HIROYASU HW-UV938

Contents

HIROYASU HW-UV938 Walkie Talkie User Manual

Comprehensive instructions for setup, operation, and maintenance.

Product Overview

The HIROYASU HW-UV938 is a versatile HF Walkie Talkie designed for a wide range of communication needs. It features a 2.4-inch TFT color LCD, 10W output power, and supports various frequency bands including SW, MW, LW, Air Band, and FM radio. Key functionalities include cross-band repeating, scrambling, NOAA weather forecasts, DTMF, and adjustable MIC/Speaker gain.

Package Contents

Upon unboxing, please verify that all items listed below are present and in good condition:

  • 1 × HIROYASU HW-UV938 Radio Body
  • 1 × 7.4V 2400mAh Li-ion Battery Pack
  • 1 × SMA-Female FM/136-174/400-520MHz High Gain Antenna
  • 1 × Desktop Charger
  • 1 × Type-C Charging Cable
  • 1 × AC Adapter
  • 1 × Belt Clip
  • 1 × Hand Strap
  • 1 × English User Manual
  • 1 × Type-C Programming Cable (Optional)
  • 1 × Shortwave Donut Antenna (Optional)

Video: Unboxing and initial setup of the HIROYASU HW-UV938, showing included accessories and basic assembly.

Setup Guide

Component Identification

Familiarize yourself with the main components of your radio:

Diagram of HIROYASU HW-UV938 with numbered components
  1. Antenna
  2. PTT (Push-To-Talk) Button
  3. Side-key 1
  4. Side-key 2
  5. Battery
  6. SW/MW/LW FM antenna (Channel knob)
  7. ON/OFF volume
  8. Indicator Light
  9. Alarm Button
  10. Display screen
  11. Keypad
  12. MIC
  13. Speaker
  14. Ear/Mic jack
  15. Type C charging port/programmable jack
Top view of HIROYASU HW-UV938 showing antenna ports, power/volume knob, and emergency button
  1. Antenna Port 1: Used for all frequency transmission and reception except short wave/middle wave/long wave/FM radio frequencies.
  2. Antenna Port 2: Used for short wave/middle wave/long wave/FM radio frequencies.
  3. Power Button/Volume Adjustment: Used to turn the device on/off and adjust the volume.
  4. Emergency Alarm Button/Customizable Button: Can be used for emergency alarms or customized functions.
  5. LED Light:
    • Green Light: Indicates the device is receiving a signal.
    • Red Light: Indicates the device is transmitting a signal.

Battery Installation and Charging

The HW-UV938 supports three charging methods:

  1. Charging with the Radio in the Charging Dock:
    1. Insert the battery into the radio.
    2. Place the radio into the charging dock.
    3. Ensure the radio is properly seated in the charger.
  2. Charging the Battery Alone in the Charging Dock:
    1. Remove the battery from the radio.
    2. Insert the battery into the charging dock.
    3. Make sure the battery is aligned correctly.
  3. Charging via USB-C Cable:
    1. Plug a USB-C cable into the charging port on the side of the radio.
    2. Connect the other end of the cable to a power adapter, computer, or power bank.

LED Indicator Status during Charging:

  • Red Light: Charging in progress.
  • Green Light: Charging complete.

Note: Use only the recommended charger and cables. Do not charge in extreme temperatures. Fully charge the battery before first use for optimal performance. Do not use cell phone fast chargers to charge this radio.

Image showing the 2400mAh rechargeable battery pack for the HIROYASU HW-UV938

Image: The 2400mAh rechargeable battery pack and its specifications.

Image showing the Type-C charging port and programming port on the side of the walkie talkie

Image: The Type-C charging port and programming port.

Operating Instructions

Basic Operation

1.1 Setting Working Frequency

The device operates in three frequency ranges: 64-620 MHz, 18-64 MHz, and 840-1000 MHz. Transmission and reception for all three bands are handled via the left main antenna port.

  1. To change the frequency band, navigate to [Basic Settings] → [17 Work Range] in the menu. After selecting the desired frequency band and confirming, the device will restart.
  2. Important: Ensure that you replace the antenna with one that matches the selected frequency band. Using an incorrect antenna may result in damage due to frequency mismatch.
Image showing the Work Range menu on the HIROYASU HW-UV938 display

Image: The 'Work Range' menu on the display, showing options for 64-620MHz, 18-64MHz, and 840-1000MHz.

