CKPSMS KP-19356

Contents

Instruction Manual

CKPSMS KP-19356 Upper and Lower Knife Set for Singer S0230 S0235 Serger Overlock Machines

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the CKPSMS KP-19356 Upper and Lower Knife Set. This set is designed as a replacement part for specific Singer Serger Overlock Machines, ensuring precise cutting performance for your sewing projects.

2. Product Components

The KP-19356 set includes the following components:

  • 1 x Upper Knife
  • 1 x Lower Knife

The knives are made of high-quality steel, designed for durability and sharp cutting.

Upper and Lower Knife Set for Serger Machine
Figure 1: The CKPSMS KP-19356 Upper and Lower Knife Set.

3. Specifications

FeatureDetail
Part NumberKP-19356
Part NameBlade Knife Upper & Lower Set
MaterialSteel
Set TypeYes
UseHousehold use
TypeSewing machine parts
Lower Knife Length31.2 mm
Lower Knife Width8 mm
Upper Knife Length36.5 mm
Upper Knife Width7.9 mm

Notice: Please pay attention to the size of the product to ensure compatibility with your machine.

Lower Knife dimensions: 31.2mm length, 8mm width
Figure 2: Dimensions of the Lower Knife.
Upper Knife dimensions: 36.5mm length, 7.9mm width
Figure 3: Dimensions of the Upper Knife.

4. Compatibility

This high-quality Steel Blade Knife Upper & Lower Set replacement is exactly compatible with the following serger overlock sewing machines:

  • Singer S0230
  • Singer S0235

5. Installation Instructions

Replacing the knives on your serger machine requires careful attention. Always refer to your specific sewing machine's manual for detailed instructions. The following are general steps:

  1. Safety First: Turn off and unplug your serger machine from the power outlet before beginning any maintenance or part replacement.
  2. Access the Knife Area: Raise the presser foot and open the front and/or side covers of your serger to access the knife mechanism.
  3. Identify Knives: Locate the upper and lower knives. The upper knife typically moves up and down, while the lower knife remains stationary or moves slightly.
  4. Remove Old Knives: Using the appropriate screwdriver (usually a small flathead or hex key, often included with your serger), carefully loosen the screws holding the old knives in place. Remove the old knives. Be cautious as they may still be sharp.
  5. Clean the Area: Use a small brush or lint-free cloth to clean any lint, dust, or debris from the knife area.
  6. Install New Lower Knife: Position the new lower knife (Figure 2) into its slot. Ensure it is seated correctly and tighten its screw(s) securely, but do not overtighten.
  7. Install New Upper Knife: Position the new upper knife (Figure 3) into its slot. Ensure it is seated correctly and tighten its screw(s) securely.
  8. Adjust Knife Position (if necessary): The knives must meet and overlap correctly to cut fabric cleanly. Consult your serger's manual for specific knife alignment procedures. Generally, the upper knife should pass just to the left of the lower knife, with a slight overlap.
  9. Test Cut: Close the machine covers, plug in the machine, and perform a test cut on a scrap piece of fabric to ensure the knives are cutting cleanly and smoothly. Adjust alignment if needed.

6. Operating the Knives

Once installed, the upper and lower knives work in conjunction to trim the fabric edge precisely before the stitches are formed. Ensure that the knives are sharp and correctly aligned for optimal performance. Dull or misaligned knives can lead to frayed edges, skipped stitches, or fabric damage.

7. Maintenance

Proper maintenance of your serger knives will extend their lifespan and ensure consistent sewing quality:

  • Regular Cleaning: After each sewing session, use a small brush to remove lint and thread fragments from around the knife area. Accumulated debris can hinder knife movement and cutting efficiency.
  • Inspection: Periodically inspect the knives for signs of dullness, nicks, or damage. A dull knife will result in ragged fabric edges.
  • Replacement: Knives are wear-and-tear parts. Replace them when they become dull or damaged, typically after many hours of use or if you notice a decline in cutting quality. The frequency depends on the type of fabric sewn and usage intensity.
  • Storage: When not in use, ensure the machine is covered to prevent dust accumulation, which can affect all moving parts, including the knives.

8. Troubleshooting

If you encounter issues related to cutting performance after installing new knives, consider the following:

ProblemPossible CauseSolution
Fabric edges are frayed or not cut cleanlyKnives are dull or misaligned.Ensure knives are sharp. Re-check knife alignment according to your serger's manual.
Knives are not moving freelyLint or debris accumulation.Clean the knife area thoroughly.
Knives are hitting each other or not cutting at allIncorrect installation or severe misalignment.Turn off and unplug the machine. Re-install knives carefully, ensuring correct seating and alignment. Consult your serger manual.

9. Technical Support

For technical assistance or if you have questions regarding the compatibility or installation of these parts:

  • If you are unsure if these parts are compatible with your machine, please send a message via AliExpress. Our technicians will provide professional and accurate advice.
  • Do not hesitate to contact us if you encounter any issues using the received parts.
  • When seeking technical support, please provide your machine brand and complete model number for the most accurate assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.