BAOFENG UV-5RH Pro GPS

Contents

Baofeng UV-5RH Pro GPS Walkie Talkie User Manual

Model: UV-5RH Pro GPS

Brand: BAOFENG

1. Introduction

Thank you for choosing the Baofeng UV-5RH Pro Multi-Band Amateur Radio. This device utilizes advanced technology to provide reliable communications in demanding environments. It features a sleek and compact design, offering emergency alarm, personnel death alarm, work alone function, GPS, APRS position reporting, analog DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode. Whether for professional use in ranching, farming, driving, hunting, forest protection, tactical training, or recreational use to stay in touch with friends and family, this product offers convenience in work, life, and leisure.

To ensure proper operation and prevent personal injury or property damage, please read this manual and the Safety Information Manual carefully before use.

2. Safety and Warnings

2.1 FCC Regulatory Conformance

This equipment complies with Part 15 of the FCC Rules, designed to provide reasonable protection against harmful interference. Operation is subject to the condition that this device does not cause harmful interference. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

2.2 RF Exposure Compliance and Control

To control exposure and ensure compliance with environmental exposure limits, adhere to the following guidelines:

  • Do not remove the RF Exposure Label.
  • User awareness instructions should accompany the device.
  • Do not use if operational requirements are not met.

Operating Instructions:

  • Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key to transmit, release to receive.
  • Keep the radio unit at least 2.5cm away from the face during transmission.
  • When worn on the body, always use an approved holder, holster, case, or body harness.
  • Use only approved antennas, batteries, and accessories.

2.3 Precautions for Portable Terminals

Operating Prohibitions:

  • Do not operate in locations with fuels, chemicals, explosive atmospheres, or other flammable materials.
  • Do not operate near or in any blasting area.
  • Do not operate near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate where wireless communication equipment is prohibited.

Important Tips:

  • Use only authorized accessories.
  • Keep the product at least 2.5 cm from your body during transmission.
  • Avoid prolonged high-volume reception.
  • Do not place the product in the air bag deployment area in vehicles.
  • Keep the product and accessories out of reach of children and pets.
  • Operate within the specified temperature range.
  • Allow for cooling after continuous transmission.
  • Handle with care; do not disassemble, modify, or repair without authorization.

2.4 Precautions for Batteries

Charging Prohibitions:

  • Do not charge or replace batteries in locations with fuels, chemicals, or explosive materials.
  • Do not charge wet batteries; dry them first.
  • Do not charge deformed, leaking, or overheated batteries.
  • Do not charge with unauthorized chargers.
  • Do not charge in locations with strong radiation.
  • Avoid overcharging.

Maintenance Instructions:

  • Clean charging connector regularly.
  • Charge between 5°C and 40°C (40°F - 105°F).
  • Turn off the radio when charging the battery pack.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of batteries in fire.
  • Do not expose to direct sunlight or heat sources.
  • Do not squeeze, penetrate, or remove battery housing.

Transportation Instructions:

  • Damaged batteries must not be transported.
  • Separate batteries from metal parts to avoid short circuits during transport.
  • The radio must be switched off and secured against accidental switch-on if the battery is attached.

3. Package Contents

The Baofeng UV-5RH Pro transceiver typically includes the following items:

  • Radio body
  • Lithium-Ion battery pack
  • Instruction Manual
  • Belt Clip
  • Antenna
  • Desk charger (with wall-wart)
  • Wrist Belt

Optional accessories may include various headset and microphone configurations, such as 2PCS-2Headset, 2PCS-2Gooseneck, 4PCS-4Mic, or 4PCS-4Headset, depending on the specific package purchased.

Baofeng UV-5RH Pro GPS Walkie Talkie and accessories
Image: Baofeng UV-5RH Pro GPS Walkie Talkie and standard accessories.

4. Radio Overview

4.1 Buttons and Controls

Diagram of Baofeng UV-5RH Pro GPS Walkie Talkie components
Image: Diagram illustrating the various buttons, controls, and ports of the Baofeng UV-5RH Pro GPS Walkie Talkie.
  1. Power/Volume knob
  2. SK1- Broadcast FM and Alarm key
  3. PTT key
  4. VFO/MR mode key
  5. Status LED
  6. SK2-Flashlight and Monitor key
  7. A / B select key
  8. Key (MENU)
  9. Numeric keypad
  10. Antenna jack
  11. LED flashlight
  12. Color LCD
  13. Accessory jack
  14. Speaker and microphone
  15. One-Touch search key
  16. Key (EXIT)
  17. Navigation keys (▲ or ▼)
  18. Type-C charging port
  19. Type-C charging indicator
  20. Battery release latch