1.2 Frequency Input

  1. Switch to VFO Frequency Mode: Press the # key to enter VFO Frequency Mode.
  2. Enter the Frequency: Use the numeric keypad to input the desired frequency. The input must be either 6 digits or 8 digits, depending on the selected setting.
  3. Frequency Input Settings: Navigate to [Basic Settings] → [Frequency Input 30]. Select [6 Bits] to allow 6-digit frequency input. Select [8 Bits] to require 8-digit frequency input.

1.3 Repeater Frequency Input

Method 1: Using Offset Frequency Settings

  1. Navigate to [CH Settings] → [16 Offset Freq] and use the numeric keypad to input the offset frequency.
  2. Go to [CH Settings] → [15 Offset Direction] and select either positive or negative offset.

Method 2: Direct Transmit Frequency Input

  1. In standby mode, long press the [#V/M] key to enter the [Transmit Frequency] menu.
  2. Use the numeric keypad to enter the desired transmit frequency, then press OK to confirm. The device will return to the previous menu.
  3. Go to [CH Settings] to access the sub-audio settings menu and configure the sub-audio frequency as needed.

Transmitting and Receiving Signals

1.4 Transmitting Signals

  1. Standard Transmission: Press the PTT key to initiate a call on the current frequency. The LED indicator will turn red during transmission.
  2. Multi-PTT Mode (If enabled in [Key Definition] → [1 Multi-PTT]): When Multi-PTT Mode is active, the shortcut functions of Side Key 1 and Side Key 2 are disabled. Side Key 1 transmits on Band B. Side Key 2 transmits on Band C.

1.5 Receiving Signals

When the device receives a signal on the same frequency, the LED indicator will turn green. Audio output will be enabled if:

  1. No sub-audio (CTC/DCS) is set, or
  2. The received sub-audio matches the configured sub-audio on the device.

Advanced Features

1.6 CTC/DCS Settings

Navigate to [CH Settings] to set the sub tone CTCSS or DCS.

  • CTC/DCS (Transmit & Receive): Enables both transmit and receive CTC/DCS. The device will only communicate with signals that match the set code.
  • RX CTC/DCS (Receive Only): The device will only accept signals that match the set CTC/DCS code, but transmission remains unrestricted.
  • TX CTC/DCS (Transmit Only): The device will transmit using the set CTC/DCS code, but it will receive all incoming signals without restriction.

1.7 U/V Cross-Band Repeater

Activating Cross-Band Repeater Mode:

  1. Assign a button to [26 UV Repeater] for quick activation. Alternatively, enable it via [Basic Settings] → [28 UV Repeater].
  2. Once activated: Channel C is disabled. Only Channels A and B are used for cross-band repeating. Signals received on Channel A are retransmitted on Channel B. Signals received on Channel B are retransmitted on Channel A.

Monitoring Repeater Audio: Enable [29 Repeater Monitor] in [Basic Settings] to listen to repeater voice communications.

Diagram illustrating the cross-band repeater function (U trans U, U trans V)

Image: Illustration of the cross-band repeater function, showing how the radio can transmit between UV cross-band and UU same-frequency inter-transfer.

1.8 DTMF Function

DTMF Encoding Input & Transmission:

  1. Accessing DTMF Input Mode: In standby mode, long press the - key to enter the DTMF input interface.
  2. Entering DTMF Codes: Use the numeric keypad to input the DTMF codes. Short press Side Key 2 to delete the last entered digit.
  3. Transmitting DTMF Codes: Press the PTT key to initiate a call. The device will send the DTMF code after a preset delay.

DTMF Decoding: When the device receives a signal and DTMF decoding is enabled, the received DTMF code will be displayed on the screen.

DTMF Transmission in Analog Mode: During analog transmission, pressing a key on the keypad will send the corresponding DTMF code.

Image showing the DTMF menu on the HIROYASU HW-UV938 display

Image: The DTMF menu on the display.

