Introduction
Thank you for purchasing the BESTVA KINGLED KP2000 Full Spectrum LED Grow Light. This manual provides detailed instructions for the mounting, installation, and proper use of your product. Please read and understand this manual completely before using the product to ensure optimal performance and safety. Only use the product as specified herein.
We hope you have a positive experience with our product. Should you encounter any issues, please do not hesitate to contact our customer service team.
Package Contents
Please verify that all the following components are included in your package:
- LED Grow Light (KP2000 unit)
- Metal Hanger
- Adjustable Hanger Rope
- Input Power Cord (US Power Cord)
Setup and Installation
Follow these steps to properly assemble and install your grow light:
-
Step One: Attach Hangers
Unbox the metal hanger kits. Attach the four small hooks to the four holes located on the back side of the light fixture.
-
Step Two: Hang the Light
Connect the adjustable rope ratchet to the metal hanger. Hang the light above your plants at an appropriate height, referring to the 'Operating Instructions' section for recommended hanging heights.
-
Step Three: Power On
Plug the power cord into a suitable electrical socket. Turn on the desired VEG or BLOOM switch located on the light fixture.
Operating Instructions
Full Spectrum and Light Modes
The KP2000 LED Grow Light provides an optimized full spectrum with 12 band wavelengths, crucial for precise crop growth. It features dedicated VEG and BLOOM switches, allowing you to adjust lighting conditions according to your plants' specific needs at different growth stages.
- 3000K Warm White: Boosts plant flowering and yields. Simulates morning sunlight.
- 5000K Cold White: Accelerates growing speed by up to 30%. Simulates daily sunlight.
- 460nm Blue Chips: Promotes plant germination and boosts seedling growth.
- 660nm Red Chips: Promotes plant flowering and fruiting, boosting blooms.
Planting Related: Lighting Schedule and Hanging Height
The following table provides reference parameters for lighting duration and hanging height based on plant growth stage. Adjust these settings flexibly according to your specific plant needs.
| Plant Stage | Switch Choice | Lighting Time | Hanging Height |
|---|---|---|---|
| Seedling | VEG | 15-18 h/d | 24-30 Inches |
| Vegetative | VEG | 15-18 h/d | 18-24 Inches |
| Flowering | BLOOM | 12-14 h/d | 12-18 Inches |
| Fruiting | VEG & BLOOM | 12-14 h/d | 12-18 Inches |
Note: These parameters are for reference only. Adjust based on specific plant requirements.
PPFD Map
The PPFD (Photosynthetic Photon Flux Density) map illustrates the light intensity available to plants at various heights:
- PPFD at 6 inches: Up to 1900 µmol/m²/s
- PPFD at 12 inches: Up to 960 µmol/m²/s
- PPFD at 18 inches: Up to 630 µmol/m²/s
Specifications
The following table details the technical specifications of the BESTVA KINGLED KP2000 LED Grow Light:
| Feature | Specification |
|---|---|
| Model | KP2000 (DC2000 Series) |
| Actual Wattage (110V) | 100W |
| LED Chips | Samsung LED chips |
| Total LED Chip Quantity | 1176 pcs |
| Full Spectrum | 460NM, 660NM, 3000K, 5000K |
| Color Rendering Index (CRI) | >80 |
| Lumen Maintenance (lm) | 6680 LM |
| PPF (µmol/s) | 420 |
| PPE (µmol/J) | 2.1 |
| PPFD (µmol/m²/s) @ 24" | 400 |
| PPFD (µmol/m²/s) @ 18" | 630 |
| PPFD (µmol/m²/s) @ 12" | 960 |
| PPFD (µmol/m²/s) @ 6" | 1900 |
| Input Voltage | 100-240VAC |
| Frequency | 50/60 Hz |
| Input Current (120VAC) | 0.83A |
| Input Current (220VAC) | 0.45A |
| Power Factor (PF) | >0.95 |
| Cover Temperature | 55°C |
| Operating Temperature | -10°C to 45°C (14°F to 113°F) |
| Driving Power Protection | Yes |
| IP Rating | IP65 |
| Power Cord Type | US Power Cord |
| Product Dimension | 415 x 340 x 80 mm (16.3 x 13.4 x 3.1 inches) |
| Product Weight | 2.7 KG (5.95 lbs) |
| Package Size | 44 x 35 x 8.5 cm |
Maintenance
- Cleaning: Regularly check the LED light for dust or dirt buildup. Clean as necessary using a dry cloth on the outside of the fixture. Do not use liquid cleaners directly on the light.
- Storage: Store the LED fixture in a dry and clean environment. The recommended ambient temperature for storage is between -20°C to 85°C (-4°F to 185°F).
Safety Recommendations
To ensure safe operation and prevent damage, please observe the following safety guidelines:
- Inspection: Do not use the light if the LED fixture or its power cord is damaged. Ensure all fittings are securely in place and there is no visible damage to the unit before use.
- Environment: This product is designed for use in greenhouses and climate-controlled LED rooms, and can be used in damp environments. However, it is NOT intended for outdoor use and must not be exposed to water.
- Moisture: Do not use sulfur vaporizers or water misters near the light. Keep the light in as dry an environment as possible.
- Temperature: The LED fixture operates optimally when the ambient air temperature is between 20°C to 35°C (68°F to 95°F).
- Cooling Down: Always allow for a cooling down period of at least 30 minutes before touching the LED board after operation.
- Disposal: The product must not be discarded as unsorted municipal waste. It must be collected separately for proper treatment, recovery, and environmentally sound disposal.
Troubleshooting
If you experience any issues with your BESTVA KINGLED KP2000 LED Grow Light, please refer to the troubleshooting steps below. If the problem persists, contact customer support for assistance.
- Light Not Turning On: Ensure the power cord is securely plugged into both the light fixture and a working electrical outlet. Check that the VEG or BLOOM switch is in the 'ON' position. Verify that the power outlet is functional.
- Dim or Flickering Light: Check for loose connections. Ensure the light is operating within the recommended voltage range (100-240VAC). If the issue continues, contact support.
- Overheating: Ensure the cooling fans are not obstructed and that there is adequate airflow around the fixture. Operate the light within the recommended ambient temperature range.
Warranty and Support
BESTVA offers a 3-year warranty for the KINGLED KP2000 LED Grow Light from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use.
- Warranty Activation: Please contact our service team within 24 hours of purchase to activate your three-year warranty.
- Parts Replacement: We offer free shipping for replacement parts for repairs within 180 days from the date of purchase. After 180 days, the buyer is responsible for shipping costs for replacement parts.
- Warranty Exclusions: The warranty does not cover damage resulting from high moisture levels, water exposure, power surges, improper hanging/mounting, incorrect use, dust buildup, or unauthorized user modifications.
- Out-of-Warranty Repairs: If parts are damaged and not covered under warranty, please contact us. You will only be responsible for the shipping fee for replacement parts.
Our company reserves the right to interpret this warranty structure. For any questions regarding our warranty policy or for warranty assistance, please contact us.
You can also refer to the official user manual PDF for additional details: BESTVA KINGLED KP2000 User Manual (PDF)
Contact Information
For support, warranty claims, or any inquiries, please reach out to us:
- Email: support@bestvaled.com
- Website: bestvaled.com