1. Introduction
The HGLRC Zeus VTX PRO 1.6W is a high-power video transmission module designed for RC FPV racing drones, offering long-range capabilities. It features a built-in microphone, a robust CNC heat sink shell, and an MMCX antenna interface. This manual provides detailed instructions for its installation, operation, and maintenance.
2. Specifications
| Feature | Description |
|---|---|
| Model | Zeus VTX PRO 1.6W |
| Built-in Microphone | Yes |
| Input Voltage | DC 7-36V |
| Output Voltage | 5V/500mA |
| Output Power (selectable) | PIT / 25mW / 400mW / 800mW / 1.6W |
| Antenna Interface | MMCX |
| Channels | Standard 40 channels (A/B/E/F/R frequency group) |
| Mounting Hole | 20x20mm, M2 |
| Dimensions | 25mm x 37mm x 6.5mm |
| Weight | 13g |
| Material | Metal (CNC Heat Sink Shell) |
| Recommended Age | 14+ years |
| Certification | CE |
3. Package Contents
Verify that all items are present in your package:
- 1 x HGLRC Zeus VTX PRO 1.6W Video Transmission Module
- 1 x 80mm 5.8G MMCX Linear Brass Antenna
- 1 x MMCX to SMA 100mm Adapter Cable
- 1 x GH1.25 6Pin 100mm Cable
4. Safety Information
- Always ensure correct polarity when connecting power to avoid damage.
- Operate the VTX within the specified input voltage range (DC 7-36V).
- Do not power on the VTX without an antenna connected, as this can permanently damage the module.
- High-power VTX modules can generate significant heat. Ensure adequate airflow for cooling, especially during high-power operation.
- Adhere to local regulations regarding FPV transmission frequencies and power levels.
5. Setup and Installation
5.1. Physical Installation
The Zeus VTX PRO 1.6W features 20x20mm M2 mounting holes, allowing for easy integration into most FPV drone frames. Secure the module using appropriate screws and standoffs, ensuring it is isolated from conductive surfaces.
5.2. Wiring Diagram
Connect the VTX to your flight controller and power source according to the following diagrams. Pay close attention to the pin assignments for VID (Video), GND (Ground), 5V OUT, RX (Receiver for SmartAudio/TrampHV), and DC IN (Power Input).

Figure 1: VTX Pinout and Indicator Lights. This diagram illustrates the connection points on the VTX module (VID, GND, 5V OUT, RX, GND, DC IN) and the location of the Power (red), Channel (blue), and FR (green) indicator lights, along with the channel and FR/power buttons.

Figure 2: VTX to Flight Controller Wiring. This diagram shows how to connect the VTX to a typical flight controller. Connect the VTX's VID to the FC's VIO, VTX's 5V OUT to FC's 5V, VTX's RX to FC's TX4 (or other available UART TX), and VTX's DC IN to a suitable power source (7-36V) on the FC, ensuring all GNDs are connected.
5.3. Antenna Connection
Connect the provided MMCX antenna or a compatible 5.8Ghz MMCX antenna to the VTX module. Ensure the connection is secure to prevent signal loss and VTX damage.
6. Operating Instructions
6.1. Power On/Off
The VTX powers on automatically when DC 7-36V is supplied to the DC IN pins. To power off, disconnect the power source.
6.2. Channel, Band, and Power Adjustment
The VTX features two buttons: 'channel' and 'FR/power'.
- Channel Button: Short press to cycle through channels (CH1-CH8) within the current band.
- FR/Power Button:
- Short Press: Cycles through frequency bands (A, B, E, F, R).
- Long Press (approx. 3 seconds): Cycles through power levels (PIT, 25mW, 400mW, 800mW, 1.6W).
Note: Always verify your selected channel, band, and power level using the indicator lights or OSD (if SmartAudio/TrampHV is configured) to avoid interference with other pilots.
6.3. Indicator Lights
The VTX has three indicator lights:
- Power Indicator (Red): Illuminates when the VTX is powered on.
- Channel Indicator (Blue): Indicates the currently selected channel. The number of flashes corresponds to the channel number (e.g., 1 flash for CH1, 2 flashes for CH2, etc.).
- FR Indicator (Green): Indicates the currently selected frequency band. The number of flashes corresponds to the band (e.g., 1 flash for Band A, 2 flashes for Band B, etc.).
6.4. SmartAudio/TrampHV (RX Pin)
The RX pin allows for VTX control via your flight controller's OSD (On-Screen Display) using protocols like SmartAudio or TrampHV. Refer to your flight controller's manual and Betaflight/ArduPilot documentation for configuration details. This enables changing channels, bands, and power levels directly from your FPV goggles or transmitter.
7. Maintenance
- Keep the VTX clean and free from dust and debris.
- Regularly check all wiring connections for looseness or damage.
- Ensure the CNC heat sink is not obstructed to allow for proper heat dissipation.
- Avoid exposing the VTX to excessive moisture or extreme temperatures.
8. Troubleshooting
- No Video Signal:
- Check power connections and ensure the VTX is receiving power (red indicator light).
- Verify antenna is securely connected.
- Ensure your FPV goggles/receiver are on the correct frequency/channel/band.
- Check video signal wire (VID) connection.
- Poor Video Quality/Short Range:
- Ensure the antenna is not damaged and is correctly oriented.
- Check for obstructions between the drone and receiver.
- Increase VTX power output (if legally permitted and within thermal limits).
- Check for local interference sources.
- VTX Overheating:
- Ensure adequate airflow around the VTX.
- Consider reducing power output if not needed.
- Verify the VTX is not short-circuited.
- Cannot Change Settings:
- If using buttons, ensure you are pressing them correctly (short vs. long press).
- If using OSD control, verify SmartAudio/TrampHV is correctly configured in your flight controller firmware and wiring.
9. User Tips
- Heat Management: For optimal performance and longevity, especially when operating at 1.6W, ensure the VTX has excellent airflow. Mounting it in a location with direct prop wash can significantly help.
- Antenna Choice: While a linear brass antenna is included, consider upgrading to a high-quality circular polarized antenna for improved signal penetration and reduced multipathing in complex environments.
- SmartAudio/TrampHV: Utilizing the SmartAudio or TrampHV feature through your flight controller is highly recommended for convenient channel and power changes without needing to access the VTX directly.
- Power Output: Always use the lowest power output necessary for your flight conditions to minimize heat generation and reduce interference with other FPV pilots.
10. Warranty and Support
HGLRC provides support for its products. If you encounter product problems, please contact the seller or manufacturer directly. Be prepared to provide product pictures or videos to assist with troubleshooting and support requests.