DIVEDEER HCR-09

Contents

DIVEDEER HCR-09 Automatic Window Cleaning Robot User Manual

Thank you for purchasing this product. Please read this manual carefully before using it.

1. Important Safety Instructions and Warnings

1.1. Attention! Must Read Before Use

  • Do not allow children to operate this product. Users with physical, sensory, or psychological disorders, or those who lack knowledge of the functions and operation of this product, must be supervised by a fully competent user after being familiar with the use procedures and safety risks. Children should not use this product as a toy.
  • This product can only be used to clean framed windows and glass (not suitable for cleaning windows and glass without frames). If the window or glass frame has a damaged silicone rubber edge, please be sure to pay special attention to prevent the machine from leaking and falling off during the cleaning process. User must observe the using scenario to ensure that the product is used safely and securely.

1.2. Safety Matters

  • Always use the original adapter. Using a non-original adapter may cause product failure or damage.
  • Ensure the adapter has enough space for ventilation and heat dissipation during use. Do not wrap the power adapter with other objects.
  • Do not use the adapter in a humid environment. Do not touch the power adapter with wet hands during use.
  • Charge the window cleaner at a voltage that the power adapter can withstand.
  • Do not use a damaged power adapter, charging cable, or power plug. Before cleaning and maintaining the machine, the power plug must be unplugged. Do not disconnect power by unscrewing the extension cord to prevent electric shock.
  • Do not disassemble the power adapter. If faulty, replace the entire power adapter. For assistance, contact your local customer service or distributor.
  • The product battery, if not handled properly, poses a risk of combustion or chemical injury. Do not disassemble the battery, use in fire, or high-temperature environments above 60°C.
  • Hand over used batteries to a local professional waste battery product recycling center for recycling, complying with national laws and regulations.
  • Do not immerse this product in liquids (such as beer, water, drinks, etc.) or leave it in a humid environment for a long time.
  • Do not expose this product to sunlight and keep it away from heat sources (such as radiators, heaters, microwave ovens, gas stoves, etc.).
  • Do not place this product in a strong magnetic field.
  • Store this product out of reach of children.
  • Use this product in 0°C~40°C (32°F~104°F) ambient temperature.
  • Do not clean damaged glass and objects with uneven surfaces, as the product will not produce enough vacuum suction adsorption.
  • The built-in battery can only be replaced by the manufacturer or designated dealer/after-sales center to avoid danger.
  • Before removing or handling the battery, the power must be disconnected.
  • Operate this product in strict accordance with instructions. The manufacturer is not responsible for property damage or personal injury caused by improper use.

1.3. Risk of Electric Shock

  • Ensure the power is completely disconnected and the machine is off before cleaning or maintaining the body.
  • Do not drag the power plug through the extension cord; power off should be properly unplugged.
  • Do not continue to use the product if the machine or power supply is damaged.
  • If the machine is damaged, contact your local after-sales center or dealer for repair.
  • Do not use water to clean the machine body and power adapter.
  • Do not use this product in dangerous areas such as open fire, bathrooms with flowing water, or near swimming pools.
  • Do not damage or twist the power cord. Do not put heavy objects on the power cord or adapter.

1.4. Warnings

  • Before operation, attach the safety rope and tie it securely to a stable indoor unit.
  • Before turning on the machine, check the safety rope for damage and secure knotting.
  • When cleaning glass without a blocking table, set up a safety warning area downstairs.
  • Fully charge the built-in backup battery before use (green light on).
  • Do not use in rainy or wet weather.
  • Turn on the machine first, then place it on the window glass.
  • Ensure the machine is safely attached to the window surface before releasing your hands.
  • Before turning off the machine, hold it to avoid dropping it.
  • Do not use this product to clean frameless windows or glass.
  • Ensure the cleaning cloth is properly attached to the bottom of the machine to prevent air leakage.
  • Do not spray the machine or the bottom of the machine; spray water only on the cleaning cloth.
  • Do not allow children to use the machine.
  • Remove any items from the glass surface before use.
  • Keep hair, loose clothes, fingers, or other body parts away from the working parts of the machine.
  • Do not use the machine in areas with flammable and explosive solids or gases.

