reset menu and choose relevant models according to the vehicle being tested.
- Turn on the ignition switch.
- Press OK to continue the BMS function.
- Enter battery capacity (within the given range) and press OK after the input.
- Enter the battery manufacturer and press OK after the input.
- Enter the 10-digit battery serial number and press OK after the input.
4.3.6 Injector Coding
This function can write the identification code of the fuel injector into the ECU so that the ECU can recognize the new injector. After the ECU or injector is replaced, the injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection.
The operation guidelines of the Injector Coding function are shown as below:
- Enter the Injector coding menu and choose relevant chassis models according to the vehicle being tested.
- Enter the Fuel injection nozzle injection volume adjustment menu.
- Read the note displayed carefully and press OK after the reading.
- Read and confirm the value stored in the cylinders.
- Enter the Change the value of cylinder menu of the replaced injector(s), enter the new 5-digit value, and then press OK.
- Wait until the message ‘Write successfully' pops up.
- Turn off the ignition switch.
- Wait until the message asks you to turn on the ignition switch.
- Re-enter the Fuel injection nozzle injection volume adjustment menu to check whether the new value(s) are shown.
4.3.7 DPF Regeneration
The Diesel Particle Filter (DPF) function manages DPF regeneration, DPF component replacement teach-in, and DPF teach-in after replacing the ECM.
DPF regeneration may be performed in the following cases:
- The exhaust back pressure sensor is replaced.
- The PM trap is removed or replaced.
- The fuel additive nozzle is removed or replaced.
- The catalytic oxidizer is removed or replaced.
- The DPF regeneration MIL is on and maintenance is performed.
- The DPF regeneration control module is replaced.
The operation guidelines of the DPF function are shown as below:
- Enter the DPF menu and choose relevant models according to the vehicle being tested.
- Enter the DPF regeneration menu.
- Read carefully and complete the requisites listed before performing the DPF regeneration function. Press OK after completing the instructions shown.
- Read the fuel tank level and make sure that it fulfills the requirement displayed.
- Read the carbon deposit load.
- Choose the “drive to warm up” option and follow the instructions listed below. Press OK after completing the instructions shown.
- Read the instructions carefully and follow the instructions shown on the screen. Press OK after completing the instructions shown.
- Follow the instructions displayed and press OK after completing the instructions shown. IMPORTANT: Please pay attention to the Note.
- Press the OK button to start the regeneration.
- Wait for the value of carbon deposit to decrease until a message of ‘Emergency regeneration has been completed' pops up, this process may take up to 40 minutes.
- Wait for 2 minutes to let the particulate filter cool down.
- Press drop out to exit the DPF function.
4.3.8 TPMS Reset
This function allows to perform the learning and matching and resetting functions of the tire pressure sensor.
TPMS Reset may be performed in the following cases:
- Tire replacement
- After troubleshooting tire pressure related problems
- Other causes of loss of signal from the tire pressure sensor
Note:
- For tire pressure sensor matching, some vehicle models may need the TPMS activation tool.
- After learning process, you may need to run the car for some while before the fault light goes off.
- Tire pressure imbalance may also cause the tire pressure light.
TPMS reset can be further divided into 4 methods, such as Automatic Relearn, Static Relearn, Copy ID and OBD Relearn, which is depending on the specific model. Also, even if the relearning methods are the same, the learning procedure may differ.
Automatic Relearn
- Install tire pressure sensor appropriately.
- Adjust all TPMS sensors to the standard value.
- Keep the vehicle at a complete standstill status for more than 20 minutes (with the engine off and power off).
- Drive at 30-100km/h for more than 15 minutes.
- The vehicle will automatically relearn the value, after that, the tire pressure warning will disappear.
- If the relearn procedure fails, please repeat steps 2-5.
Static Relearn
- Install all tire pressure sensors appropriately.
- Pull up the parking brake.
- Turn the ignition to ON/RUN with the engine off.
- Enter the tire pressure learning mode through the instrument panel on vehicle. There will be the corresponding prompt, which are differ from different car make and model, please subject to the vehicle manual or consult a professional.
- Starting from the left front wheel (some models flash the turn signal at the corresponding position), use the TPMS Activation Tool to activate the sensor, and the vehicle will sound the horn or flash the turn signal at the corresponding position after successful activation.
Note: The first sensor should be learned within 2 minutes, otherwise please repeat step 4.
OBD Relearn
- A TPMS Activation Tool is needed.
- Install tire pressure sensor appropriately.
- Adjust all TPMS sensors to the standard value.
- Activate all sensors in the order of left front, right front, right rear, left rear.
- Connect TPMS Activation Tool to the OBD port of vehicle and perform the OBD relearn function to write the sensor ID.
- Turn the ignition to ON/RUN, re-trigger all sensors in the order of left front, right front, right rear, left rear.
- Keep the vehicle powered off for more than 25 minutes.
