JIKONG JK-BD6A20S20P

Contents

JIKONG JK-BD6A20S20P Smart BMS User Manual

Model: JK-BD6A20S20P

1. Introduction

The JIKONG JK-BD6A20S20P Smart Battery Management System (BMS) is an intelligent active balance management system designed for 8S-24S Li-ion, LiFePo4, and LTO battery packs. This BMS features active balancing technology, which efficiently transfers energy between cells to maintain voltage balance with minimal energy loss, ensuring optimal battery performance and longevity. It supports continuous operation during charging, discharging, and idle states.

The system is housed in a fully enclosed aluminum alloy shell, providing excellent dustproof, waterproof, anti-voltage, and anti-vibration properties, protecting internal electronic components from environmental damage. It integrates a high-performance MCU and offers multiple communication interfaces for comprehensive monitoring and control.

JIKONG JK-BD6A20S20P Smart BMS overview with key features
Figure 1: JIKONG JK-BD6A20S20P Smart BMS with key features

2. Package Contents

Please verify that all items are present and in good condition upon unpacking:

  • 1 x JIKONG JK-BD6A20S20P Smart BMS Unit
  • 1 x Sampling Cable
  • 1 x NTC (Negative Temperature Coefficient) Sensor
JIKONG JK-BD6A20S20P Smart BMS and included accessories
Figure 2: BMS unit and included accessories

3. Setup and Wiring

Proper installation and wiring are crucial for the safe and effective operation of your BMS. Please follow these steps carefully:

  1. Connecting all the cables: Ensure all necessary cables (sampling cables, NTC) are prepared and correctly identified.
  2. Insert the cable into the BMS: Carefully connect the sampling cable to the designated port on the BMS. Refer to the interface diagram below for port identification.
  3. Connect the B-line and the P-line to the battery: Connect the main negative (B-) and positive (P-) lines from the BMS to your battery pack. Ensure polarity is correct.

The BMS features a rich interface to meet daily needs, including RS485/CAN communication modes, Bluetooth (BT), NTC temperature sensing, soft switch, SOC indicator, key switch, and active equalizer functionality.

Rich interface diagram showing CAN/RS485, GPS, NTC, Display/Switch, Hot ports
Figure 3: BMS Interface Diagram

Wiring Diagrams:

Below are typical wiring methods for 16-string and 24-string cells. Always ensure that the B- line connects to the total negative electrode of the battery pack and the P- line connects to the total positive electrode, with the load/inverter/charger connected to the P- and P+ terminals.

Wiring diagram for 16-string cells
Figure 4: Wiring Method for 16-String Cells
Wiring diagram for 24-string cells
Figure 5: Wiring Method for 24-String Cells

4. Operating Instructions

The JIKONG Smart BMS offers intelligent interaction and easy operation through its mobile APP and PC software.

4.1 Mobile APP and PC Software

The 'JIKONG SMART BMS' mobile application (available for iOS, Android, and HarmonyOS) acts as a personal lithium battery steward, providing clear, at-a-glance information. The APP supports multiple languages that can be switched automatically with your mobile phone system.

With a single click, you can view multiple critical parameters such as voltage, current, temperature, and the number of strings. The BMS allows you to freely adjust various protection values, including overcharge, overdischarge, overcurrent, temperature, and balance settings. Before making adjustments, always refer to the internal parameters of the protection board.

Mobile APP, PC software, and JIKONG home storage display options for monitoring
Figure 6: Monitoring Options (Mobile APP, PC Software, Home Display)
Mobile app screenshot showing multi-screen display and data connection (voltage, current, temp, SOC, alarm, cycles)
Figure 7: Mobile App Multi-screen Display

4.2 Inverter Communication

The BMS supports various mainstream inverter communication protocols, which can be configured via the host computer software.

Screenshot of PC software interface for settings and logging, with a table of supported CAN protocols
Figure 8: PC Software Interface and Supported CAN Protocols

Supported CAN Protocols:

Protocol NameCompatible Inverter Brands
Low-voltage hybrid inverter CAN communication protocolJIKONG, Growatt, Voltronic, WOW
PYLON CANBUS Protocol V1.2Pylontech
Growatt xxSxxP ESS Protocol V2.01Growatt
CAB-BUS_BMS_Protocol_201707NIU
INVT BMS CAN Bus protocol V1.02INVT
GoodWe LV BMS Protocol (CAN) V1.7(For ES/EM/BP Series)Goodwe
FSS-ConnectingBat-TI-en-10 | Version 1.0China Tower
PACE BMS Modbus Protocol for RS485SMA, Srne

5. Maintenance

The JIKONG Smart BMS is designed for durability and minimal maintenance, thanks to its robust construction and intelligent features.

5.1 Physical Protection

The BMS features a fully enclosed aluminum alloy shell, providing superior protection against dust, water, voltage fluctuations, and vibrations. The internal components are filled with high-strength insulating material, absorbing external pressures and vibrations.

