1. Introduction
Thank you for purchasing the HOTA T8 Smart Balance Charger. This manual provides detailed instructions for the safe and effective use of your charger. Please read it carefully before operation and keep it in a safe place for future reference. A PDF version of this manual is available at this link.
The HOTA T8 is a powerful and compact smart charger and checker designed for various battery types, including LiPo, LiHv, LiFe, Lilon, Lixx, LTO, NiZn, NiCd, NiMH, PB, and Eneloop. It features a 2.8-inch IPS display, automated fan speed control, and multiple protection mechanisms to ensure safe and efficient charging.
Product overview video showcasing the HOTA T8 Smart Balance Charger.
2. Safety Notes and Warnings
WARNING! FIRE HAZARD! NEVER USE CHARGER UNSUPERVISED!
- Do not use the charger in an unattended manner. In case of any functional abnormality, stop using it and refer to this manual.
- Keep the charger away from dust, humidity, rain, and high temperatures. Avoid direct exposure to sun and intense vibration.
- Ensure the input voltage (6.5-30V DC) matches the charger's operating voltage range.
- Place the charger on a heat-resisting, non-flammable, and insulating surface. Keep inflammable and explosive objects away from operation areas.
- Ensure the heat emission hole and cooling fan are uncovered and clear for smooth heat extraction.
- Fully understand battery charging/discharging characteristics and specifications. Incorrect parameter settings can damage the charger/battery or lead to fire/explosion.
- When charging/discharging is complete, press the Exit key to terminate the task and remove the battery when the charger shows the standby screen.
- Do not modify or disassemble the charger.
- Do not place the charger or battery near flammable objects or on surfaces like carpet, paper, plastic, vinyl, leather, wood, or inside aircraft models/cars during use.
- Do not place the charger within reach of children.
- Do not drop wires or other conductive objects into the charger.
- Ensure the correct battery type and parameters are selected. Incorrect selection can damage the battery or be dangerous (e.g., overcharging lithium batteries can cause fire).
- Do not mix batteries of different types, capacities, or manufacturers.
- Do not attempt to charge non-rechargeable dry batteries.
- Do not charge or discharge if the battery leaks, swells, peels, changes color, or is deformed.
- Do not exceed the maximum charge limit specified by the battery manufacturer.
- Carefully follow the battery manufacturer's instructions and safety advice.
- Do not cover the fan outlet. Avoid direct sunlight, confined spaces, or high-temperature environments, as this may activate temperature protection and prevent normal operation.
The electronic products with this mark must be disposed of separately from household waste. Take it to a garbage collection center for classification.
3. Setup
3.1 Product Overview and Ports
Familiarize yourself with the various ports and controls on your HOTA T8 charger:

Front view of the HOTA T8 Smart Balance Charger, highlighting the display and control buttons.

The HOTA T8 features a simple and efficient user interface for easy operation.

Labeled diagram of the HOTA T8 Smart Balance Charger, showing the Speed Shuttle Key, Exit Key/Multi-Function Key, Output Port, Balance Port, Multi-Function Port, USB Port 5V/Update Port, DC in Port, and Fan.
- Speed Shuttle Key: Used for navigation and selection.
- Exit Key/Multi-Function Key: Used to exit menus or perform multi-functions.
- Output Port: Main port for connecting batteries for charging/discharging (XT60 connector).
- Balance Port: For connecting battery balance leads (1S-8S).
- Multi-Function Port: Can be used to test RC airplane control servos, receivers, or RF transmitters.
- USB Port 5V/Update Port: For 5V/2.1A USB output and firmware updates.
- DC in Port: For connecting the power supply (7.0-35.0V DC).
- Fan: Integrated cooling fan for temperature control.
3.2 Recommended Connection Method
- Connect the power supply to the charger's DC input port. Wait for the system to complete its self-checking.
- Connect the battery to the charger under the standby interface.
- Set up task parameters applicable to your battery through the display and touch key.
- Begin operation.