- Drive at 30-100km/h for more than 15 minutes. If relearn successful, the tire pressure warning light will go off. Otherwise, please repeat steps 4-7.
Copy ID Relearn
Note: This learning method of the vehicle can only copy ID to the new sensor through the following three methods to replace the original sensor, if the new sensor cannot change its own ID, then the sensor can only be replaced by the OEM equipment!
Method 1:
- Use a TPMS Activation Tool to activate the original sensor, copy the sensor ID to the tire pressure activation device.
- And then program the copied ID into the new sensor through the TPMS Activation Tool (The binary of ID format should be the same as the original sensor).
- Remove the original sensor that has been just copied the ID, install the new sensor that has just been programmed, and put the tire back on.
Method 2:
- Use the TPMS Activation Tool to connect the vehicle OBD port, enter the tire pressure system, copy the ID of the sensor to be replaced.
- And then program the copied ID into the new sensor through the TPMS Activation Tool (The binary of ID format should be the same as the original sensor).
- Remove the original sensor that has been just copied the ID, install the new sensor that has just been programmed, and put the tire back on.
Method 3:
- Remove the original sensor.
- Use the TPMS Activation Tool to copy the original sensor ID into the new sensor manually (The binary of ID format should be the same as the original sensor).
- Install the new sensor to the tire correctly, set the tire pressure to the standard value, and put the tire back on the vehicle.
Note:
Tire pressure standard is usually displayed in these places:
- Vehicle owner's manual
- Label next to the driver's door (near the B-pillar)
- Drawer next to the driver's seat of the vehicle
- Fuel tank cap
This Scan Tool is not a replacement for the TPMS activation tool, and it only provides TPMS Reset/Relearn function but not activation of TPMS sensors. If you need a professional TPMS activation tool, please consult your local dealer.
4.4 J2534 Diagnostics
The VCI Box that comes with this Scan Tool can be used as a Pass-Thru device, which allows you to perform diagnostic & repairing sessions, or reprogram vehicle modules using the OEM software.
To do this, please connect the VCI to your PC via the USB-B to USB-C cable (add the USB Adapter if necessary), then connect the VCI to the OBD port of the vehicle using the Main Cable. Please refer to the picture below and check how the device is connected.

Image: Diagram illustrating the J2534 connection setup with PC, VCI Box, and vehicle.
The PC you are connecting should have the OEM software and the XTool J2534 Toolbox installed. Please visit the XTool official website, click "Support - Download Center", and find the J2534 Toolbox in the webpage.
Note: XTool does not provide any OEM diagnostic or re-flash applications; Please visit the Service Websites from the vehicle manufacturer and get the corresponding software applications.
4.5 Key Programming
The key programming software inside X100 MAX2 app can get access to the immobilizer system inside the vehicles and supports multiple functions like key programming, generate dealer key, all key lost, immobilizer reset or changing, EEPROM chip coding and much more.

Image: X100 MAX2 Professional IMMO & Key Programming features with KC501.
4.5.1 KC501 Connection
- Turn on the device.
- Power up the VCI box with vehicle connection or 12V power input. When programming keys, vehicle connection is necessary.
- Connect the device and the KC501 using the USB cable.
4.5.2 Common Immobilizer Functions
Functions include Read PIN Code/PIN Code Calculation, Check Number of Keys, Add Keys, and All Key Lost procedures. Follow the on-screen prompts for each specific function.
Note: For different models with different immobilizer modules, the key programming process will be completely different. Most of the process could be done by following the instructions on the screen. But if you are not sure how to do that, please check the tutorials. If you need to check if your car is supported, you can click the PDF icon at the top right of the model brand button.
5. Maintenance
5.1 Software Update
After activating the device, please update the software modules identified in the "Updates" screen. The device will identify all currently available software packages, and you can download them as needed. ALL software updates directly via the Internet. To access the update application, open the Diagnostic application and click Updates to enter the screen shown below:

Image: Screen showing available software updates for the X100 MAX2.
Note: After contacting your XTOOL Support to change the language configuration, you need to download all the software packages on the device again.
Cautions:
When the subscription expires, the software installed on your device itself is still available, but all updates will be invalid. If you delete specific software due to personal operation, XTOOL is not responsible for supporting the restoration of the software when the subscription expires. To renew your subscription, please contact your local dealer, or contact XTOOL technical support team directly.
5.2 Factory Reset
When you choose to restore factory settings in the Android OS system, the device will automatically erase any custom settings and data, restart and then enter the factory reset mode.
A factory reset is triggered by clicking the Settings mode from the main home page, and then clicking on “Backup & reset". Follow onscreen prompts to initiate the factory reset process.
Once the Scan Tool resets to factory default settings it will start up and then you can select the language in the following interface.
