1. Product Overview
The Beitian BN-880 is a high-performance GPS module designed for precise navigation and positioning. It integrates an HMC5883L electronic compass, providing accurate heading information. This module supports multiple global navigation satellite systems (GNSS), including GPS, GLONASS, Galileo, and BeiDou, ensuring reliable positioning in various environments. It is particularly suitable for FPV drones, robotics, and other open-source flight controller applications.

2. Safety & Warnings
WARNING: To reduce the risk of injury, fire, electric shock, or property damage, please read and follow all safety information and instructions before using this product.
- This product is intended for users aged 16 years and above.
- Not suitable for children under 3 years. Small parts may present a choking hazard.
- Keep away from fire, high temperature, water, moisture, and corrosive environments.
- Do not disassemble, modify, or repair the product without authorization.
- Use the product only for its intended purpose. Misuse may cause injury or damage.
- If the product (especially electronic parts) is damaged, overheated, emits smoke, unusual odor, or noise, stop using it immediately and contact support.
- Keep packaging materials (plastic bags, foam, etc.) away from children to avoid suffocation risk.
- For indoor use only unless otherwise specified on the product or packaging.
3. Setup & Installation
3.1. Pin Description
The BN-880 GPS module features a 6-pin connector with 1.25mm spacing between pins for power and data communication. Understanding the pinout is crucial for correct integration.

| PIN | PIN Name | I/O | Description |
|---|---|---|---|
| 1 | SDA | O | Compass SDA (Serial Data Line) |
| 2 | GND | G | Ground |
| 3 | TX | O | Serial Data Output (Transmitter) |
| 4 | RX | I | Serial Data Input (Receiver) |
| 5 | VCC | I | 3.0V ~ 5.5V supply input, Typical: 5.0V |
| 6 | SCL | I | Compass SCL (Serial Clock Line) |
The module comes with a 15cm cable for easy connection to your flight controller or microcontroller. Ensure correct pin connections to avoid damage.

3.2. Physical Dimensions
The compact size of the BN-880 module allows for flexible integration into various projects.

3.3. Antenna Placement
For optimal GPS signal reception, proper antenna orientation is critical.

4. Operation
4.1. Initial Power-Up
- Preparation: Remove all protective films or packaging materials from the module.
- Power Supply: Connect the module to a DC voltage source between 2.8V and 6.0V. A typical supply voltage is 3.3V or 5.0V. Ensure stable power delivery.
- Power On: Once connected, the module will automatically power on and begin searching for satellite signals.
4.2. Satellite Acquisition
The BN-880 supports GPS, GLONASS, Galileo, BeiDou, QZSS, and SBAS. The time to first fix (TTFF) varies:
- Cold Start: Approximately 26 seconds (avg)
- Warm Start: Approximately 25 seconds (avg)
- Hot Start: Approximately 3 seconds (avg)
For optimal performance, ensure the antenna has a clear view of the sky.
4.3. Data Output
The module outputs positioning data via its UART interface (TXDA and RXDA pins). The default baud rate is 38400bps, but it supports rates from 4800bps to 115200bps. The output frequency can be configured from 1Hz to 10Hz, with a default of 1Hz.
The integrated HMC5883L compass provides heading information, which can be accessed via the SDA and SCL pins (I2C interface).
5. Maintenance & Storage
5.1. Cleaning
- Turn off the device before cleaning.
- Use a soft, lint-free cloth.
- Do not use harsh chemicals or abrasive materials.
5.2. Storage
- Store in a dry place at room temperature (15°C - 35°C).
- Keep away from direct sunlight and moisture.
- While the universal manual mentions charging for long-term storage, this passive GPS module does not contain a battery. Simply store it in a dry, stable environment.
6. Troubleshooting
- No GPS Signal / Poor Accuracy:
- Ensure the antenna side of the module is facing the sky with an unobstructed view.
- Verify power supply (VCC) is within the 2.8V-6.0V range.
- Check for strong electromagnetic interference from other components.
- Allow sufficient time for cold start acquisition (up to 26 seconds).
- No Data Output (UART):
- Confirm correct TX/RX pin connections to your microcontroller.
- Verify the baud rate setting on your microcontroller matches the module's default (38400bps) or configured rate.
- Check for proper grounding (GND).
- Compass Malfunction:
- Ensure SDA and SCL pins are correctly connected for I2C communication.
- Calibrate the compass if necessary, following your flight controller's or software's instructions.
- Keep the module away from magnetic fields or ferrous materials that could interfere with the compass.
- Module Overheating or Unusual Behavior:
- Immediately disconnect power.
- Check for short circuits or incorrect wiring.
- Contact customer support if the issue persists.
7. Specifications
| Feature | Specification |
|---|---|
| Product Name | BN-880 GPS Module |
| Model Number | FZ2920 |
| Power Supply | DC Voltage 2.8V~6.0V (Typical: 3.3V or 5.0V) |
| Consumption | Capture 50mA@5V |
| Receiving Format | GPS, GLONASS, Galileo, BeiDou, QZSS and SBAS |
| Receiving Channel | 72 Searching Channel |
| Receiving Sensitivity | Trace -167dBm, Capture -148dBm |
| Positioning Time (Cold Start) | avg 26s |
| Positioning Time (Warm Start) | avg 25s |
| Positioning Time (Hot Start) | avg 3s |
| Level Positioning Precision | 2m At Open Wind |
| Output Frequency | 1Hz-10Hz (Default 1Hz) |
| Speed Precision | 0.1 m/s (Without Aid) |
| Acceleration Precision | 0.1 m/s² (Without Aid) |
| Max Height | 18000m |
| Max Speed | 5153m/s |
| Max Acceleration | 4G |
| UART Interface | TXDA and RXDA |
| Support Rate (Baud) | 4800bps to 115200bps (Default 38400bps) |
| Working Temperature | -40℃ to +85℃ |
| Storage Temperature | -40℃ to +85℃ |
| Size | 28mm x 28mm x 10mm |
| Weight | 10g |
| Integrated Compass IC | HMC5883L |
8. User Tips
- Flight Controller Compatibility: This module is suitable for open-source flight controllers. However, it cannot be used for flight control with Simple Microcontrollers (SCM) that lack the necessary processing power or specific drivers. Always check the compatibility requirements of your flight controller software.
- Bait Boat Motherboards: For specialized applications like 16-point bait boat motherboards, ensure the motherboard's firmware and hardware are designed to interface with a GPS module like the BN-880, particularly regarding UART communication and compass data.
- Compass Calibration: For accurate heading, perform a compass calibration as instructed by your flight controller or software. Magnetic interference from nearby electronics or metal can affect compass readings.
- Power Supply Stability: A stable power supply within the specified voltage range (2.8V-6.0V) is crucial for reliable operation. Fluctuations can lead to poor performance or module damage.
9. Warranty & Support
For any problems such as product damage, missing parts, or technical inquiries, please contact the manufacturer directly.
- Phone: +86 18929344627
- Email: sales09@diymalls.com
For a comprehensive guide and additional documentation, you may refer to the official user manual PDF: View User Manual (PDF).
Manufacturer: Shenzhen DIY Maker Co., Limited, 3rd Floor, Building B1, Hekan Industrial Zone, No. 41 Wuhe South Road, Bantian, Longgang District, Shenzhen City, Guangdong Province, 518000 China.
EU Responsible Person: Evatmaster Consulting GmbH, Bettinastr. 30, 60325 Frankfurt am Main, Germany.