2. Product Description & Parameters

2.1. Product Description

The DIVEDEER HCR-09 Window Cleaning Robot features a vacuum motor that allows it to adhere to glass surfaces and move freely. It includes a power failure protection system with a backup battery to prevent falls during power outages. The robot has two well-designed cleaning wheels with suction cups for walking and cleaning. The microfiber cleaning cloths on the wheels are easily removable and replaceable, ensuring effective cleaning. Equipped with artificial intelligence, the robot can plan its cleaning path, detect frames, and automatically clean the entire window. A manual remote control mode provides flexible control.

2.2. Specifications

HCR-09 Specifications
AttributeValue
Model NumberHCR-09
Brand NameDIVEDEER
Input voltageAC100~240V 50Hz~60Hz
Rated power80W
Battery capacity650mAh
External dimensions295*145*100mm
Suction force2800Pa
Net weight1050g
Power failure protection time40min
Way to controlRemote control
Noise65-70dB
Border detectionAutomatic
Fall arrest controlPower failure protection (backup battery) safety rope
Cleaning modeIntelligent path planning modes
Water tank capacity30ml
Water spraying methodManual / Auto
CertificationROHS

2.3. Product Component Name

Refer to the diagram below for the main components of the HCR-09 robot:

Top view of the HCR-09 robot with numbered components
Top view of the HCR-09 robot with numbered components.
  • Orange light: charging
  • Green light: charging complete
  • Blue light: normal operation
  • Red light: machine abnormal
  • Water tank
  • One-button start
  • Power socket
  • Safety rope hanging hole
  • Water spray hole
  • Clean cloth
  • Remote control receiving window

2.4. Product Accessories

The product package includes the following items:

Product Main Body & Accessories
Overview of the HCR-09 robot and its accessories.
  • 1 x Host (Main Robot Unit)
  • 1 x Power Cord + Adapter
  • 1 x Remote Control
  • 2 pairs of Cleaning Rings
  • 1 x Add Water Bottle
  • 1 x Safety Rope
  • 1 x User Manual (PDF reference: User manual (PDF))
  • Clean Cloths (10 pieces)

3. Setup Guide

3.1. Power Connection

  1. Connect the AC power cord to the adapter.
  2. Insert the threaded connector of the adapter into the power connector of the robot fuselage and tighten it.
  3. Plug the power cord into a wall socket.

The device has a built-in battery for standby power supply in case of power failure. Ensure the battery is fully charged before use (green light is on).

  • First, turn off the power switch on the device. Connect the power cord. The orange light indicates it is charging.
  • When the green light is on, the battery is fully charged.

3.2. Install Cleaning Cloth and Ring

Ensure the cleaning cloth is placed correctly on the cleaning ring, and the cleaning ring is correctly put on the cleaning wheel to prevent air leakage.

3.3. Attach Safety Rope

  1. For glass doors and windows without a balcony, a danger warning must be placed on the ground downstairs to ensure people do not approach.
  2. Check whether the safety rope is damaged and whether the knot is loose before using.
  3. Fasten the safety rope securely before use, and tie it to a fixed object in the room to avoid danger.
Safety rope attachment diagram
Ensure the safety rope is securely attached to prevent falls.

3.4. Water Tank Filling

  1. Do not add any other cleaning agents to the water tank.
  2. Open the silicone cover and add clean, impurity-free water.
  3. Do not overfill the water tank (80% is sufficient) to maintain stable air pressure.

3.5. Attaching the Machine to Glass

  1. Press and hold the power button for 2 seconds to turn on the robot, and confirm that the fan rotates.
  2. Place the machine on the glass, keeping a certain distance from the window frame.
  3. Ensure the machine is securely attached to the glass before letting go.
Video demonstrating the HCR-09 robot cleaning a window.