6. Troubleshooting: DTC Status Descriptions
Understanding Diagnostic Trouble Code (DTC) statuses is crucial for effective troubleshooting.
| DTC Status | Descriptions | Suggestions |
|---|---|---|
| Current/Present | Current DTC's are trouble codes that are stored in the ECU when both continuous and non-continuous (2 trip) monitors fail. Current DTC's command the MIL On the instant they are stored in the ECU. | Current DTC's can be cleared using the Clear DTC's function of the Scantool, or when the ECU monitor (2 trip monitor) has run and completed 40 consecutive trips without a fault. |
| History/Stored | History DTC's are trouble codes stored in the ECU when continuous and non-continuous monitors (2nd trip) fail. History DTC's set in conjunction with Current DTC's and are not cleared by the ECU monitor. | History DTC's set in conjunction with Current DTC's and are not cleared by the ECU monitor. History DTC's can only be cleared using the Clear DTC function of the Scantool. |
| Pending | Pending codes are codes that prep themselves when they determine a fault that engine cycle. They are basically a preliminary investigation for your engine. To simplify, a random malfunction can occur during the current drive cycle but only happen for a split second. This will cause the malfunction to throw a "pending code". | Typically pending codes are not too severe but you shouldn't ignore them either, it can be cleared using the Clear DTC's function of the Scantool. |
| Permanent | Permanent DTC's are trouble codes that are stored in the ECU when continuous and non-continuous monitors fail. Permanent DTC's are set in conjunction with Current and History DTC's. | Permanent DTC's cannot be cleared using the Clear DTC's function on the Scantool. Instead, Permanent DTC's are cleared when the ECU monitor completes and passes three consecutive trips. |
| For Volkswagen Active/static | Active/Static means that the fault is happening at the moment and can/should be taken care of. | The fault cannot be cleared directly by using the Clear DTC's function of the diagnostic tool and the internal fault of the car must be eliminated manually. |
| Passive/sporadic | It is a fault that has occurred in the past and can be cleared by Scantool, and user should to check if the DTC will appear again. | / |
7. Specifications

Image: X100 MAX2 Super Configuration highlighting key hardware specifications.
| Feature | Specification |
|---|---|
| Operating System | Android 10.0 |
| CPU | 1.5Ghz 4-Core |
| Memory | 4GB RAM + 128GB ROM |
| Display Size | 9.7 inches |
| Display Resolution | 1024*768 |
| Battery | 6400mAh 7.2V Fast Charge (46080mWh) |
| Wireless Function | Dual WIFI (2.4G/5G) |
| Communication Interface | OBD-II, Bluetooth, Wi-fi, USB |
| Software Update | 2 Years Free Update |
| External Testing Certification | CE |
| Item Weight | 8kg |
| Item Dimensions (L x W x H) | 53cm x 38inch x 17inch |
8. User Tips
- Keep Software Updated: Regularly update the device software to ensure access to the latest vehicle models, functions, and performance optimizations. This is crucial for maintaining the tool's effectiveness and compatibility.
- Language Settings: The device supports 22 languages. If you need to change the language, go to App > Setting > App version to update to the latest version, then restart the app and select your desired language.
- J2534 Programming: For J2534 ECU programming, ensure your PC has the OEM software and the XTool J2534 Toolbox installed. Visit the official XTool website for the toolbox.
9. Warranty & Support
9.1 After-Sales Services
For any technical assistance or inquiries, please contact XTOOL support:
- E-Mail: supporting@xtooltech.com
- Tel: +86 755 21670995 or +86 755 86267858 (China)
- Official Website: www.xtooltech.com
The product comes with a 2-year warranty. Even after the free update period expires, previously downloaded software can be used normally.
9.2 Remote Assistance
The device supports remote assistance via TeamViewer QuickSupport. This allows XTOOL technical support to remotely control your tablet to help with troubleshooting or specific operations.
To use remote assistance:
- Turn on the power of the tablet.
- Click Remote in the Diagnostic application. The TeamViewer screen is displayed, and the device ID will be generated.
- Provide your ID to the XTOOL technician.
- Wait for them to send a remote-control request and click Allow to accept.
9.3 Compliance Information
FCC COMPLIANCE
FCC ID: 2AW31P902
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Specific Absorption Rate (SAR) information: This device meets the government's requirements for exposure to radio waves. The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. This device was tested for typical body-worn operations with the back of the device kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation distance between the user's body and the back of the device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
ISED STATEMENT
IC: 29441-P902
PMN: Smart Diagnostic System
HVIN: P902
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Specific Absorption Rate (SAR) information: This device meets the government's requirements for exposure to radio waves. The SAR limit of Canada (ISED) is 1.6 W/kg averaged over one gram of tissue.
CE Declaration of conformity
Hereby, Shenzhen XTOOLtech Intelligent Co., Ltd declares that this Smart Diagnostic System is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
UKCA
Hereby, Shenzhen XTOOLtech Intelligent Co., Ltd declares that this Smart Diagnostic System satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.