1.9 Text Input Function

In the Text Input Menu:

  • # key: Switch between different input methods.
  • * key: Delete text or pinyin.

Number Input [123]: Use the numeric keypad to enter numbers.

English Input [AB] / [abc]:

  • Keys 2-9: Input corresponding letters.
  • 0 key: Inputs a space.
  • 1 key: Inputs symbols.
  • Press a key multiple times to cycle through the letters (e.g., pressing 2 will display A, B, C sequentially).

Chinese Pinyin Input [PY1] / [PY2]:

  • PY1: Common Chinese characters.
  • PY2: A more extensive character set, including rare and traditional characters.
  • Enter pinyin using the numeric keypad, use ▲ ▼ keys to select characters, and press the OK key to confirm.

2.0 FM Radio & Shortwave Receiver

Defining the FM Radio Trigger: Go to the menu, then Key Define to assign a button for the FM Radio function. Pressing the defined button will enter radio mode. Pressing the PTT key will exit radio mode.

Switching Between Radio Bands: Long press the # key to switch between radio bands:

  • USW (Ultra Short Wave): 64-108 MHz
  • SW (Short Wave): 2.0-30.0 MHz
  • MW (Medium Wave): 520-1710 KHz
  • LW (Long Wave): 153-279 KHz

Switching Demodulation Modes: Short press the # key to switch the radio's demodulation mode. The USW band is fixed to FM (Frequency Modulation), which cannot be changed.

Image showing the FM Radio menu on the HIROYASU HW-UV938 display

Image: The FM Radio menu on the display, showing frequency, step, band, gain, and BFO settings.

Image showing the SW/MW/LW/FM receiving menu on the HIROYASU HW-UV938 display

Image: Instructions on how to enter the FM Radio menu and long press "# v/m" key to select SW/MW/LW/FM receiving.

2.1 One-Key Frequency Measurement & Remote Sub-Audio CTCSS/DCS Decoding

  1. After pressing the trigger button, the device enters Frequency Measurement or Remote Sub-Audio Decoding Mode and starts scanning surrounding RF signals.
  2. Press the * key to switch between Frequency Measurement Mode and Remote Sub-Audio Decoding Mode.
  3. During frequency measurement:
    • Press the PTT key or exit key to exit.
    • Press the # key to switch the frequency band.
  4. After completing frequency measurement:
    • Press the exit key to re-measure.
    • Press the menu key to save the measurement result to the VFO channel and return to VFO standby mode.
    • Press the PTT key to transmit.

2.2 Spectrum

Spectrum Scanning Mode:

  1. Press the trigger button to enter Spectrum Scanning Mode. Press the * key to exit.
  2. Short press the * key to switch input fields. The spectrum display interface includes three input items:
    • Scan Center Frequency (top-left): Adjusting this moves the scan center point.
    • SPACE: Scan step size (frequency interval between adjacent waveforms), unit: kHz.
    • DECAY: Signal amplitude attenuation, lowering the overall spectrum height for clearer observation of the main signal and adjacent channels.
  3. Press ▲ ▼ to move the indicator cursor. The bottom display will update to show:
    • Frequency at the cursor position.
    • RSSI (Received Signal Strength Indicator).
    • NOISE (Signal noise intensity).
    • GLITCH (Spurious signal strength).
Image showing the Spectrum Analyzer display on the HIROYASU HW-UV938

Image: The Spectrum Analyzer display, showing frequency and signal strength.

Menu Navigation

The HIROYASU HW-UV938 features an intuitive menu system. Use the navigation keys to scroll through options and the OK button to confirm selections.

Image of HIROYASU HW-UV938 display showing the main menu with Basic Settings, Key Define, Analog Settings, and CH Settings options

Image: Main menu of the HIROYASU HW-UV938.