4. Operating Instructions

4.1. Cleaning Function Overview

The robot is designed to clean windows efficiently with various modes and features, including ultrasonic water spray and atomization technology.

Robot spraying water with ultrasonic and atomization technology
The robot utilizes ultrasonic water spray and atomization technology for effective cleaning.

4.2. Dry Wipe

  1. For the first wipe, perform a "dry wipe" without spraying water to remove sand and loose dust from the glass surface.
  2. If water or detergent is sprayed on the cleaning cloth or glass first, it may mix with sand to form yellow mud, reducing wiping effectiveness.
  3. Dry wiping is most effective in sunny or low-humidity weather.

4.3. Wet Wipe (Automatic and Manual Spray)

The window cleaning robot features a water spray hole for wet cleaning.

Automatic Water Spray

  1. When the robot is in auto cleaning mode and moving forward, press the "AU" button on the remote control. The machine will emit two "beep...beep" sounds, indicating that automatic water spray mode is on and water will be sprayed intermittently.
  2. Press the "AU" button again on the remote control. The machine will emit a "beep" sound, indicating that the water spray mode has been turned off.

Manual Water Spray

When the robot is in auto cleaning mode and moving forward, press the water drop button on the remote control once to spray water once.

4.4. Intelligent Path Planning Modes

The robot offers several intelligent path planning modes:

  • Climb to the top and then automatic clean: The robot ascends to the top and then cleans automatically.
  • Auto clean from right to left: The robot cleans from the right side to the left side.
  • Auto clean from left to right: The robot cleans from the left side to the right side.

4.5. Remote Control Functions

The remote control allows for various operations. The front and back of the product can receive remote control signals. To replace batteries, push down the battery cover at the bottom of the back of the remote control. Align the negative pole with the spring first, press it down, and then cover the battery cover. New and old batteries or different types of batteries cannot be mixed.

Remote control diagram with button functions
Remote control layout and button functions.
  • Start/Pause: Play/Pause button.
  • Auto clean up and then down: Robot cleans from top to bottom.
  • Auto clean left and then down: Robot cleans from left to bottom.
  • Auto clean right and then down: Robot cleans from right to bottom.
  • Manually move up, down, left, right: Directional arrows for manual control.
  • AU (Automatic water spray): Toggles automatic water spray.
  • Manual water spray: Sprays water once per press.

5. Power Failure Protection

In case of power failure, the device will automatically switch to its built-in backup battery, which can provide power for up to 40 minutes when fully charged.

  • In the event of a power failure, the machine will stay in place, will not move forward, and will emit a warning sound. The red/blue lights will flash alternately. Return the machine as soon as possible to avoid it falling from the glass.
  • Use the safety rope to gently pull the device back. When pulling the safety rope, keep it as close to the glass as possible to avoid falling.

6. Troubleshooting

6.1. Machine runs slowly or fails on first use (especially on dirty outer windows):

  • When unpacking, clean and dry the supplied cleaning cloth before use.
  • Spray a little water or glass cleaner evenly on the cleaning cloth or the glass surface to be wiped.
  • After dampening and wringing out the cleaning cloth, put it into the cleaning ring for use.

6.2. Machine does not run smoothly or makes a warning sound (friction too large or too small):

  • Check if the cleaning cloth is too dirty.
  • The friction efficiency of glass stickers and fog stickers is low, making them unsuitable for use.
  • If the glass is very clean, it might be too slippery.
  • If humidity is too low (e.g., in an air-conditioned room), the glass might be too slippery after multiple wipes.

6.3. Machine cannot detect the upper edge of the window when pressing the up automatic cleaning button:

  • Press the appropriate directional key to switch to another auto clean mode.

6.4. Machine cannot wipe the upper left side of the glass:

  • Use the remote control's manual window cleaning mode to wipe the unwiped part. This can occur if the glass or cleaning cloth is slippery, or if the wiped glass width is larger.

6.5. Machine finishes cleaning prematurely:

  • Press the auto window mode button to continue the unfinished part.