Example connection of a LiPo 8S battery to the HOTA T8 charger, showing both the main output and balance port connections.
3.3 Balance Port Connection Notes
The detection balance port is suitable for lithium battery packs. When connecting the battery, ensure it is aligned with the "-" sign as shown in the diagram.

Detailed diagram illustrating the correct alignment and connection of a lithium battery's balance plug to the HOTA T8 charger's balance port.
3.4 Multi-Function Port Usage
The charger has two multi-function ports that can be used for various testing purposes:
- Connect to RC airplane control servos.
- Connect to RC airplane receivers or RF transmitters.

Diagram showing how to connect an RC airplane control servo and an RC airplane receiver/RF transmitter to the multi-function ports of the HOTA T8 charger.
4. Operating Instructions
4.1 How to Confirm Charging Current
It is crucial to know the maximum charging current of your battery. Excessive current can shorten battery lifespan, cause damage, or lead to heating/explosion during charging.
- Battery charging/discharging capacity is usually marked with a 'C' value. Maximum charging current = C value × Battery capacity. For example, a 1000mAh battery with a 5C charging capacity has a maximum charging current of 1000mAh * 5 = 5000mA (5A).
- For lithium batteries, if the supported charging C value is unknown, set the charging current below 1C for safety.
- Reference relation between C value and charging time: Charging time ≥ 60 minutes / charging C value (approx. 60-70 minutes for 1C). Actual time may vary due to battery conversion efficiency.
4.2 Operative Skills
- Connect the power supply to the DC port. After self-checking, connect the battery. Short press the Speed Shuttle key to open "Task Settings". Use Up/Down to select the task and adjust parameters. Short press Speed Shuttle to start.
- During task execution, short press Speed Shuttle to open "Adjust Task" to modify current or stop. Long press Speed Shuttle to quickly end the task.
- In standby, long press Speed Shuttle to enter "Charger Settings".
4.3 Working Parameters Display
The HOTA T8 features a clear display to show various working parameters and statuses.
4.3.1 Standby Mode
In standby mode, the output current, output power, charged capacity, and operation time are all zero. You can scroll the Speed Shuttle key to switch display information (cell voltage, operating data).

The HOTA T8 display in Standby mode, showing zero current, power, and capacity, awaiting task selection.
4.3.2 Power Supply Mode
When "Power supply" task is selected, the charger acts as an adjustable power supply. Information displayed includes input voltage, operating temperature, and charged times.

The HOTA T8 display in Power Supply mode, showing current, power, voltage, temperature, and charged times.
Note: The output port voltage can be set between 1V and 35V, and output power between 20W and 650W. Ensure output wires are not short-circuited and avoid overloading.
4.3.3 Charging Mode
When charging, the screen is marked in orange. It turns green when charging is completed (cell voltage difference < 20mV) and blue when fully balanced (cell voltage difference < 10mV).

The HOTA T8 display during a charging task, showing current, power, total voltage, and individual cell voltages.
Scroll the Speed Shuttle key to view cell voltage, internal resistance, and operating data. Internal resistance is only displayed during valid measurement in balance charging mode.
4.3.4 Discharging Mode
The discharge function allows you to discharge the battery. It is recommended to connect the balance port for faster and more accurate discharge termination detection.

The HOTA T8 display during a discharging task, showing negative current, power, total voltage, and individual cell voltages.
Note: Due to internal discharge power limitations, the process may be slower.
4.3.5 External Discharging Mode
This mode uses an external high-power load resistor for faster and more accurate discharge. Connect the battery to be discharged to the input port, and the load resistor to the output port. Recommended load resistance is 1.5-2.5 ohms.

The HOTA T8 display during an external discharging task, showing negative current, power, total voltage, and individual cell voltages.

