1. Introduction
The Flipsky Mini V6.8 PLUS is a high-performance electronic speed controller (ESC) designed for various electric mobility applications such as electric skateboards, ebikes, scooters, and robots. Based on the VESC platform, it offers advanced control capabilities and robust protection features. This manual provides essential information for the safe and effective use of your controller.
2. Safety Guidelines
Please read and understand all safety instructions before operating the controller. Failure to follow these guidelines may result in property damage, personal injury, or voiding the warranty.
- Always ensure proper insulation for all electrical connections to prevent short circuits.
- Verify that the battery voltage is within the specified range (4-12S, max 60V) to avoid over-voltage damage.
- Avoid exposing the controller to moisture, water, or extreme temperatures.
- Ensure adequate airflow around the controller for proper heat dissipation, especially during high-current operation.
- Do not attempt to modify the controller's hardware or firmware unless explicitly instructed by Flipsky support.
- Always disconnect the battery before performing any maintenance or wiring changes.
3. Package Contents
Upon opening your package, please verify that all the following items are included:
- 1x Flipsky Mini V6.8 PLUS Controller
- 1x USB Cable
- Sensor Wires (various types, e.g., Hall sensor wires)
- 8.0mm Bullet Connectors (female, 2 for power, 3 for motor)
- Heat Shrink Tubing
4. Specifications
| Parameter | Value |
|---|---|
| Firmware | 5.2 (supporting firmware upgrade) |
| Continuous Current | 150A |
| Instantaneous Current | 200A (values depend on mounting and ambient temperature) |
| Voltage Range | 14V-60V (4-13S, safe for 4S to 12S; voltage spikes must not exceed 60V) |
| BEC | 5V@1.5A |
| ERPM | 150000 |
| Supported Sensors | ABI, HALL, AS5047, AS5048A |
| Supported Modes | BLDC, FOC (sinusoidal) |
| Control Interface Ports | USB, CAN, UART, IIC |
| Input Set Support | PPM, ADC, NRF, UART |
| Regenerative Capacity | Yes |
| Programmable | Yes |
| Power Wire | 8.0mm bullets female X 2pcs |
| Motor Wire | 8.0mm bullets female X 3pcs |
| Dimensions | 92.7 x 68 x 31.5mm (Including aluminum case) |
5. Key Features
- VESC6 Based: Programmable via VESC_TOOL and supports real-time data reading.
- High-Performance CPU: Adopts STM32F405 ARM Cortex-M4 CPU for fast clock speed.
- Multiple Control Modes: Supports Current, Dutycycle, and Speed control modes.
- Comprehensive Protection: Includes low voltage, high voltage, over-current, temperature abnormality, and MOSFET over-temperature protection.
- IMU Module Support: Connect an IMU module (e.g., MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160) via the IIC interface for balancing car functionality.
6. Setup and Wiring
Proper wiring is crucial for the safe and correct operation of your controller. Refer to the wiring diagram below for connections.
Connection Points:
- Battery (B+, B-): Connect your battery pack to the B+ (positive) and B- (negative) terminals. Ensure correct polarity. The controller supports 4-12S LiPo batteries.
- Motor (A, B, C): Connect your brushless motor's phase wires to the A, B, and C terminals.
- COMM (1): Communication port.
- PPM (2): Pulse Position Modulation input for throttle control (e.g., from a remote receiver).
- CAN (3): Controller Area Network bus for multi-controller setups or external devices.
- HALL (4): Hall sensor input for sensored motor operation.
- USB (5): Connect to a computer for configuration and firmware updates using VESC_TOOL.
After physical connections, use the VESC_TOOL software to configure motor parameters, input settings, and safety limits according to your specific application.
7. Operating the Controller
The Flipsky Mini V6.8 PLUS controller is highly configurable via the VESC_TOOL software. This tool allows you to:
- Motor Setup Wizard: Automatically detect and configure your motor parameters.
- Control Modes: Select between Current, Dutycycle, or Speed control modes based on your application's requirements.