4.2 Main Keypad Controls

  • VFO/MR: Short press to switch VFO/MR mode. Long press to switch channel display mode (Channel CH, Frequency, Name).
  • A/B: Short press to switch between A (upper) and B (lower) displays. Long press to switch Dual Watch mode (Double Wait / Signal Wait / Off).
  • Sweep: Short press to enter one key sweep.
  • MENU: Short press to return to the menu. Long press to quickly enter GPS mode.
  • LOCK: Long press to lock or unlock the keyboard.
  • #: Short press to enter DTMF dial. Long press to scan on and off.
  • 0: Long press to enter weather switch to select weather channel.

4.3 Programmed Key (SK1/SK2)

The [SK1] and [SK2] keys can be programmed with different functions:

OptionFunctionality
NoneNo function assigned.
ScanEnable or disable the Scan feature.
MonitorEnable or disable the Monitor feature.
TouchEnable or disable the Touch feature.
FM RadioEnable or disable the FM Radio feature.
SOSEnable or disable the emergency alarm feature.
GNSS systemEnable or disable the GNSS system feature.
One Touch SearchEnable or disable the One Touch Search feature.
1750HzTransmits 1750Hz Tone Burst.

4.4 Status Indications (LED)

LED IndicationWhat it Indicates
Constant GreenReceiving Signal
Constant RedTransmitting Signal
Flashes GreenMonitor mode/Scanning Receiving

4.5 LCD Icon Summary

LCD Icon Summary for Baofeng UV-5RH Pro GPS
Image: Overview of the LCD display icons, indicating various radio statuses and features like VOX, Man Down, APO, FM Radio, Battery level, Keyboard locked, Bluetooth, GPS, NOAA, Signal Wait, Volume level, Squelch level, VFO Mode, Scan On, Operating Frequency, B Band, Transmit power.

5. Installation

5.1 Installing/Removing the Antenna

  • Installing: Screw the antenna clockwise into the connector on top of the transceiver until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.

5.2 Installing the Belt Clip

  • Remove the two parallel screws above the battery on the back of the radio.
  • Thread the belt clip through the holes and screw them back into the radio body.
  • To remove, unscrew counter-clockwise.

5.3 Installing the Battery Pack

Ensure the radio is turned off before attaching or removing the battery.

  • Align the battery in parallel with the radio body, with the lower edge about 1-2cm below the radio's edge.
  • Slide the battery upward along the guide-rails until it clicks into place.
  • To remove, press the battery release above the battery pack and slide the battery downward.

5.4 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

Diagram of external speaker/microphone connection
Image: Diagram showing the 2-Pin K Type connector for external speaker and microphone accessories.

6. Battery Information

6.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory. Charge it before first use or after extended storage. For optimal performance, fully charge and discharge the battery two or three times.

Use the specified charger provided by the manufacturer. Other chargers may cause explosion or personal injury. Charge the battery when the radio indicates low battery with a voice prompt.

Type-C and Base Charging options
Image: Various charging methods for the walkie-talkie, including Type-C direct charging, base charging, power bank charging, and car charging.

6.2 How to Charge

  1. Plug the AC adaptor into an outlet, then connect the cable to the DC jack on the charger. The indicator light blinks orange.
  2. Place the battery or radio into the charger, ensuring good contact with charging terminals. The indicator turns red.
  3. Full charge takes approximately 2-5 hours. The indicator turns green when charging is complete.

Note: If the radio is powered on during charging, the indicator may not turn green to show full charge as the radio consumes energy.

6.3 Using the Type-C USB Charger

The Type-C USB port allows convenient charging:

  1. Ensure the radio is OFF.
  2. Plug the Type-C USB cable into the battery's charging port.
  3. Connect the other end to a wall power outlet or compatible USB power source.
  4. An empty battery will fully charge in about 4 hours. The LCD battery meter will indicate charging progress.

Note: It is recommended to power off the radio while charging. For optimal battery life, remove the radio from the charger within 6 hours.

6.4 LED Indicator (Charging Status)

StatusLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
TroubleRed blinks fast for a long time

Note: Trouble indicates battery too warm, battery short-circuited, or charger short-circuited.

6.5 How to Store the Battery

  • Store the battery at approximately 80% discharged.
  • Keep in a low temperature and dry environment.
  • Keep away from hot places and direct sunlight.
  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.

