Flipsky Mini FSESC4.20

Contents

Flipsky Mini FSESC4.20 50A Electric Speed Controller User Manual

For Skateboard Base On VESC® 4.12 With Aluminum Anodized Heat Sink

1. Introduction

This manual provides essential information for the safe and efficient use of your Flipsky Mini FSESC4.20 50A Electric Speed Controller. Please read this manual thoroughly before installation and operation to ensure optimal performance and longevity of the device.

2. Package Contents

Upon opening your package, please verify that all the following items are included:

  • 1 x Mini FSESC4.20 with Heatsink
  • 1 x Micro USB Cable
  • 1 x VESC Sensor Wire
  • 1 x User Manual (this document)
Package contents of Flipsky Mini FSESC4.20 including the ESC, USB cable, sensor wire, and manual.

Figure 2.1: Contents of the Flipsky Mini FSESC4.20 package.

3. Product Overview

The Flipsky Mini FSESC4.20 is a compact and powerful Electric Speed Controller designed for electric skateboards and similar applications. It features an aluminum anodized heatsink for efficient heat dissipation and is based on the VESC® 4.12 hardware platform.

Top view of the Flipsky Mini FSESC4.20 showing the circuit board, capacitors, and connectors.

Figure 3.1: Top view of the Mini FSESC4.20.

Bottom view of the Flipsky Mini FSESC4.20 showing the heatsink.

Figure 3.2: Bottom view with heatsink.

Top view of the Flipsky Mini FSESC4.20 with dimensions labeled: 67mm length, 39mm width, 18.3mm height (including heatsink).

Figure 3.3: Dimensions of the Mini FSESC4.20.

4. Setup and Wiring

Proper wiring is crucial for the safe and correct operation of the ESC. Please follow the diagrams carefully.

4.1. Basic Connections

Connect the ESC to your battery, motor, and receiver as shown in the diagram below. Ensure correct polarity for the battery connection to prevent damage.

Basic wiring diagram showing connections for Battery, Motor, and Receiver (GND, 5V, SIN) to the ESC.

Figure 4.1: Basic wiring connections.

4.2. Detailed Port Pinouts

The Mini FSESC4.20 provides various ports for advanced functionality and configuration. Refer to the detailed diagram for pin assignments.

Detailed wiring diagram showing pinouts for CAN, SENSE, COMM, SWD, USB, ADC, HALL, and receiver connections.

Figure 4.2: Detailed port pinouts and connections.

  • 1. CAN: For communication with other VESC-compatible devices.
  • 2. SENSE: Sensor port for motor feedback.
  • 3. COMM: Communication port, includes ADC, TX/SCL, RX/SDA, ADC2.
  • 4. SWD: Debugging port.
  • 5. USB: Micro USB port for configuration and firmware updates via VESC Tool.
  • ADC Port: 3.3V, GND, ADC.
  • HALL Sensor Port: 5.5V, 3.3V, ADC, TX/SCL, RX/SDA, ADC2.
  • HALL Sensor Pinout: 5V, TMP, H1, H2, H3, GND, HALL, AS5047 ABI.

4.3. Initial Configuration

After wiring, connect the ESC to a computer using the Micro USB cable. Use the VESC Tool software (available from VESC Project website) to configure motor parameters, battery limits, and control modes. Perform motor detection for optimal performance.

5. Operating Instructions

The Flipsky Mini FSESC4.20 is designed for precise control of brushless DC motors. Once configured with VESC Tool, its operation is typically managed by your remote control system.

  • Power On: Connect the battery to the ESC. The ESC will typically emit a series of beeps indicating it's ready.
  • Throttle Control: Use your remote control to apply throttle. The ESC will translate the input into motor speed.
  • Braking: Apply reverse throttle on your remote for regenerative braking.
  • Safety: Always ensure your motor and battery are securely connected before operation. Avoid operating in wet conditions unless the ESC is properly waterproofed.

6. Maintenance

To ensure the longevity and reliable performance of your ESC, follow these maintenance guidelines:

  • Regular Inspection: Periodically check all wiring connections for looseness or damage.
  • Cleanliness: Keep the ESC free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning.
  • Heat Management: Ensure the heatsink is clear of obstructions to allow for proper airflow. Overheating can severely damage the ESC.
  • Firmware Updates: Check for official firmware updates periodically using the VESC Tool to benefit from performance improvements and bug fixes.

7. Troubleshooting

If you encounter issues with your Flipsky Mini FSESC4.20, consider the following common problems and solutions:

  • Motor Not Spinning:
    • Check all motor and battery connections.
    • Verify battery charge level.
    • Ensure the remote control is paired and functioning.
    • Re-run motor detection in VESC Tool.
  • Erratic Motor Behavior:
    • Check sensor wire connections if using sensored mode.
    • Ensure motor detection was successful and parameters are correctly set.
    • Inspect for any loose wires or interference.
  • ESC Overheating:
    • Ensure adequate airflow around the heatsink.
    • Check motor current limits in VESC Tool; they might be set too high for your motor/setup.
    • Verify that the motor is not overloaded.
  • No Power/LEDs Off:
    • Check battery voltage and connection to the ESC.
    • Inspect for any visible damage to the ESC or power cables.

For persistent issues, consult online VESC communities or contact Flipsky support.

8. Specifications

Feature Specification
Hardware VersionV4.20
FirmwareLatest Version (VESC compatible)
Continuous Amps50A
Peak Amps150A
Cells (LiPo)3-13S
Voltage Range8V-60V
BEC Output5V@1.5A
BEC TypeInternal driver support
TimingSoftware calibration
Cutoff VoltageProgrammable
FrequencyPWM input
GovernorNo
Weight80g
PCB Size39 x 46 x 17.4mm
Overall Dimensions (with Heatsink)67 x 39 x 18.3mm
Programming Card SupportNo (uses VESC Tool)
Reverse FunctionYes
Motor Wire Gauge12 AWG
Power Cable Gauge12 AWG
MaterialMetal (Heatsink)
Recommended Age14+ years
ApplicationVehicles & Remote Control Toys

9. User Tips

  • VESC Tool: Always use the latest version of VESC Tool for configuration and firmware updates to ensure compatibility and access to new features.
  • Cable Management: Secure all wires to prevent them from rubbing, snagging, or coming loose during operation.
  • Testing: Before full-scale use, perform bench testing with reduced power to verify all settings and connections are correct.
  • Battery Safety: Always use batteries within the specified voltage range (3-13S LiPo) and ensure they are in good condition.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.