1. Introduction
The HGLRC SPECTER F722 40A 6in1 AIO Flight Controller is an advanced all-in-one solution designed for FPV drones, integrating both flight control and Electronic Speed Controller (ESC) functionalities into a compact board. This manual provides essential information for the proper setup, operation, and maintenance of your SPECTER F722 AIO.
Key Features:
- Integrated Flight Controller and 6-channel ESC for simplified wiring.
- Supports Y6, six-axis, and other mixed control types.
- Single-channel continuous current up to 40A, with 50A peak (10S).
- Direct plug interfaces for HD VTX Air Units or analog VTX terminals.
- Equipped with STM32F722 MCU and MPU6000 gyroscope.
- Built-in 16MB black box for flight data logging.
- Supports GPS functionality.
- Pre-flashed with BL firmware, upgradeable to Bluejay 96K for enhanced flight efficiency.
- Suitable for mainstream 2-4 inch ring machines and toothpick racks.
2. Package Contents
Please verify that all items listed below are included in your package:
- 1x HGLRC SPECTER F722 40A 6in1 AIO V2 Flight Controller
- 1x XT60 16AWG 100mm Power Cable
- 1x 30AWG 60mm Camera Cable (single-head SH1.0-3P / single-head SH1.25-3P)
- 1x 30AWG 70mm Receiver Cable (double-head SH1.0-4P)
- 1x 30AWG 70mm HD VTX Cable (single-head SH1.0-7P / single-head SH1.0-6P DJI)
- 1x 30AWG 70mm Analog VTX Cable (single-head GH1.25-6P / single-head SH1.0-7P)
- 1x 30AWG 140mm GPS Cable (double-head SH1.0-6P)
- 4x M2*6.6 Shock-absorbing Balls
- 4x M2*10 Black Nickel-plated Screws (cup head hexagon socket)
- 4x M2 Anti-loosening Self-locking Nuts
- 1x Type-C Male and Female Adapter Module
3. Specifications
| Parameter | Value |
|---|---|
| Model Name | HGLRC SPECTER F722 40A 6in1 AIO |
| MCU | STM32F722 |
| Gyroscope | MPU6000 |
| Barometer | DPS310 |
| Input Voltage | 2S-6S LiPo (8.4V-26V) |
| Continuous ESC Current | 40A per channel |
| Peak ESC Current | 50A (10S) |
| ESC Firmware | Bluejay 96K (F-H-40- Bluejay, 0.19, 48kHz) |
| Flight Controller Firmware | HGLRCF722AIO_X6 4.4.3 |
| Black Box | 16MB |
| UARTs | 3 |
| BEC Output | 5V/2A |
| OSD | Supported |
| LED | Supported |
| Buzzer (Bee Narrator) | Supported |
| ESC Protocol | DSHOT600, Oneshot, Multishot |
| Board Dimensions | 34mm x 48mm |
| Mounting Holes | 25.5mm x 25.5mm, M2 |
| Weight | Approx. 13.2g |
4. Setup and Installation
4.1 Mounting
- Ensure your drone frame has 25.5mm x 25.5mm mounting holes compatible with M2 screws.
- Place the four M2*6.6 shock-absorbing balls into the mounting holes of the flight controller.
- Secure the flight controller to your drone frame using the M2*10 black nickel-plated screws and M2 anti-loosening self-locking nuts. Do not overtighten.
4.2 Wiring Diagram
Refer to the detailed wiring diagram below for connecting motors, receiver, VTX, camera, GPS, and power. Ensure all connections are secure and correctly polarized to prevent damage.
4.3 Peripheral Connections
- Motors: Connect your motors to the designated pads on the ESC section of the AIO board. Ensure correct motor order and rotation direction as per your flight controller software configuration.
- Power: Connect the XT60 power cable to your LiPo battery (2S-6S). Connect the other end to the main power pads on the AIO board.
- Receiver: Use the provided 30AWG 70mm double-head SH1.0-4P receiver cable to connect your receiver to the appropriate UART port.
- VTX (Video Transmitter):
- For HD VTX Air Units (e.g., DJI): Use the 30AWG 70mm single-head SH1.0-7P/SH1.0-6P DJI cable for direct plug connection.
