Raise VW-RZ-08 / VW-RZ-58 Canbus Box Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation and operation of the Raise VW-RZ-08 and VW-RZ-58 Canbus Box. This device is designed to facilitate the integration of aftermarket Android car media players with various Volkswagen, Skoda, and Seat vehicle models, ensuring proper communication between the car's systems and the new head unit. Please read this manual thoroughly before installation to ensure correct setup and optimal performance.

2. Safety Information

• Always disconnect the vehicle's negative battery terminal before beginning any electrical installation to prevent short circuits and electrical hazards.
• Ensure all connections are secure and properly insulated to avoid damage to the device or vehicle's electrical system.
• If you are unsure about any part of the installation process, consult a qualified automotive technician.
• Do not use excessive force when removing or installing vehicle components to prevent damage.

3. Package Contents

Please verify that all components are present before proceeding with the installation:

• Raise VW-RZ-08 or VW-RZ-58 Canbus Box
• Power/CANBUS cable harness
• Additional wiring (e.g., RCA cables for video input)

Figure 3.1: Canbus Box and Wiring Harness (Cable Only variant shown)

Figure 3.2: VW-RZ-08 Canbus Box (front, side, and bottom views)

4. Installation Instructions

This section outlines the steps for installing the Canbus box and integrating it with your Android head unit. Refer to the images for visual guidance.

4.1. Pre-Installation Preparation

1. Gather all necessary components: Android head unit, fascia frame, power/CANBUS cable, GPS antenna, USB cable, rear camera cable (if applicable), and basic installation tools.
2. Crucially, disconnect the vehicle's negative battery terminal to prevent electrical shorts or damage during installation.

Figure 4.1: Pre-installation components and tools

4.2. Remove the Original Center Console

1. Use a plastic trim tool to carefully detach the decorative panel surrounding the center console. Work slowly to avoid damaging clips.
2. Unscrew the mounting screws securing the original unit.
3. Disconnect the factory wiring harness and antenna connector from the original unit.
4. Store all removed parts safely.

Figure 4.2: Removing the original head unit

4.3. Android Head Unit Wiring Connection & Functional Verification

Wiring Connection:

1. Connect the power harness (which includes the Canbus box) to the vehicle's original factory connector.
2. Ensure the Canbus decoder is correctly installed and configured if your vehicle has a CANBUS system.
3. Verify that the ACC (ignition) and constant power (B+) connections are secure and properly matched.

Accessory Installation:

1. Install the GPS antenna in an optimal location for signal reception.
2. Connect the USB extension cable for additional connectivity.
3. If applicable, connect the rear-view camera video input cable and reverse trigger wire according to the wiring diagram provided with your head unit.

Figure 4.3: Connecting the wiring harness to the head unit

System Testing:

1. Reconnect the vehicle's negative battery terminal and switch the ignition to ACC/ON.
2. Confirm that the head unit powers on properly.
3. Test all major functions:
   • Steering wheel control integration
   • Reverse camera display
   • Radio reception
   • Bluetooth connectivity
4. Ensure proper operation of all features for a fully functional system.

Figure 4.4: Testing the head unit functions, including reverse camera

4.4. Final Installation & Securing

1. Position the head unit into the fascia frame and secure it using the designated mounting screws. Ensure proper alignment and stability.
2. Align the retaining clips with their corresponding slots and carefully press the trim panel back into place. Ensure the panel fits flush against the dashboard.
3. Organize the wiring harness using cable ties to bundle and secure any excess cables. Route wiring neatly, away from moving parts and ventilation ducts, to prevent interference and potential noise.

Figure 4.5: Final installation of the head unit

5. Operating Instructions: CANBUS Setup Guide

After physical installation, configure the CANBUS settings within your Android head unit to ensure proper communication with your vehicle's systems.

1. Enter the Settings Menu:
   • Power on the unit and navigate to "Settings" then "Factory Settings".
   • You may be prompted for a password. Common default passwords include 8888, 1234, or 0000, depending on your device.
2. Select the Correct CANBUS Type:
   • In the "CAN Type" or "Protocol" section, choose the vehicle brand and model that precisely matches your car's protocol.
   • Important: Selecting the exact matching protocol is crucial. Choosing the wrong one may lead to issues such as non-functional steering wheel controls, no sound from parking sensors, or other system malfunctions.
3. Save and Restart:
   • Once the correct protocol is selected, save the settings.
   • Restart the head unit for the changes to take effect.
4. Function Test:

   After rebooting, verify the following features:

   • Steering wheel controls
   • Reverse camera and parking sensor sound
   • Automatic headlight reminders
   • Door status display
   • Air conditioning information display (if supported by your vehicle and head unit)

6. Troubleshooting

This section addresses common issues you might encounter during or after installation.

Common Troubleshooting Scenarios:

• No parking sensor sound:
  • Ensure the correct vehicle protocol is selected in the CANBUS settings.
  • Check if the factory amplifier option is enabled in your head unit's settings (if applicable).
• Steering wheel controls not working:
  • Double-check the CANBUS protocol selection.
  • If the exact protocol is unavailable, try selecting a similar vehicle protocol.
• Vehicle information (e.g., door status, AC info) not displayed:
  • Your specific vehicle model may not support full CAN data integration with aftermarket head units.
  • Verify the CANBUS protocol selection.

7. Specifications

8. User Tips

No specific user tips were available from reviews or Q&A for this product at this time. Always ensure a stable power connection and double-check all wiring before finalizing the installation.

9. Warranty and Support

For detailed warranty information and technical support, please refer to the official product documentation or contact the seller directly. A user manual in PDF format may be available for download. You can find additional guides and documents at the following link: User manual (PDF).