Basic Settings

NOMenuSecond MenuDescription
1Name/CallsigncustomizeSet the name or callsign of the walkie-talkie.
2Voice PromptOff/OnTurn on/off the voice prompt.
3Key BeepOff/OnTurn on/off the key beep
4Lock TimerOff/5s~600sSet the lock time (5 seconds to 600 seconds).
5Key LED TimerOff/OnTurn on/off the key LED indicator
6LCD TimerOff/5s~600sSet the timed-off time for the LCD display (5 to 600 seconds)
7Brightness0~4Adjust the brightness of the LCD display (0 to 4)
8Menu ExitOff/5s~600sSet the timed-off time for menu exit (5 to 600 seconds).
9TX PriorityEdit / BusyYou can edit the transmit priority. Busy indicates that the current transmitter is busy.
10Freq Step0.25K/1.25K~5MSet the size of the frequency step. You can choose from 0.25K, 1.25K to 5M.
11TalkaroundOff/Talk around/Invert FreqTalkaround mode allows direct communication on the same frequency without using a repeater, enhancing simplicity and reducing reliance on infrastructure for communication.
12Save ModeOff/1:1/1:2/1:3Turn off the save mode. Save the one-to-one/Two/Three mode
13Scan ModeCO/TO/SEChannel/Time/Search scan
14Scan DirectionUp/DownScan upwards/Scan downwards.
15Scan ReturnOriginal CH / Current CHReturn to the original channel or current channel.
16Alarm TypeLocal Alarm / Remote Alarm / Local+RemoteLocal alarm, Remote alarm, or both.
17Work Range64-620MHz / 18-64MHz / 840-1000MHzSet the frequency range.
18Area A ModeFreq Mode / CH Mode / Zone ModeSet the Channel mode, Frequency model or zone mode.
19Area A ShowShow CH No / Show FreqSet the display way in the selected mode
20Area A ZoneZone-001~256Set the zone numbers
21Area B ModeFreq Mode / CH Mode / Zone ModeSet the Channel mode, Frequency model or zone mode
22Area B ShowShow CH No / Show FreqSet the display way in the selected mode
23Area B ZoneZone-001~256Set the zone numbers
24Area C ModeFreq Mode / CH Mode / Zone ModeSet the Channel mode, Frequency model or zone mode
25Area C ShowShow CH No / Show FreqSet the display way in the selected mode
26Area C ZoneZone-001~256Set the zone numbers
27Multi StandbyOff/OnThe multi-standby mode allows the device to switch between multiple frequencies or signals while remaining in standby status.
28UV RepeaterOff/OnCross band repeater function.
29Repeater MonitorOff/OnMonitor the working status of the repeater in real time including signal strength, connection status, etc.
30Freq Input6 bits / 8 bitsThe device can receive and process signals of different frequencies, with the supported frequency input range being 6 or 8 digits.
32Save CHCH-0001 Y~CH-1024 NSave frequently used channels in the device for quick access.
32Delete CHCH-0001 Y~CH-1024 NDelete channels that are no longer needed from the device to keep the channel list tidy and orderly.
33VersionUV Radio V1.05 2025Show the version information
34InitializationCancel / EnsureConfirm or cancel the Initialization

Key Define

This menu allows you to customize the functions of various keys for quick access to features.

NOMenuSecond MenuDescription
1Multi PTTOff/OnSet the side key 1 and side key 2 as the PTT button; if enabled, it will disable the defined button.
2Side Key 1SNone, Monit, Power Switch, Scanning, VOX, SQ, Freq Step, Multi Standby, TX Priority, Roger Beep, FM Radio, Talkaround, Alarm, Send Single Tone, Freq Detect, CTC/DCS Scan, Spectrum, Radio Sleep, Query Status, Save CH, RX AM/FM, NOAA CH, LCD On-Off, LCD Brightness, Key LED On-Off, UV RepeaterSet the side key 1 (short press) to one of the listed functions.
3Side Key 1L(Same as above)Set the side key 1 (long press) to one of the listed functions.
4Side Key 2S(Same as above)Set the side key 2 (short press) to one of the listed functions.
5Side Key 2L(Same as above)Set the side key 2 (long press) to one of the listed functions.
6Alarm Key 2S(Same as above)Set the Alarm key (short press) to one of the listed functions.
7Alarm Key 2L(Same as above)Set the Alarm key (long press) to one of the listed functions.
80 Press Long(Same as above)Set the 0 key (long press) to one of the listed functions.
91 Press Long(Same as above)Set the 1 key (long press) to one of the listed functions.
102 Press Long(Same as above)Set the 2 key (long press) to one of the listed functions.
113 Press Long(Same as above)Set the 3 key (long press) to one of the listed functions.
124 Press Long(Same as above)Set the 4 key (long press) to one of the listed functions.
135 Press Long(Same as above)Set the 5 key (long press) to one of the listed functions.
146 Press Long(Same as above)Set the 6 key (long press) to one of the listed functions.
157 Press Long(Same as above)Set the 7 key (long press) to one of the listed functions.
168 Press Long(Same as above)Set the 8 key (long press) to one of the listed functions.
179 Press Long(Same as above)Set the 9 key (long press) to one of the listed functions.

