HGLRC Draknight

Contents

HGLRC Draknight 2-inch FPV Toothpick Micro Quadcopter Drone User Manual

Model: Draknight

1. Introduction

The HGLRC Draknight is a compact and agile 2-inch FPV toothpick drone, engineered for both indoor and outdoor light flying. It features a trendy design, a fully integrated All-In-One (AIO) flight controller, and a built-in receiver, offering a streamlined and high-performance flying experience.

HGLRC Draknight FPV Toothpick Micro Quadcopter Drone, front view
Figure 1: HGLRC Draknight FPV Toothpick Micro Quadcopter Drone
HGLRC Draknight product banner highlighting trendy design, integrated AIO, and built-in receiver
Figure 2: Draknight Key Features

2. Safety Information

⚠️ Warning: Not suitable for children under 36 months.

Please read and understand all safety instructions before operating the drone. Failure to follow these instructions may result in injury, damage to the drone, or property damage.

  • Always operate the drone in open areas, away from people, animals, and obstacles.
  • Do not fly near airports, restricted airspace, or sensitive areas.
  • Ensure the battery is fully charged and securely mounted before each flight.
  • Inspect the drone for any damage before and after each flight.
  • Keep fingers and loose clothing away from rotating propellers.
  • Do not operate the drone in adverse weather conditions (e.g., strong winds, rain).
  • Always maintain visual line of sight with the drone during flight.
  • Familiarize yourself with local regulations regarding drone operation.

3. Package Contents

The HGLRC Draknight package includes the following items:

  • 1x Draknight Drone
  • 2x Battery Straps
  • 1x Onboard ELRS Receiver / TBS Receiver (Optional, depending on selected variant)

4. Technical Specifications

General

PropertyValue
Product NameDraknight
Weight (excluding receiver)44.3g
MaterialPlastic
Indoor/Outdoor UseIndoor-Outdoor
Recommended Age14+ years
Is ElectricNo Battery (Drone itself does not contain a built-in battery)
Is Batteries IncludedNo
Remote ControlNo (Requires external remote controller)
Controller ModeMODE1, MODE2 (User selectable on external controller)
Control Channels2 CHANNELS
Aerial PhotographyNo (Not specifically designed for high-quality aerial photography)
Package IncludesOriginal Box
OriginMainland China

Draknight Frame

PropertyValue
Type2 inch
Wheelbase91.8mm
Maximum Supported Propeller2 inches
Size104mm x 104mm
Draknight frame diagram showing wheelbase and dimensions
Figure 3: Draknight Frame Dimensions

SPECTER12 ES2-4S AIO Flight Controller

PropertyValue
Master Control (MCU)STM32F411
Flight Control FirmwareBF HGLR-HGLRCF411SX1280_15A
Input Voltage2-4S Lipo
BEC Output5V/1.5A
Continuous ESC Current12A
Peak ESC Current15A (5s)
ESC ProtocolDshot150/300/600
ESC FirmwareZ-H-30 (Blheli_S)
Built-in ReceiverSPIExpressLRS2.4G (Optional: TBS Nano)
Built-in Image Transmission (VTX)0-25-100-400mW (Adjustable)
Specifications table for the SPECTER12 ES2-4S AIO flight controller, including MCU, IMU, OSD, BEC, and firmware details.
Figure 4: SPECTER12 ES2-4S AIO Flight Controller Specifications

Caddx Ant FPV Webcam

PropertyValue
Resolution1200TVL
Video Capture ResolutionOther (Specific resolution not detailed, typically analog FPV)
Camera Mount TypeOther (Integrated into frame)
Specifications for the Caddx Ant FPV camera, including image sensor, resolution, lens, and dimensions.
Figure 5: Caddx Ant FPV Camera Specifications

Specter 1003 Motor

PropertyValue
Motor KV10000KV (for 2S operation)
Recommended PropellerGemfan 2023 propeller
Specifications for the Specter 1003 motor, including KV, stator diameter, shaft diameter, and recommended propeller.
Figure 6: Specter 1003 Motor Specifications
  • 2S LiPo: 550mAh - 720mAh

5. Setup Guide

5.1 Initial Inspection

Before proceeding with setup, carefully inspect your Draknight drone for any visible damage during transit. Ensure all propellers are securely attached and the frame is intact.

5.2 Flight Controller (FC) and Electronic Speed Controller (ESC)

The Draknight comes with a SPECTER12 ES2-4S AIO flight controller, pre-flashed with Betaflight firmware (BF HGLR-HGLRCF411SX1280_15A) and Blheli_S ESC firmware (Z-H-30). No initial flashing is typically required, but you may update firmware via Betaflight Configurator if needed.

Detailed diagram of the Draknight drone components, including flight controller, motors, camera, and receiver, with wiring diagram and pinout for the SPECTER12 ES2-4S AIO flight controller.
Figure 7: Draknight Component Layout and Wiring Diagram
Close-up of the SPECTER12 ES2-4S AIO flight controller, highlighting connection points and features.
Figure 8: SPECTER12 ES2-4S AIO Flight Controller Pinout

5.3 Receiver Binding

The drone features a built-in SPIExpressLRS2.4G receiver. If you have the TBS Nano variant, follow the specific binding procedure for TBS Crossfire/Tracer systems.