7. Basic Operations

7.1 Power On/Off

  • Power On: Rotate the Volume/Power knob clockwise until you hear a "click". An audible double beep and display message will confirm power-on.
  • Power Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

7.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Be careful not to turn it too far and power off the radio.

7.3 Main Band/Sub Band Switch

Press the [A/B] key to switch between the A (upper) and B (lower) displays. The highlighted band is the main band (working band), and the grayed-out band is the sub band (watch band).

7.4 VFO/Channel Switch

Pressing the [VFO/MR] key switches between Frequency (VFO) Mode and Memory (MR) mode. VFO mode is useful for experimentation, while MR mode is practical for everyday use with stored channels.

7.5 Frequency (VFO) Mode

In VFO mode, use the ▲ or ▼ keys to navigate frequencies. You can also input frequencies directly using the numeric keypad (e.g., for 436.61250 MHz, enter [4][3][6][6][1][2][5][0]).

WARNING: Transmitting on unauthorized frequencies is illegal and can result in serious penalties. Always verify your authorization before transmitting.

7.6 Channel (MR) Mode and Channel Selection

Press the [VFO/MR] key to switch to Channel mode. Select channels using the ▲ or ▼ navigation keys, or by inputting channel numbers directly via the keypad.

7.7 Select a Zone

The radio supports up to 10 zones, each with a maximum of 64 channels. To select a zone, go to Menu > Zone, use ▲ or ▼ to select, then press MENU to confirm.7.8 Making a Call

  • Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED indicates transmission.
  • Frequency Mode Call: Switch to frequency mode, input the desired frequency, then hold down the [PTT] key to transmit.
  • Receive a Call: Release the [PTT] key to answer. The green LED indicates reception.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

7.9 Emergency Alert

The Emergency Alert feature signals group members for help. Press the pre-programmed [Emergency Alarm] key to activate or exit. This feature should only be used in actual emergencies.

7.10 FM Radio (FM)

The radio includes an FM radio receiver (65-108MHz). To activate, go to Menu > Radio Settings > FM Radio On/Off. Search for stations by pressing the # key or inputting frequencies directly. Press MENU or the pre-programmed FM Radio key to exit.

7.11 Radio Interrupt

  • On: Allows receiving or transmitting on the channel while FM radio is in use.
  • Off: Prevents transmission or reception while FM radio is in use.

7.12 Monitor

In standby, press the pre-programmed [Monitor] key to enter Monitor mode. This allows listening to weak signals or matched carriers without signaling. Press again to exit.

7.13 Keypad Lock

The keypad lock disables all keys except the three side keys. To enable/disable, press and hold the LOCK key for about two seconds. Auto-lock can be enabled via the menu.

7.14 Frequency Reversal

A short press of the key enables the reverse function, swapping transmit and receive frequencies.

8. Advanced Features

8.1 Scanner

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans according to your set frequency step. In Channel (MR) mode, it scans your programmed channels.

  • To enable, press and hold the # key for about two seconds.
  • Change scanning direction with ▲ or ▼ keys.
  • Press and hold the # key again to exit scanning mode.

Scan Modes:

  • Time Operation (TO): Stops on a signal, resumes after a preset timeout.
  • Carrier Operation (CO): Stops on a signal, resumes after a preset time with no signal.
  • Search Operation (SE): Stops on a signal, requires manual resume by pressing and holding #.

8.2 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method used for automation systems and remote control, common in amateur radio repeaters. The radio fully implements DTMF, including A, B, C, and D codes. To send DTMF codes, press the corresponding key(s) while holding down the PTT key.

8.3 Dual Watch

Dual Watch allows monitoring two channels. The radio features single-receiver Dual Watch with the ability to lock the transmit frequency to one of the monitored channels.

  • To enable/disable, go to Menu > Radio Settings > Dual Watch.
  • Options include OFF, Double Wait (monitors both channels), and Signal Wait (monitors both, transmits/receives on main channel only).

8.4 Manual Programming (Channels Memory)

The radio supports 640 named memory channels, each storing receive/transmit frequencies, power, signaling info, bandwidth, and ANI/PTT-ID settings. Most settings can be programmed directly via the keypad or PC software.

8.5 Repeater Programming

To program a repeater, you need its transmit and receive frequencies. In VFO mode, enter the repeater's output (receive) frequency, set the offset frequency and direction (positive or negative), and then save. You can also set CTCSS tones.

8.6 Amateur Radio Setup

For amateur radio use, it's generally recommended to turn off features like ANI, DTMFST, PTT-ID, Squelch Tail Elimination, and Roger Beep. Set bandwidth to Wide and turn off DCS and CTCSS tones unless specifically required.