Analog Settings

NOMenuSecond MenuDescription
1SQ Level0~100-10 adjustable sensitivity for optimizing reception in varying signal conditions.
2TX Start ToneOff/OnCustomizable audio tone when power On.
3TX End ToneOff/Roger Beep 1/Roger Beep 2/Send Radio NameCustomizable audio tone at end of transmitting.
4Single Tone1750HzWhen the radio transmits a 1750 Hz tone, it is generally recognized by the repeater, which will activate and allow the transmission to go through.
5VOX On-offOff/OnToggleable voice-controlled transmission.
6VOX TH0~254Set VOX level.
7VOX Delay0~5Delay time after voice activation.
8Detect Range18-620MHz / 840-1000MHzDetects signals within the specified frequency range.
9Repeater Delay0~2000msDelay time for use via repeater.
10MIC Gain0~31Adjusts the microphone gain.
11FM Mode SPK Gain0~63Adjusts the speaker gain in FM mode.
12FM Mode DAC Gain0~15When experiencing sound distortion, lower the volume a bit.
13AM Mode SPK Gain0~63Adjusts the speaker gain in AM mode.
14AM Mode DAC Gain0~15When experiencing sound distortion, lower the volume a bit.
15Glitch TH0~10Adjust the interference threshold.
16DTMF Delay0~2000msAdjusts the delay for DTMF signals.
17DTMF Interval30~200msSets the interval between DTMF signals.
18DTMF Duration30~200msSets the duration of DTMF signals.
19DTMF ModeOff/TX Start/TX EndControls the DTMF mode.
20DTMF SelectDTMF-01~16Selects the DTMF signal to be used.
21DTMF DisplayOff/OnEnables or disables the DTMF display.
22DTMF TX Gain0~127Adjusts the transmit gain for DTMF signals.
23DTMF RX TH0~63Sets the receive threshold for DTMF signals.
24DTMF ControlOff/OnControls the DTMF functionality.
25Time CalibrateOff/OnEnables or disables time calibration.
26TX Voice Refresh0~2000msSets the transmit voice refresh rate.
27RX RSSI Refresh0~2000msSets the receive RSSI refresh rate.
28Temporary TuningOff/OnEnables or disables temporary RX setup.
28 (cont.)Temporary Tuning0~127 (RSSI) / 0~127 (Noise) / OFF/On (Power) / 0~254 (Power Level)Indicates RSSI, noise level, enables/disables temporary power settings, sets power level.

CH Settings

NOMenuSecond MenuDescription
1CTC/DCSD023N~D754NTransmit & receive CTC/DCS.
2RX CTC/DCSD023N~D754NReceive CTC/DCS signals.
3TX CTC/DCSD023N~D754NTransmit CTC/DCS signals.
4TX Freq144.125MHzSet the transmission frequency.
5DCS EncryptStandard/Encrypt 1/Encrypt 2/Encrypt 3/Mute CodeUsed to select different DCS encryption modes.
6Mute Code00000000Used to set the mute code.
7Band WidthWide/NarrowUsed to select bandwidth (wide or narrow).
8Tail ToneOff/OnUsed to turn tail tone on or off.
9ScramblerOff/1~8Used to select different voice scrambling modes.
10Busy LockOFF/Carrier Match/CTC/DCS MatchUsed to control the lock state, turn off carrier matching and CTC/DCS matching functions.
11TX PowerLow/Medium/HighSet the transmission power, can choose low, medium, or high.
12Scan AddAdd/RemoveAdd or remove scan channels.
13TOTOff/5~600sSet the time-out (TOT), can choose to turn off or set the time to 5 to 600 seconds.
14CH AliasCustomizesCustomize channel aliases.
15Offset DirectionSet the repeater offset direction.
16Offset FreqCustomizesCustomize the offset frequency.
17AM/FM RXAM/FMChoose to receive AM or FM Modulation signals.