Dustproof and waterproof features, anti-voltage and anti-vibration design
Figure 9: Dustproof, Waterproof, Anti-voltage, and Anti-vibration Design

5.2 Heat Dissipation

The casing is made of aluminum alloy using one-piece molding technology, which offers excellent heat dissipation with a high thermal conductivity of less than 300 W/(m·K). This is significantly better than iron (<60 W/(m·K)) or plastic (>1 W/(m·K)), ensuring stable operation even under demanding conditions.

Diagram illustrating the fully aluminum alloy shell and superior heat dissipation
Figure 10: Superior Heat Dissipation with Aluminum Alloy Shell

5.3 Active Balancing

The intelligent active balancing technology (0.6A-2A adjustable current) continuously works to equalize cell voltages, extending battery lifespan and ensuring more stable and reliable performance. This non-lossy balancing method transfers energy efficiently without generating excessive heat.

Table showing 'Excellent balance effect' with voltage differences before and after balancing for 16S cells
Figure 11: Excellent Balance Effect (Example for 16S 100AH Battery)

6. Troubleshooting

If you encounter any issues with your JIKONG Smart BMS, consider the following general troubleshooting steps:

  • No Power/No Display: Check all wiring connections, especially the main B- and P- lines, and the sampling cables. Ensure they are securely connected and correctly polarized.
  • Balancing Issues: Verify that the active balancing function is enabled in the mobile APP or PC software. Check individual cell voltages to identify any significant discrepancies.
  • Communication Problems (Bluetooth/RS485/CAN): Ensure the mobile APP is updated to the latest version. For PC communication, confirm that the correct drivers are installed and the communication protocol is properly configured for your inverter or display.
  • Over-protection Triggered: If the BMS triggers an overcharge, overdischarge, or overcurrent protection, check the battery pack's voltage, current draw, and temperature. Adjust protection parameters in the APP/software if necessary, but always within safe limits for your battery chemistry.
  • Temperature Alarms: Ensure the NTC sensor is correctly installed and making good contact with the battery cells. Check for any abnormal heat generation from the battery or BMS.

For complex issues or persistent problems, please contact JIKONG customer support for assistance.

7. Specifications

FeatureSpecification
Model NumberJK-BD6A20S20P
Accessory TypeBattery Accessories
OriginMainland China
CertificationCE
Battery IncludedNo
Charger IncludedNo
High-concerned chemicalNone
Number of Battery Strings (Li-ion/LiFePo4)8S-20S
Number of Battery Strings (LTO)12S-25S
Balance MethodActive Balance (Full State On)
Balance Current0.6A
Conductive Resistance in Main Circuit1mΩ
Continuous Discharge Current200A
Continuous Charge Current200A
Maximum Discharge Current (MAX 30s)200A
Over Charge Protection Current (A)10-100A
Other Interfaces (Default)RS485
Other Interfaces (Customized)CANBUS, HEAT
Dimensions (L x W x H)162mm x 102mm x 16.6mm (Note: Data tolerance range is ±2mm)
Wiring OutputCommon Port
Single Cell Voltage Range1-5V
Voltage Detection Accuracy±5mV
Over Charge Protection Voltage1.2-4.35V Adjustable
Over Charge Release Voltage1.2-4.35V Adjustable
Over Current Detect Delay2-120S Adjustable
Over Discharge Protection Voltage1.2-4.35V Adjustable
Over Discharge Release Voltage1.2-4.35V Adjustable
Quantity of Temperature Detection3Pcs
Temp ProtectionYes
Short Circuit ProtectionYes
Coulomb CounterYes
Bluetooth FunctionSupport for Android/iOS phone
JIKONG Product Specifications table with detailed technical parameters
Figure 12: Detailed Product Specifications
Product specification diagram with dimensions (162mm L, 102mm W, 16.6mm H)
Figure 13: Product Dimensions

8. User Tips

  • Regular Monitoring: Utilize the mobile APP or PC software to regularly monitor your battery's health, including individual cell voltages, overall pack voltage, current, and temperature. This helps in early detection of potential issues.
  • Correct Wiring: Always double-check all wiring connections, especially the balance leads and main power cables, before powering on the system. Incorrect wiring can lead to damage to the BMS or battery.
  • Optimize Balancing: Take advantage of the active balancing feature to prolong the life and improve the performance of your battery pack. Ensure the balancing current and settings are appropriate for your battery type and capacity.
  • Environmental Protection: While the BMS is robust, avoid exposing it to extreme temperatures or harsh environments beyond its specified operating conditions to ensure long-term reliability.
  • Firmware Updates: Check the manufacturer's website or app for any available firmware updates, which may offer improved performance, new features, or bug fixes.

9. Warranty and Support

For any technical support, warranty claims, or inquiries regarding your JIKONG JK-BD6A20S20P Smart BMS, please contact the manufacturer, Chengdu Jikong Technology Co., Ltd., or your authorized reseller. Ensure you have your product model number and purchase details ready when seeking support.

Chengdu Jikong Technology Co., Ltd. is a high-tech enterprise specializing in active balance power battery management systems, committed to product quality and environmental protection. They have a strong R&D team and are ISO9001 certified.

© 2024 JIKONG. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.