For SPIExpressLRS 2.4G:

  1. Power on your remote controller and put it into ELRS binding mode.
  2. Connect the drone to power (e.g., a LiPo battery).
  3. The receiver on the drone should enter binding mode (indicated by a specific LED pattern, refer to ELRS documentation for details).
  4. Once bound, the receiver LED should show a solid light.
  5. Verify stick inputs in Betaflight Configurator's Receiver tab.

5.4 FPV Camera (Caddx Ant)

The Caddx Ant FPV camera is pre-installed. Ensure the lens is clean and free from obstructions. The Video Transmitter (VTX) is built into the AIO board and is adjustable from 0-25-100-400mW. You can change VTX settings via Betaflight OSD or SmartAudio/TrampHV protocols if supported by your FPV goggles/ground station.

5.5 Battery Connection

Connect a fully charged 2S LiPo battery (550mAh-720mAh recommended) to the drone's battery connector. Secure the battery using the provided battery straps.

6. Operating Instructions

6.1 Pre-Flight Check

  • Ensure propellers are free from damage and correctly oriented.
  • Check battery charge level on both drone and remote controller.
  • Confirm FPV feed is clear and free of interference.
  • Verify arming switch and flight modes are correctly set on your remote controller.

6.2 Arming and Takeoff

  1. Place the drone on a flat, level surface.
  2. Arm the drone using the designated switch on your remote controller. The motors will typically spin slowly, indicating it's armed.
  3. Slowly increase the throttle to lift off.

6.3 Flight Modes and Controller Modes

The drone supports various flight modes configured in Betaflight. Common modes include Angle (self-leveling) and Acro (manual control). Your remote controller can be set to MODE1 or MODE2, which dictates the layout of throttle, rudder, aileron, and elevator controls on the sticks. Ensure your drone's Betaflight configuration matches your controller's mode.

6.4 Landing

Reduce throttle slowly to descend. Once on the ground, disarm the drone immediately using the designated switch on your remote controller to stop the motors.

7. Maintenance

  • Propellers: Regularly check propellers for cracks, bends, or nicks. Replace damaged propellers immediately as they can cause vibrations and affect flight performance.
  • Frame: Inspect the carbon fiber frame for any signs of damage after crashes. Replace broken frame parts to maintain structural integrity.
  • Motors: Keep motors clean from dirt, dust, and debris. Ensure they spin freely without resistance.
  • Electronics: Avoid exposing the drone to moisture or extreme temperatures. If the drone gets wet, disconnect the battery immediately and allow it to dry completely before reconnecting power.
  • Battery: Store LiPo batteries in a safe, cool, dry place, ideally in a fire-retardant bag. Do not overcharge or over-discharge batteries.

8. Troubleshooting

ProblemPossible CauseSolution
Drone won't armThrottle too high, low battery, safety features engaged (e.g., accelerometer not calibrated), receiver not bound.Ensure throttle is at its lowest position. Charge battery. Calibrate accelerometer in Betaflight. Re-bind receiver. Check Betaflight 'Motors' tab for issues.
No FPV video feedVTX not powered, incorrect VTX channel/band, damaged camera/VTX, FPV goggles issue.Check VTX power in Betaflight OSD. Ensure FPV goggles are on the correct channel/band. Inspect camera and VTX for physical damage. Test goggles with another source.
Unstable flight/VibrationsDamaged propellers, loose motor screws, bent motor shaft, incorrect PID tuning.Replace all damaged propellers. Tighten motor screws. Check motors for bent shafts. Consider reviewing PID tuning in Betaflight.
Short flight timeDegraded battery, heavy flying style, incorrect battery size.Replace old or damaged batteries. Adjust flying style to be less aggressive. Ensure you are using recommended battery sizes (550-720mAh 2S).

9. User Tips

  • Betaflight Configuration: For optimal performance, connect your Draknight to Betaflight Configurator. Here you can fine-tune PID settings, adjust flight modes, and customize OSD elements to your preference.
  • Propeller Selection: While Gemfan 2023 propellers are recommended, experimenting with other 2-inch propellers can yield different flight characteristics (e.g., more thrust, longer flight time).
  • Battery Care: Always balance charge your LiPo batteries and avoid discharging them below 3.3V per cell to prolong their lifespan.
  • Practice in a Simulator: If you are new to FPV, consider practicing in an FPV simulator before flying your physical drone to build muscle memory and prevent crashes.

10. Warranty and Support

For warranty information, technical support, or service inquiries regarding your HGLRC Draknight drone, please contact the retailer or HGLRC directly through their official support channels. Keep your proof of purchase for any warranty claims.

Please note that damage caused by crashes, improper use, or unauthorized modifications may not be covered under warranty.

© 2024 HGLRC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.