Diagram illustrating the setup for external discharge, connecting the battery to the input port, the charger, and an external load resistor to the output port.
Caution: The load resistor can become very hot during external discharge. Pay attention to safety to avoid accidents or personal injury.
4.3.6 Regenerative Discharge Mode
The HOTA T8 supports regenerative discharge up to 650W, returning power from the discharge battery to an input battery. Connect the battery to receive power to the charger's input port, and the discharge battery to the output port. Set the task to "regeneration discharge".

The HOTA T8 display during a regenerative discharge task, showing negative current, power, total voltage, and individual cell voltages.
Note: For lithium batteries, it is strongly recommended to connect the balance port for balanced discharge. When setting the input cut-off voltage, set it to the highest protection voltage of the power supply to prevent damage.
4.3.7 Storage Mode
This function charges or discharges the battery to a preset storage voltage. If the battery voltage is lower than the preset, it charges; if higher, it discharges. This mode does not precisely balance cell voltage to save time.

The HOTA T8 display during a storage discharging task, showing negative current, power, total voltage, and individual cell voltages.
4.3.8 Balancing Mode
The balance function equalizes the voltage of individual cells in a battery pack. The balance time depends on the cell voltage difference and target voltage. The charger automatically sets the initial balance voltage, which can be adjusted.

The HOTA T8 display during a balancing task, showing current, power, total voltage, and individual cell voltages.
4.3.9 Cycle Charging Mode
This mode is used for cycling NiCd, NiMH, or Eneloop batteries. It performs a charge-discharge cycle multiple times. Connect the battery and select "ReGen. Discharge" as the task.