10. GPS Function

The GPS function provides location information, sharing, and requesting capabilities. It requires hardware support.

GPS and APRS functionality
Image: The walkie-talkie's GPS and APRS capabilities allow for timely location information and improved coordination efficiency.

10.1 Position On/Off

In standby mode, press MENU > GNSS > GNSS On/Off. Select Off to disable or On to activate the position system. When active, the screen displays the GPS icon.

10.2 GPS Information

  • My Position: Displays Longitude, Latitude, Speed, Altitude, number of Satellites, Date, and Time.
  • Share Position: Enables sharing your position with others.
  • Request Position: Allows requesting position information from other members.

10.3 UTC Time Zone

In standby mode, press MENU > GNSS > Time Zone to select your desired UTC time zone.

10.4 Position System Use

Before using, ensure the position system is turned on (Menu > GNSS > GPS On/Off). You can also define a side key function as "GNSS System" for quick access. Press and hold MENU to enter the GPS member list and view position information.

11. Maintenance

Regular maintenance ensures the longevity and optimal performance of your Baofeng UV-5RH Pro. Always refer to the safety guidelines when performing any maintenance.

  • Cleaning: Use a soft, dry cloth to clean the radio body and accessories. Avoid using harsh chemicals or solvents.
  • Battery Care: Follow the battery maintenance instructions in Section 2.4 to prolong battery life.
  • Storage: Store the radio in a cool, dry place away from direct sunlight and extreme temperatures. Remove the battery if storing for extended periods.
  • Inspection: Periodically check the antenna, battery contacts, and accessory jacks for any signs of damage or wear.
  • Software Updates: Keep the radio's firmware updated as recommended by the manufacturer to ensure optimal performance and access to new features.

12. Troubleshooting Guide

If you encounter issues with your radio, refer to the table below for common problems and solutions. If the problem persists, contact your dealer for technical support.

PhenomenaAnalysisSolution
Cannot turn on the radio.Battery improperly installed, battery power low, or dirty/damaged battery contacts.Reinstall battery, recharge/replace battery, clean contacts.
Weak or intermittent voice during reception.Low volume, loose antenna, or blocked speaker.Increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Inconsistent frequency/signaling type, or too far from others.Verify TX/RX frequency and signaling type, move closer.
Hear unknown voices or noise.Interference from other radios, or radio in analog mode with no signaling.Change frequency, adjust squelch level, or set signaling for current channel.
Unable to hear due to too much noise/hiss.Unfavorable position (e.g., blocked by buildings), or external electromagnetic interference.Move to an open area, restart radio, or move away from interference source.
Radio keeps transmitting.VOX turned on, or headset not installed correctly.Turn off VOX, check headset installation.

13. Technical Specifications

General
Channel Capacity640
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 15 hours @ 5 watts
Operating Temperature-10°C to 60°C
Antenna Impedance50Ω
Dimensions (not including antenna)135mm x 63mm x 39mm
Weight (with Li-ON battery)290 g
MaterialPlastic
Waterproof / Water-ResistantNo
Battery CapacityHigh Capacity
Is_DisplayYes
Maximum Range5km-10km
OriginMainland China
Transmitter
Frequency Range (TX)144-148 MHz, 420-450 MHz (America version)
144-148 MHz, 430-450 MHz (Canadian version)
144-146 MHz, 430-440 MHz (EU CE version)
RF Output Power7 Watts Max (5w-10w)
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
Receiver
Frequency Range (Scan Receiver)108-136, 136-174, 220-260, 350-390, 400-520 MHz
65-108MHz (FM), 108-136MHz (AM)
Sensitivity (12 dB SINAD)-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%

Certifications: CE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee

FCC ID: 2AJGM-5RHPRO

Note: All specifications are subject to change without prior notice or liability.

14. User Tips

  • Improved Grip: Users have noted a noticeable increase in grip compared to 5W models, enhancing handling.
  • Effective Range: In urban environments, a range of 2 km is confidently achievable.
  • GPS Coordinate Exchange: The GPS function allows for coordinate exchange via radio channel upon request, which can be useful for team coordination.
  • CTCSS and Coordinate Exchange Note: Be aware that exchanging coordinates may not be compatible with CTCSS codes. If you use CTCSS for communication, you might need a separate channel without CTCSS for coordinate exchange.
  • A/B Button Usage: Remember to utilize the A/B button for switching between main and sub bands effectively.

15. Warranty and Support

For warranty information, technical support, and service inquiries, please contact your authorized Baofeng dealer or the manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.