- Input Configuration: Set up your input device (PPM, ADC, NRF, UART) for throttle and braking.
- Real-time Data: Monitor motor RPM, current, voltage, temperature, and other parameters in real-time.
- Firmware Updates: Keep your controller up-to-date with the latest firmware for improved performance and features.
Always perform initial tests at low power and with the driven wheels off the ground to ensure safe operation and correct configuration.
8. Maintenance
To ensure the longevity and optimal performance of your Flipsky Mini V6.8 PLUS controller, follow these maintenance guidelines:
- Keep Clean: Regularly inspect the controller for dirt, dust, or debris. Clean with a soft, dry brush or compressed air.
- Avoid Moisture: Protect the controller from water and high humidity. If it gets wet, ensure it is completely dry before re-applying power.
- Check Connections: Periodically inspect all wiring connections for looseness, corrosion, or damage. Secure any loose connections.
- Thermal Management: Ensure the aluminum case is free from obstructions and has adequate airflow to dissipate heat effectively.
- Firmware Updates: Check for and install official firmware updates from Flipsky to benefit from bug fixes and new features.
9. Troubleshooting
If you encounter issues with your controller, consider the following common problems and solutions:
| Problem | Possible Cause / Solution |
|---|---|
| Controller not powering on | Check battery connection and voltage. Ensure power wires are securely connected and not damaged. |
| Motor not spinning or erratic behavior | Verify motor phase wire connections (A, B, C). Check Hall sensor connections if using sensored mode. Re-run motor detection in VESC_TOOL. |
| Controller shuts down during operation | Could be due to low voltage protection (battery depleted), high voltage protection (voltage spikes), over-current protection, or MOSFET over-temperature protection. Check battery state, wiring, and ensure adequate cooling. |
| No response from input device (PPM, etc.) | Check input device wiring and ensure it's correctly configured in VESC_TOOL. |
| Connection issues with VESC_TOOL | Ensure USB cable is properly connected. Try a different USB port or cable. Verify correct drivers are installed. |
| Unusual noises or vibrations from motor | Re-check motor detection and configuration in VESC_TOOL. Inspect motor for physical damage. |
If issues persist, consult the VESC community forums or contact Flipsky support.
10. User Tips
- Start Conservative: When first setting up, use conservative current limits and acceleration settings in VESC_TOOL to prevent unexpected behavior.
- Monitor Temperatures: Especially in demanding applications, regularly monitor the controller's temperature. If it consistently runs hot, consider additional cooling or reducing load.
- Secure Wiring: Use cable ties and heat shrink to secure all wires, preventing them from vibrating loose or getting damaged during operation.
- Regular Checks: Before each use, quickly check all connections and ensure no visible damage to the controller or wiring.
- Backup Settings: After successfully configuring your controller, save your VESC_TOOL settings profile. This will save time if you ever need to reflash firmware or troubleshoot.
11. Warranty and Support
Flipsky offers a warranty for its products. Please review the following policy details:
Warranty Period:
- Consumable Electronic Products (e.g., VESC/Motor/Battery): Guaranteed for 2 months from the 7th day after shipment (shipping date checked by logistic record).
- Non-Electronic Products: Guaranteed for 2 months from the 7th day after shipment (shipping date checked by logistic record).
Warranty Conditions:
The warranty covers manufacturing defects. If a product is found to be defective within the warranty period, Flipsky will repair or replace it. Shipping costs for returns may apply.
Conditions that Void Warranty:
The warranty will be voided under the following circumstances:
- Mechanical damage to electronic components or PCB.
- PCB board has repair soldering iron traces (excluding soldering the cable bullet connectors).
- Wire damage or external impact damage.
- Water inflow or moisture damage.
- Abnormal applications beyond the product specifications.
- Products purchased not directly from Flipsky.net or an authorized channel.
- Any modifications or unauthorized repairs.
For warranty claims or technical support, please contact Flipsky support at: service@outlook.com. Please provide your original source order number or warranty card number (if applicable) for verification.