Zone Settings

The device can set up to 256 zones. Enter the zone settings menu to edit different zones and select channel members by using the # key to choose or cancel channels.

MenuSecond MenuDescription
Zone-001~256Edit Name / Select CHSet zone name or select channels in this zone.

FM Radio

MenuSecond MenuDescription
RX StandbyOff/OnSwitch on/off RX Standby.
CH ListCH001-Empty~CH128-Empty / Edit Name / Set As CurrentEdit Name or Set As Current.

Time Management

NOMenuSecond MenuDescription
1APOOff/OnTurns the APO (Automatic Power Off) feature on or off.
2APO TimerCustomizesSets the time interval for the APO feature to turn off the device.
3AWUOff/OnTurns the Automatic Wake-Up (AWU) feature on or off.
4AWU TimerCustomizesSets the time interval for the AWU feature to wake up the device.
5System TimeCustomizesSets the current time on the device.

User Tips

  • The radio is reported to be pleasant and sensitive, with intuitive controls.
  • For receiving AM commercial broadcast stations, ensure the radio is set to the appropriate MW/SW/LW RX mode. The specifications indicate support for MW: 520-1710KHz (RX AM) and LW: 153-279KHz (RX AM).
  • When using the USB transmission feature, the range will depend on factors such as power output, antenna type, terrain, and environmental conditions. The device has a 10W output.

Maintenance

Cleaning

  • To clean the equipment and/or the battery charger, ensure they are OFF. Use an antistatic cloth (preferably) or a humid (not wet) cloth.
  • Do not pulverize directly with any liquid or product on the transceiver, battery pack, or battery charger. Never use polish home products, detergents, alcohol, or solvent for cleaning.
  • Do not use a dry cloth for cleaning, as it could cause static shock.

General Care

  • Avoid exposing the equipment or battery charger directly to water or prolonged sunlight.
  • Do not place near heat sources (radiators, etc.), in dusty or dirty environments, or near fire or explosive conditions.
  • Do not store the transceiver inside a vehicle parked in direct sunlight.
  • Avoid humidity condensation. If condensation occurs, clean with a dry cloth and allow to dry completely before use.
  • Do not place anything on the transceiver that can spill out.

Troubleshooting Guide

ProblemPossible CauseSolution
No power onBattery is dead or not inserted properlyCheck battery charge and connection
No TransmissionPTT (Push-To-Talk) button not pressed or faultyEnsure PTT is pressed; check for damage
Poor Audio QualityWeak signal or interferenceMove to a clear area; adjust antenna
Short Battery LifeOld battery or high power usageReplace battery; use power-saving mode
Cannot Receive SignalWrong channel or squelch level setVerify channel settings; adjust squelch
Distorted SoundVolume too high or speaker cloggedLower volume; clean speaker grille
OverheatingProlonged transmission or faulty unitAllow cooldown; check ventilation
Stuck in One ChannelLock feature enabledDisable channel lock function
The radio keeps transmittingVOX may be turned on or the squelch level is too sensitiveTurn off VOX or adjust squelch level

Note: If the above solutions do not resolve your problems, or if you have other inquiries, please contact technical support.

Technical Specifications

General
Frequency RangeRadio: FM 64-108MHz, SW 2.3-30MHz, MW 520-1710KHz, LW 153-279KHz
RX: 18-620MHz, 840-1000MHz
TX: 18-32MHz, 136-174MHz, 400-520MHz
Channel Capacity1024 Channels +3*VFO Channels
Channel Spacing (W/N)Analog: 25kHz/12.5kHz, Digital: 12.5K
Voltage7.4V DC
Working ModeSame frequency simplex, different frequency simplex
AntennaRemovable Antenna
Frequency Stability±2.5ppm
Working Temperature-20°C ~ +60°C
Dimension149 * 64 * 37mm
WeightAbout 307g
Transmitting
Power≤10W
Modulation ModeF3E
Maximum Deviation (W/N)≤5KHz/≤2.5KHz
SNR (W/N)-45dB/-40dB
Tx Current≤3000mA
Receiving
Sensitivity (W/N)0.22uV/0.25uV 12dB SINAD
Inter Modulation (W/N)65dB/60dB
Audio Distortion<5%
Audio Output Power≤1W (16ohm)
RX Current≤350mA
Standby Current≤100mA

Note: The above specifications are subject to change due to technical improvement without prior notice or liability.