6.6. Possible reasons for slipping and not climbing:

  • Friction is too small (e.g., with stickers, thermal insulation stickers, or fog stickers).
  • Cleaning cloth is too wet, or the glass is very clean and slippery.
  • Humidity is too low (air-conditioned room).
  • When starting, ensure the machine is placed at a distance from the window frame to avoid wrong judgment.

6.7. Round wheel marks remain on the glass surface after cleaning:

  • The cleaning cloth is too dirty. Replace it with a clean cloth and wipe again.

6.8. Machine doesn't run smoothly:

  • The cleaning cloth is too dirty. Replace it.
  • There are different areas on the glass surface (glass area, sticker area, thermal insulation sticker area, or fog sticker area). Use it in a single area.
  • If the screw of the cleaning wheel is loose, lock it (do not lock it too tightly, as it may affect glass glue thickness or beveled window frame performance).

6.9. Warning sound and red light flashing when machine stops due to power failure:

  • Gently pull the safety rope back to the machine, keeping it close to the glass.
  • Turn off the machine power switch.
  • Check the wire for poor contact or a broken wire.

6.10. Machine stops with red light flashing (no warning sound) due to unknown obstacles:

  • Move the machine back to a safe position via remote control, or gently pull it back with the safety rope.
  • Remove obstacles from the window.
  • Check for air leaks.

6.11. Arc marks on polished glass when light shines at night:

  • For the first time, turn off the water spraying function and use a clean cloth to remove sand.
  • For the second wipe, clean and replace the cloth, turn on water spraying, or keep the upper cleaning wheel clean and dry, and spray a little detergent or alcohol on the lower cleaning wheel (1 or 2 sprays) to eliminate arc traces. Note: All wet cleaning cloths will affect operation.

6.12. Machine cleaned all windows but didn't stop automatically:

  • Press the power button to stop the operation.

6.13. Machine will not spray water:

  • Confirm if the water spray function switch is on.
  • Clean the ultrasonic nozzle with a clean soft cloth.
  • Check if there is water in the tank and if the added cleaning solution is clean and pure.

7. Maintenance

  • **Cleaning Cloths:** Regularly clean and dry the microfiber cleaning cloths. Replace them if they become too dirty or worn to ensure optimal cleaning performance and prevent marks on the glass.
  • **Water Tank:** Ensure the water tank is filled with clean, impurity-free water. Do not use corrosive cleaning products. Clean the ultrasonic nozzle with a soft cloth if water spray issues occur.
  • **General Cleaning:** Keep the robot's body clean. Do not use water directly on the machine body or power adapter.
  • **Storage:** When not in use, untie the safety rope and store the machine and its related accessories in a dry and ventilated environment.
  • **Battery Care:** Do not disassemble the battery. If the battery needs replacement, contact authorized service personnel. Dispose of used batteries according to local regulations.

7.1. Cleaning Completed

  1. Hold the window cleaner with one hand and press the button for 2 seconds with the other hand to turn off the power.
  2. Remove the window cleaning robot from the window.
  3. Untie the safety rope and place the machine and its related accessories in a dry and ventilated environment for next use.

8. User Tips

  • **Initial Start-up:** After powering on, wait 20 seconds until the blue light stops flashing before starting work. This allows the robot to detect the glass plane.
  • **Safety First:** Always bind the safety rope when using the robot to prevent it from falling from high altitudes.
  • **Enhanced Cleaning:** For better cleaning results, spray some water on the edge of the mop pads before operation.
  • **Double Glazing:** This robot is suitable for use on double-glazed windows.
  • **Customer Support:** If you encounter any issues or have questions, especially regarding product damage or inability to use the product, contact customer service. Provide a complete unboxing video and a video demonstrating the issue after following instructions for prompt assistance.

9. Support & Further Information

For any issues not covered in this manual, or for service and repair, please contact your local customer service or distributor. The full user manual is available in PDF format for detailed instructions.

PDF Manual Reference: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.