FGHGF ATU-10-0A

Contents

ATU-10-0A Shortwave Automatic Antenna Tuner User Manual

Model: ATU-10-0A | Brand: FGHGF

1. Product Overview

The ATU-10-0A is a shortwave automatic antenna tuner designed for efficient antenna matching. Its robust housing is constructed from fine quality aluminum alloy, ensuring resistance to wear and providing stable, reliable performance. This device functions both as an automatic antenna tuner and a standing wave meter.

It is suitable for use with 20W SSB single shortwave devices and operates effectively across a wide frequency range of 1.8 to 30MHz. The tuner has a minimum starting tuning power of 0.2W and can handle a maximum measurable power of 20W.

Front panel of the ATU-10-0A tuner
Front panel of the ATU-10-0A tuner, showing the OLED display, power switch, tune button, and Type-C charging port.

2. Safety & Warnings

Warning!

  • This product is only for adult use.
  • Please keep out of reach of children and pets to avoid accidental injury or ingestion.
  • Always check if the installation is correct before operation.
  • If there is abnormal noise or equipment error after installation, please stop the device immediately.
  • Follow all instructions for proper use; Misuse may cause harm.
  • Please store the device in a dry and shady place, away from high temperatures, humidity, and direct sunlight.

3. Package Contents

Please verify that all items are present in your package:

  • 1 × ATU-10-0A Shortwave Automatic Antenna Tuner
  • 1 × Type-C Cable

Note: Only the listed package content is included. Other products shown in promotional images are not part of this package.

4. Setup and Installation

  1. Unpacking: Carefully remove the ATU-10-0A tuner and Type-C cable from the packaging.
  2. Initial Inspection: Before first use, ensure the product is free from any visible damage.
  3. Connecting to Transceiver (TRX): Connect your shortwave transceiver to the 'TRX' port on the rear of the ATU-10-0A using an appropriate coaxial cable.
  4. Connecting to Antenna (ANT): Connect your antenna to the 'ANT' port on the rear of the ATU-10-0A using an appropriate coaxial cable.
  5. Charging: If the battery is low, connect the provided Type-C cable to the 'Charge' port on the front panel and to a 5V@1A power source. The device includes a 3.7V, 1200mAh lithium battery.
Top-down view of the ATU-10-0A tuner with ANT and TRX ports highlighted
Top-down view of the ATU-10-0A tuner, highlighting the ANT (Antenna) and TRX (Transceiver) BNC connectors on the rear panel.
ATU-10-0A tuner with Type-C charging cable
The ATU-10-0A tuner shown with its included Type-C charging cable, connected to the 'Charge' port.

5. Operating Instructions

  1. Power On: Flip the red power switch on the front panel to the 'ON' position. The OLED display will illuminate.
  2. Automatic Tuning: The tuner will automatically attempt to match the antenna impedance. The display will show parameters such as PWR (Power), L (Inductance), C (Capacitance), and SWR (Standing Wave Ratio).
  3. Manual Tuning (if applicable): While the device is primarily automatic, the blue 'TUNE' button can be used to initiate or re-initiate the tuning process.
  4. Monitoring: Observe the SWR reading on the display. A lower SWR indicates a better match between the antenna and the transceiver.
  5. Power Measurement: The device also functions as a power meter, displaying the current power output. Ensure your transceiver's output power does not exceed the tuner's maximum measurable power of 20W.
  6. Frequency Range: The tuner operates within the 1.8-30MHz frequency range.
  7. Power Off: When finished, flip the red power switch to the 'OFF' position.

Note: The wording on the product's display or labels may vary depending on the manufacturing batch, but this does not affect its functionality.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the device. Do not use liquid cleaners or solvents.
  • Storage: After use, store the product in a dry place and keep it away from children. Avoid storing in areas with high temperatures, humidity, or direct sunlight.
  • Battery Care: Recharge the internal lithium battery as needed using the provided Type-C cable. Avoid over-discharging or over-charging the battery for extended periods.
  • Inspection: Periodically inspect the device and cables for any signs of wear or damage.

7. Troubleshooting

Problem Possible Cause Solution
Device does not power on Low battery; Power switch off; Internal fault Charge the battery; Ensure power switch is ON; Contact support if problem persists.
High SWR after tuning Antenna mismatch too severe; Faulty antenna/cable; Tuner limits exceeded Check antenna/cable connections; Ensure antenna is suitable for frequency; Reduce power if exceeding 20W.
Abnormal noise or error message Equipment malfunction Immediately power off the device and contact support.

8. Specifications

Feature Specification
Product Name ATU-10-0A Shortwave Automatic Antenna Tuner
Working Frequency 1.8-30MHz
Minimum Starting Tuning Power 0.2W
Maximum Measurable Power 20W
Compatible Devices 20W SSB single shortwave devices
Dimensions (L×W×H) 167 x 90 x 38mm (6.57 x 3.54 x 1.50 inch)
Charging Port Type-C (5V@1A)
Battery 1 × Lithium battery, 3.7V, 1200mAh (included)
Material Aluminum alloy
Color As Shown

Note: Light reflection and different displays may cause the color of the item in the picture to appear slightly different from the real thing. The measurement allowed error is +/- 1-3cm.

9. User Tips

  • Ensure all coaxial cable connections are secure to prevent signal loss and high SWR readings.
  • For optimal performance, keep the tuner away from strong electromagnetic interference sources.
  • Regularly check the battery level and recharge as needed to avoid interruptions during operation.

10. Warranty & Support

For technical support or warranty inquiries, please contact the manufacturer or authorized representative:

  • Manufacturer: Taiyuan yingxinfeng technology co., ltd
    Room 1304, 13th floor, No.3 Zhichuang City, No.1 Automobile Trade Road, Xuefu Industrial Park, Shanxi Transformation Comprehensive Reform Demonstration Zone Code: 030000
  • EU Authorized Representative: Prolinx GmbH, Germany
    Duesseldorf / Brehmstr.56 / 40239
    Email: eu@eulinx.eu
    Phone: +49 21131054698

A detailed user manual in PDF format may also be available for download from the seller's product page or by contacting support. (Reference: User manual (PDF))

© 2023 FGHGF. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.