Safety & General Information

FCC Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Safety Information for Radios

Your wireless handheld portable transceiver contains a low power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices.

Important FCC RF Exposure Requirements:

For body-worn operation, this radio has been tested and meets the FCC RF exposure guidelines when used with accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied antenna. Unauthorized antennas, modifications or attachments could damage the transmitter and may violate FCC regulations.

Normal Position

Hold the transmitter approximately 25 mm from your face and speak in a normal voice, with the antenna pointed up and away.

Compliance with RF Exposure Standards

This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material.

Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection.

Radio License

Governments regulate radios. Most classified walkie-talkies require a local government license for operation. For detailed classification and use of your two radios, please contact the local government radio management departments.

The CE marking means: Hereby, Iradio Electronics Co.,Ltd declares that the radio equipment type is in compliance with the RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available in this manual or at the following internet address: www.qziradio.com

WARNING

  • Only use this equipment for the end that this has been manufactured. The manufacturer and the salesperson won't accept any responsibility and the guarantee will invalidity in the event of inadequate use of the transceiver.
  • This equipment doesn't have components that the user can repair. Always consult to the Authorized Technical Service for any repair.

General Safety Precautions

  • It should not put into operation the equipment neither to turn off it installing and removing the battery pack. Always use the ON/OFF control.
  • Install the battery pack and the accessories (optionals) correctly, according to the indications given in this instruction manual.
  • Never transmit with the transceiver if the antenna is damaged.
  • Don't transmit with the transceiver for extended period of time.
  • Don't touch the antenna with the hand or with any part of the body when the equipment is transmitting.
  • In the event malfunction of the transceiver or of their battery charger (scent to burnt, smoke, etc.), turn off it immediately or disconnect the battery charger of the AC wall outlet and consult to the Technical Service.
  • Don't introduce any object for the holes of the speaker or for the transceiver connectors. If it uses an external headset (optional), reduce to the possible the maximum volume level; avoid levels of very high audio.
  • Don't expose the equipment or the battery charger direct to the water, direct to the sunlight for an extended period of time, not place near a heat source (radiators, etc.) to blows, to the powder excess or dirt, to the fire, to explosive or another type of dangerous conditions. Don't stored the transceiver inside a vehicle that is parked in the sunlight.
  • Avoid the humidity condensation. The air humidity is deposited in the transceiver when place of a cold atmosphere to other warm, making that the equipment doesn't work correctly. If condensation takes place in the equipment, clean a dry cloth and wait to that dries off to light it. Don't place anything on the transceiver that can spill out on the same one.
  • If the transceiver caused interferences in the video recorder, DVD, radio and television receiver, or to any other electronic equipments, take it away from the apparatus in question.
  • Don't use this transceiver in the vicinity of other electronic equipments, especially next to medical equipments. It can cause interferences in other equipments.
  • Turn off and do not use the equipment in areas where their use is restricted or prohibited (e.g. coal gas, areas with explosion atmosphere, areas where it can interference the operation of other equipments, on board airships, airports, etc.).
  • Don't operate this transceiver while it is driving a vehicle, use hands free systems ("VOX" function) and respect the traffic police indications.
  • The use of not compatible accessories with the transceiver they could limit the operation of the transceiver, and even to damages invalidating the guarantee.
  • Explosion risk if it replaces the battery pack for an incompatible one.
Recycling symbol

All articles displaying this symbol on the body, packaging or instruction manual of same, must not be thrown away into normal disposal bins but brought to specialised waste disposal centres. Here, the various materials will be divided by characteristics and recycles, thus making an important contribution to environmental protection.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.