BRS BRS-TS20

Contents

BRS-TS20 Reactor Head Outdoor Heat Collection Pot Instruction Manual

Model: BRS-TS20 | Brand: BRS

1. Introduction

The BRS-TS20 Reactor Head is a versatile outdoor heat collection pot designed for heating, windproof cooking, and multi-purpose water boiling. It features an integrated reactor for efficient infrared combustion, making it suitable for various outdoor activities including camping, trekking, and field fishing, even at high altitudes.

BRS-TS20 Reactor Head main product image

Figure 1: BRS-TS20 Reactor Head (gas tank not included)

2. Safety Warnings

Failure to follow these safety warnings may result in serious injury or property damage.

  • This product is for outdoor use or in well-ventilated environments only. Strictly prohibit use in tents, cars, rooms, or other enclosed spaces.
  • Avoid use in direct sunlight or other high-temperature environments.
  • Stop using immediately if any gas leakage is detected.
  • The product has a precise structure; do not modify it yourself to avoid danger.
  • It is strictly prohibited to disassemble or install the gas tank when the flame is not extinguished. Also, do not disassemble or install the gas tank near an open flame.
  • Keep away from flammable and explosive materials during use.
  • When igniting, do not place your head or hands directly above the stove to prevent burns.
  • The metal parts of the furnace head become very hot during use and for up to 5 minutes after use. Do not touch them.
  • Never refill used gas tanks; this may lead to accidents.
  • Children under 12 years of age should not use this product unsupervised.

3. Product Overview and Features

The BRS-TS20 Reactor Head is engineered for optimal outdoor cooking and heating performance.

  • Integrated Reactor: Features infrared combustion for efficient heating, wind and air saving, and high thermal efficiency. Designed as a professional stove for low temperatures and high altitudes.
  • High Thermal Efficiency: Achieves up to 70% thermal efficiency. Consumes approximately 79g of gas per hour and can boil 1 liter of water in about 3 minutes. Utilizes special heating metal wool that can reach temperatures of 800°C.
  • High-Altitude Performance: Successfully tested at an altitude of 4,860 meters.
  • Multi-purpose Use: Can also function as a flameless infrared radiant heater, providing effective warmth.
  • Condenser Ring Heat Collection System: This system helps to halve fuel consumption and double heating speed by efficiently protecting against wind and trapping heat with its wraparound enclosed design.
  • Durable Construction: The pot body (if used with compatible pots) is made from hard alumina, offering wear-resistance, high-temperature resistance, corrosion-resistance, and is easy to clean. Features an anti-scalding folding handle and thickened design (2mm for pot body, 1mm for pot wall).
  • Compact and Portable: Designed for nested storage, making it easy to carry for outdoor adventures.
  • Versatile Cookware Compatibility: The stove head support is compatible with a wide range of cookware, including kettles and frying pans.
Integrated Reactor showing infrared combustion and high thermal efficiency

Figure 2: Integrated Reactor with infrared combustion for high thermal efficiency.

BRS-TS20 stove in use at 4,860 meters altitude

Figure 3: High-altitude performance demonstrated at 4,860 meters.

BRS-TS20 Reactor Head used as a heater

Figure 4: The reactor head can function as an infrared radiant heater.

4. Specifications

ParameterDetail
Model NameBRS-TS20 Integrated Reactor
Ignition MethodExternal fire source
Fuel TypeButane gas, propane gas
Combustion Power1.1 kW
Gas ConsumptionApprox. 79 g/h
Weight0.214 kg
Storage SizeΦ105 mm (diameter) * 75 mm (height)
MaterialStainless steel, aluminum alloy, copper, etc.
Thermal EfficiencyUp to 70% (CE standard not less than 50%)
Package Length14 cm
Package Width14 cm
Package Height9 cm
Package Weight0.339 kg
Product dimensions and parameter table

Figure 5: Detailed product dimensions and specifications.

5. Setup and Installation

  1. Take out valve switch: Carefully remove the valve switch from its storage position.
  2. Install the gas tank:
    • Ensure the valve is in the fully closed (clockwise) position.
    • Connect the valve body to the gas tank and tighten it securely.

    NOTICE: Before ignition, always check for gas leakage. If you detect any odor (e.g., onion-like smell), immediately stop and do not attempt to ignite.

Diagram showing valve switch removal and gas tank installation

Figure 6: Steps for valve switch removal and gas tank connection.

6. Operating Instructions

  1. Ignition:
    • Turn the valve switch counterclockwise to open the gas flow (do not open too much initially).
    • Simultaneously, use an external fire source (e.g., lighter, match) to ignite the furnace head.

    NOTICE: Do not place your head or any other body parts directly above the stove during ignition.

  2. Closing the Stove:
    • Turn the valve clockwise to fully close the gas flow and extinguish the flame.
    • Allow the stove to cool completely for at least 5 minutes before handling.
    • Once cooled, unscrew the stove head from the gas tank.

7. Maintenance and Care

  • Keep the stove dry, clean, and protected from corrosion.
  • Discoloration of the furnace surface during use is a normal phenomenon and does not indicate a defect.
  • Before each use, inspect the O-seal rubber ring located in the connection between the valve body and the gas tank to ensure it is present and in good condition.
  • Keep the connection area between the valve body and the gas tank clean to prevent blockage of the gas pathway.
  • For storage, always separate the stove from the gas tank.
  • A small amount of gas leakage may occur during the installation and disassembly of the stove and gas tank. Always perform these actions in a well-ventilated area, away from any open flames.

8. Troubleshooting

ProblemPossible CauseSolution
Flame floats above the net, metal sponge body does not burn red.Using a new gas tank or high pressure in a high-temperature environment.
  • Turn down the valve and wait 1-3 minutes for the flame to settle and burn into the net.
  • Alternatively, reduce the amount of gas flow for ignition within the net.
Gas leakage detected.Improper connection, damaged O-ring, or faulty gas tank.
  • Immediately turn off the gas supply.
  • Check the connection between the valve body and the gas tank for tightness.
  • Inspect the O-seal rubber ring for damage or displacement. Replace if necessary.
  • If leakage persists, discontinue use and contact customer support.
Stove does not ignite.No gas flow, empty gas tank, or no external ignition source.
  • Ensure the gas tank is connected correctly and has fuel.
  • Verify the valve switch is open.
  • Use a reliable external fire source.

9. User Tips

No specific user tips were available from provided reviews or Q&A. However, based on product features and general outdoor stove use, consider the following:

  • Always ensure a stable, level surface for the stove to prevent tipping.
  • In cold weather, keep your gas canister warm (e.g., in a jacket pocket) before use to improve gas pressure and performance.
  • Practice assembly and ignition at home before your trip to become familiar with the process.
  • When using as a heater, ensure adequate ventilation even if flameless, to prevent carbon monoxide buildup in enclosed spaces.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the seller's official website or contact their customer service directly. Keep your purchase receipt as proof of purchase.

11. Additional Resources

A detailed user manual in PDF format is available for download:

Download User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.