- For Analog VTX: Use the 30AWG 70mm single-head GH1.25-6P/SH1.0-7P analog image transmission cable for direct plug connection.
- Camera: Use the 30AWG 60mm single-head SH1.0-3P/SH1.25-3P camera cable to connect your FPV camera.
- GPS: Connect your GPS module using the 30AWG 140mm double-head SH1.0-6P GPS cable to the dedicated GPS UART.
- USB-C Adapter: Use the provided Type-C male and female adapter module for convenient connection to your computer for configuration.
5. Operating Instructions
5.1 Initial Configuration
- Connect the flight controller to your computer using the USB-C adapter.
- Open your preferred flight controller configurator software (e.g., Betaflight Configurator).
- Ensure the correct firmware target (HGLRCF722AIO_X6) is selected.
- Perform initial setup steps, including accelerometer calibration, port configuration for UARTs, and receiver setup.
- Configure your ESCs. The board comes with BL firmware; you may flash Bluejay 96K firmware for improved performance using a compatible ESC configurator.
- Verify motor direction and propeller orientation according to your drone's configuration.
- Perform a dry run (without propellers) to test motor response and control inputs.
5.2 Flight Modes and Tuning
Refer to your flight controller software's documentation for detailed instructions on setting up flight modes, PID tuning, and other advanced configurations. Proper tuning is crucial for stable and responsive flight.
6. Maintenance
- Regular Inspection: Periodically check all solder joints and cable connections for signs of wear, corrosion, or damage.
- Cleaning: Keep the flight controller clean from dust, dirt, and debris. Use a soft brush or compressed air. Avoid using liquids directly on the board.
- Firmware Updates: Regularly check the HGLRC website or relevant flight controller firmware repositories for updates. Keeping your firmware current can improve performance, add features, and fix bugs.
- Storage: When not in use, store the flight controller in a dry, anti-static environment.
7. Troubleshooting
Common Issues and Solutions:
- No Power to FC:
- Check battery connection and ensure it's within the 2S-6S voltage range.
- Inspect the XT60 power cable for damage or loose connections.
- Verify solder joints on the main power pads.
- Motors Not Spinning/Incorrectly:
- Ensure ESCs are calibrated correctly.
- Check motor wiring to the ESC pads for continuity and correct order.
- Verify motor direction in the flight controller software.
- Confirm that the flight controller is receiving commands from your radio receiver.
- Unstable Flight/Drifting:
- Recalibrate the accelerometer and gyroscope in the flight controller software.
- Check for balanced propellers and ensure they are securely attached.
- Review PID tuning settings; default settings may need adjustment for your specific drone.
- Inspect for any physical damage to the drone frame or components.
- No Video Feed:
- Check all connections between the camera, VTX, and flight controller.
- Ensure the VTX is receiving power and is correctly configured (channel, power level).
- Verify that the camera is functioning correctly.
- FC Not Connecting to Computer:
- Ensure the USB-C adapter is properly connected.
- Try a different USB cable or USB port on your computer.
- Install necessary USB drivers for the STM32F722 MCU.
- Restart your computer and the flight controller software.
8. User Tips
- Firmware Flashing: When updating firmware, always back up your current configuration. Use the DFU mode for flashing if you encounter issues.
- ESC Firmware: Consider flashing Bluejay 96K firmware to your ESCs for potentially smoother motor operation and improved efficiency, especially for smaller drones.
- Waterproofing: While the board is noted as 'waterproof' in some descriptions, it's generally recommended to apply conformal coating for additional protection against moisture and humidity in FPV applications.
- Cable Management: Keep all wiring neat and secure to prevent interference and accidental disconnections during flight. Use zip ties or heat shrink where appropriate.
- Testing: Always perform thorough ground testing and short hover tests in a safe environment before full flights, especially after making changes to wiring or software settings.
9. Warranty and Support
For specific warranty information, please refer to the terms and conditions provided by your retailer or contact HGLRC customer support directly. Typically, electronic components carry a limited warranty against manufacturing defects.
For technical support, firmware downloads, and additional resources, please visit the official HGLRC website or relevant community forums for FPV flight controllers.