1. Introduction
Thank you for choosing the MICTUNING Dual USB Car Charger. This product is designed to provide fast and efficient charging for your mobile devices in your vehicle. Featuring Quick Charge 3.0 technology and a dual-color LED charging reminder, it offers a convenient and safe charging solution for a wide range of USB-powered devices.
2. Package Contents
Please check the package for the following items:
- 1x MICTUNING Dual USB Car Charger
- 1x Use Manual
3. Specifications
| Feature | Detail |
|---|---|
| Power Input | DC 12V-24V |
| Maximum Output | 3.2A x 2 (Total 6.4A) |
| Charging Technology | Qualcomm Quick Charge 3.0 |
| Line Length | 1.2m (approx. 47.2 inches) |
| Charger Faceplate Size | 32mm x 22mm |
| Item Dimensions (H x W x L) | 1.3 inches x 0.9 inches x 2.2 inches |
| Item Weight | 80g |
| Special Features | Dual-color LED Charging Reminder, Reversible USB Port Design, Built-in Safety Fuse |
4. Installation
This car charger is designed to fit into a standard 32x22mm switch panel opening, commonly found in some Toyota models. Please verify the dimensions of your vehicle's available slot before installation to ensure compatibility.
- Check Compatibility: Measure the available switch panel opening in your vehicle. The charger's faceplate size is 32mm x 22mm. The overall dimensions are approximately 1.3" (Height) x 0.9" (Width) x 2.2" (Length).
- Wiring: The charger comes with a wiring harness. Typically, the red wire connects to the positive (+) power source (e.g., ACC or battery), and the black wire connects to the negative (-) ground. It is recommended to connect through a fuse for safety.
- Insert Charger: Once wiring is complete and secure, carefully insert the charger into the designated opening until it clicks into place.
- Test: Start your vehicle's engine and observe the charger's LED light. It should illuminate blue, indicating it is powered on and ready for use.
Note: If you are unsure about the wiring process, it is highly recommended to seek professional assistance to avoid damage to your vehicle or the charger.
5. Operation
The MICTUNING Dual USB Car Charger is designed for simple and intuitive operation:
- Power On: When your vehicle's engine is started, the charger's outer frame will emit a blue LED light, indicating it is powered on and ready to charge.
- Connect Device: Plug your USB charging cable into one of the two available USB ports on the charger, and connect the other end to your mobile device. The USB ports feature a convenient reversible design, allowing for easy insertion from either side.
- Charging Indicator: When charging begins, the LED light on the charger's outer frame will change from blue to red.
- Charging Complete: Once your device is fully charged, the LED light will change back to blue, reminding you that charging is complete.
6. Safety Features
Your safety and the protection of your devices are paramount. The MICTUNING car charger incorporates several safety mechanisms:
- Built-in Safety Fuse: Protects against power surges and short circuits.
- Overcharge Protection: Automatically stops charging when your device's battery is full to prevent overcharging.
- Overheat Protection: The charger will temporarily stop functioning if it detects excessive heat, resuming once it has cooled down to a safe operating temperature.
- Overcurrent Protection: Prevents damage from excessive current flow.
7. Compatibility
This charger is universally compatible with all USB port charging mobile devices, including but not limited to:
- Smartphones (e.g., iPhone, Android phones)
- Tablet PCs (e.g., iPad, Android tablets)
- iPods and other MP3 players
- Digital Cameras
- Other USB-powered electronic devices
8. User Tips
- For optimal fast charging, use high-quality USB cables that support Quick Charge 3.0.
- While the charger has dual ports, charging two devices simultaneously may slightly distribute the total available current.
- Always ensure the charger is securely installed to prevent disconnections during driving.
- The dual-color LED is a helpful visual cue; pay attention to it to know your device's charging status at a glance.
9. Troubleshooting
- Q: The charger is not powering on (no blue light).
- A: Check the wiring connections to ensure they are secure and correctly connected to the vehicle's power source. Verify that the vehicle's ignition is on if connected to an ACC power line. Check the built-in fuse for any damage.
- Q: My device is charging slowly.
- A: Ensure your device and USB cable support Quick Charge 3.0 for the fastest charging speeds. Older devices or cables may charge at standard speeds. Also, ensure only one device is connected if you suspect power distribution issues.
- Q: The LED light is not changing color.
- A: Confirm that your device is actively drawing power. If the device is already fully charged or not properly connected, the light may remain blue. If the light stays red, it indicates continuous charging, which might happen with high-capacity devices or if the device is not reaching a full charge state.
- Q: The charger gets hot during use.
- A: Some heat generation during fast charging is normal. The charger has built-in overheat protection. If it becomes excessively hot, it will temporarily stop charging to cool down. Ensure adequate ventilation around the charger.
10. Maintenance
- Keep the charger clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Avoid exposing the charger to extreme temperatures, direct sunlight for prolonged periods, or moisture.
- Do not attempt to disassemble or modify the charger, as this will void the warranty and could lead to malfunction or injury.
11. Warranty and Support
MICTUNING products are manufactured to the highest quality standards. For warranty information or technical support, please refer to the seller's policy or contact MICTUNING customer service directly. Please retain your proof of purchase for any warranty claims.