Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Flipsky Mini FSESC6.8 Plus Electronic Speed Controller. This high-performance, IP68 waterproof ESC is designed for demanding applications such as efoils, ejets, and electric surfboards, offering robust control and protection features.

Specifications
| Feature | Detail |
|---|---|
| Firmware | 5.2 (supports firmware upgrade) |
| Continuous Current | 150A |
| Instantaneous Current | 200A (depends on mounting and ambient temperature) |
| Voltage Range | 14V-60V (4-13S Cells, safe for 4S to 12S; voltage spikes must not exceed 60V) |
| BEC | 5V@1.5A |
| ERPM | 150000 |
| Supported Sensors | Sensorless |
| Supported Modes | BLDC, FOC (sinusoidal) |
| Control Interface Ports | USB, UART |
| Input Set Support | PPM, ADC, NRF, UART |
| Regenerative Capacity | Yes |
| Programmable | Yes |
| Power Wire | 8AWG 1200mm |
| Motor Wire | 8AWG 170mm |
| Dimensions | 103.5mm x 67.6mm x 27.5mm (including aluminum case) |

Key Features
- IP68 Waterproof Rating: Fully sealed design ensures protection against water ingress, making it suitable for marine and wet environments.
- VESC Based: Utilizes the VESC6 platform, allowing for advanced configuration and real-time data monitoring via VESC_TOOL software.
- High Current Capacity: Features a 6-layer 3oz special PCB plate for excellent heat dissipation, supporting a rated continuous current of 150 Amps.
- Powerful Processor: Equipped with a STM32F405 CPU (ARM Cortex-M4 structure) for high clock speed and efficient processing.
- Versatile Control Modes: Supports Current, Dutycycle, and Speed control modes to suit various application requirements.
- Comprehensive Protection: Includes multiple safety features such as low voltage protection, high voltage protection, over-current protection, abnormal temperature protection, and MOSFET over-temperature protection (above 80℃).
- Compact Design: Efficiently packaged in a compact size (103.5x67.6x27.5mm) for easy integration into various setups.
Setup and Wiring
Proper wiring is crucial for the safe and efficient operation of your ESC. Refer to the wiring diagram below for connection details. Ensure all connections are secure and insulated to prevent short circuits.

Connection Points:
- Battery Connection (B+, B-): Connect the positive (B+) and negative (B-) terminals of your battery to the corresponding inputs on the ESC. Ensure correct polarity.
- Motor Connection (A, B, C): Connect the three phase wires from your motor to the A, B, and C outputs on the ESC. The order may affect motor direction, which can be adjusted in software if needed.
- UART Port (1): Used for communication with external devices such as Bluetooth modules or other accessories.
- ADC Port (2): Analog-to-Digital Converter port, typically used for analog input devices like throttles.
- PPM Port (3): Pulse Position Modulation port, commonly used for connecting standard RC receivers.
- USB Port (4): Connect to a computer using the provided USB cable for configuration and firmware updates via VESC_TOOL.

Important: Always double-check all connections before applying power to avoid damage to the ESC or other components.
Operating Instructions
The Flipsky Mini FSESC6.8 Plus is programmable via the VESC_TOOL software. This tool allows for comprehensive configuration and real-time monitoring of the ESC.
Initial Configuration with VESC_TOOL:
- Download and install the latest VESC_TOOL software from the official VESC project website.
- Connect the ESC to your computer using the USB cable.
- Launch VESC_TOOL and establish a connection to the ESC.
- Perform the motor detection wizard to configure motor parameters.
- Configure input settings (PPM, ADC, UART) according to your remote control or input device.
- Adjust protection limits (voltage, current, temperature) to match your battery and motor specifications. Pay close attention to the voltage limits (4S to 12S safe, spikes not exceeding 60V).
- Save all configurations to the ESC.
Control Modes:
- Current Control: Provides direct control over the motor current, offering precise torque control.
- Dutycycle Control: Controls the motor by setting the PWM duty cycle, suitable for basic speed control.
- Speed Control (FOC): Utilizes Field-Oriented Control for smooth and efficient speed regulation.
Select the appropriate control mode based on your application and desired performance characteristics within the VESC_TOOL.
Maintenance
The Flipsky Mini FSESC6.8 Plus is designed for durability, especially with its IP68 waterproof rating. However, regular checks can extend its lifespan and ensure optimal performance.
- Visual Inspection: Periodically inspect the ESC and its wiring for any signs of physical damage, corrosion, or loose connections.
- Cleaning: After use in wet or dirty environments, rinse the ESC with fresh water to remove salt, sand, or debris. Ensure it is completely dry before storage or next use.
- Firmware Updates: Keep the ESC firmware updated to the latest version (currently 5.2) using VESC_TOOL to benefit from performance improvements and bug fixes.
- Temperature Monitoring: While the ESC has over-temperature protection, monitoring its operating temperature during demanding use can help identify potential issues with cooling or excessive load.
Troubleshooting
Here are some common issues and their potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor not spinning / No response | Loose connections, incorrect wiring, incorrect VESC_TOOL configuration, low battery voltage. | Check all wiring (battery, motor, input signal). Verify VESC_TOOL settings, especially motor detection and input setup. Charge battery. |
| ESC cuts out during operation | Over-current, over-voltage, under-voltage, or over-temperature protection triggered. | Check VESC_TOOL fault codes. Ensure battery voltage is within limits. Reduce load. Improve cooling. Adjust protection thresholds carefully if necessary. |
| Motor spins in wrong direction | Incorrect motor phase wire connection. | Swap any two of the motor phase wires (A, B, C) or reverse motor direction in VESC_TOOL. |
| Difficulty connecting to VESC_TOOL | Incorrect USB driver, faulty USB cable, ESC not powered on. | Ensure ESC is powered. Try a different USB port/cable. Reinstall VESC_TOOL drivers. |
If troubleshooting steps do not resolve the issue, contact customer support.
User Tips
No specific user tips were available from customer reviews or Q&A for this product at the time of manual creation. However, general best practices for ESCs include:
- Always use appropriate connectors for high-current applications to minimize resistance and heat.
- Ensure adequate ventilation or cooling for the ESC, even with its waterproof rating, especially during prolonged high-power usage.
- Regularly check battery health and voltage to prevent under-voltage cutoffs or damage.
Warranty and Support
Warranty Policy:
The warranty period for consumable electronic products, including VESC, motors, and batteries, is 2 months from the 7th day after shipment (shipping date checked by logistic record).
For non-electronic products, the warranty period is also 2 months from the 7th day after shipment.
If a product is found to be defective within the warranty period, you may return it for repair or replacement. The cost of shipping for return and replacement is typically borne by the customer.
Conditions Not Covered by Warranty:
- Lack of proof of purchase channel.
- Mechanical damage to electronic components or PCB.
- PCB board has repair soldering iron traces (excluding soldering the cable bullet connectors).
- Water damage or external impact damage (for non-waterproof products; for IP68 rated products, water ingress due to improper sealing or extreme conditions beyond specifications may not be covered).
- Products purchased from channels other than the official Flipsky store.
- Warranty is invalid if the product is resold (second transaction).
Clarification: All products are tested before shipment. Incorrect mounting or information for VESC/motor settings is not covered by warranty. Shipping costs for warranty service are the responsibility of the customer.
Customer Support:
For any issues or support inquiries, please contact Flipsky service at: flipsky_service@outlook.com
When contacting support, please provide your original source order number or personal card number (for group buy products) to facilitate faster service.