The HOTA T8 display during a cycle charging task for NiMH batteries, showing current, power, voltage, and cycle progress.
4.4 Charger Settings
Long press the Speed Shuttle key in standby mode to access the "Charger Settings" menu. This menu allows configuration of various parameters.
| Setting | Description |
|---|---|
| Input settings | Adjust input source, type, maximum power, maximum current, and minimum voltage. |
| Task parameters | Adjust Safety Timer, Max Capacity, End Current, and other task-specific parameters. |
| System parameters | Adjust Language, Regenerative Discharge settings, input power, Volume, and other system-wide parameters. |
| Calibration | For data calibration. |
| System self-checking | Start self-checking of the charger. |
| Factory settings | Restore all parameters to factory settings (User calibration data cleanup). |
| System info | Display system information, serial number. |
| Back | Exit "Charger Settings". |
4.4.1 Input Settings
In "Charger Settings", select "Input settings" to configure input parameters:
- Input selection: On or Off for charging.
- Input source: Choose between Source1, Source2, Source3, Source4.
- Input type: Adapter or Battery.
- Max. power: Settings for maximum input power.
- Max. current: Settings for maximum input current.
- Min. voltage: Settings for maximum input voltage.
4.4.2 Task Parameters
In "Charger Settings", select "Task parameters" to configure task-specific settings:
- Safety timer: Sets maximum running time; automatic protection stops the task if exceeded.
- Max. capacity: Sets maximum charging capacity; automatic protection stops the task if exceeded.
- Safety Inter. Temp.: Settings for internal safety temperature.
- Safety Exter. Temp.: Settings for external safety temperature.
- End current: Cut off when the current is less than the ratio between task completed current and set up current.
- Balance start Vol.: Settings for the initial voltage of Balancing.
- Trickle charge: Whether to turn on Trickle Charge: On or Off.
- Continue charge: Whether to turn on Continuous charge: On or Off.
- Task storage: Whether to turn on Storage task: On or Off.
4.4.3 System Parameters
In "Charger Settings", select "System parameters" to configure system-wide settings:
- Language: System language setting (e.g., English).
- LCD backlight: Backlight adjustment: high, middle, low.
- Volume: Buzzer volume adjustment: high, middle, low (default OFF, operation sound blocked).
- Completion signal: Single or Repeat.
- Theme style: Theme style.
- Device name: Up or down button to choose letter, enter the device name manually, long press the O key to exit.
4.5 Task Settings
Short press the Speed Shuttle key in standby mode to open the "Task Settings" menu. Here you can select and configure different tasks:
| Setting | Description |
|---|---|
| Select task | Options: power, charging, discharging, storage charging, balancing, cycle charging. |
| Discharge mode | General discharging mode. |
| Battery type | LiHV, LiPo, Lilon, LiFe, LTO, LIXX, NiZn, PB, NiCd, NiMH, Eneloop. |
| Cell voltage | Fine tuning the full voltage of the cells. |
| -AV Detection | Can select the range 3mV-15mV. |
| Cell count | Select battery's strings: 1~8S. If balance port is inserted, it is automatically tested. |
| Charge current | Select current: charging/storage 0.1~22.0A, discharge 0.1-3.0A, external discharge 0.1-22.0A. |
| Cycle times | Select the times of cycling: 2-12. |
| Rest time | Select the time interval: 2Min-10Min. |
| Start task | Start to execute the task. |
| Back | Back to the upper menu. |
4.6 Tools
The HOTA T8 includes various tools for measurement and testing. Access them via "Charger Settings" -> "Tools".
| Tool | Description |
|---|---|
| Resistance Measurement | Tests the internal resistance of the connected battery. |
| PWM Measurement | Tests PWM signal frequency, duty cycle, and pulse width. |
| Servo ManuTest | Tests RC airplane control servo manually. |
| Servo AutoTest | Tests RC airplane control servo automatically. |
| PPM Measurement | Regulates PPM input signal of RC airplane receiver and changes output signal of its 8 channels. |
| PPM Out | Can change the parameters of the channels. |
| SBUS Measurement | Can switch to display the status of channels 1-8, 9-16. |
| SBUS Out | SBUS Output. |
| ESC test | Can set voltage and current for output power. |
5. Maintenance
5.1 Battery Activation and Repair
If a battery's cell voltage is below the pre-charging voltage at the start of a charging task, the charger will activate and repair it using one-tenth of the task setting current. Once the voltage rises above the pre-charging voltage, it will adjust to the set charging voltage. This protects over-discharged batteries.
5.2 Internal Resistance Measurement
The HOTA T8 can measure cell internal resistance during balanced charging tasks (effective after 2-3 minutes of charging). Internal resistance values are for comparative reference (e.g., judging cell consistency) and not for professional accuracy. Charging current magnitude influences accuracy; larger capacity/low internal resistance batteries require larger charging currents for accurate measurement.
5.3 General Care
- Keep the charger clean and free from dust and debris.
- Store the charger in a dry, cool place away from direct sunlight.
- Do not expose the charger to extreme temperatures or humidity.
- Regularly check all connections for wear or damage.
6. Troubleshooting
- Error during "System self-checking": If the output port is connected to a battery during self-checking, it will cause an error. Remove the battery, wait 5 seconds, and retry. Do not connect a battery to the DC input port during self-checking.
- Battery connection error: Re-plug the battery and ensure all connections are secure. Check battery interface metal parts for oxidation or burning that might affect contact.
- Charger not turning on: Ensure the power supply is correctly connected and within the specified voltage range (7.0-35.0V DC).
- Charger overheating: Ensure the fan outlet is not covered and the charger is in a well-ventilated area. Reduce charging current if necessary.
- Inaccurate readings: Ensure the charger is calibrated (if applicable) and that battery parameters are correctly set.
7. Specifications

Detailed specifications table for the HOTA T8 Smart Balance Charger.
| Parameter | Value |
|---|---|
| Input Voltage | DC 7.0~35.0V@MAX 27A |
| Charge Power | 0.1-22A@650W |
| Discharge Power | 0.1-22A@650W Recycle External, 0.1-3A@20W Normal mode |
| Balance Current | 1000mA@4.2V |
| Storage Temperature | -20~60°C |
| Operating Temperature | 0~40°C |
| Screen Size | 2.8" IPS 320×240 260000 colors |
| USB-A Output | 5V @ 2.1A Upgrade |
| Battery Type Support | Smart Battery/LiHv/LiPo/LiFe/Lilon/Lixx/LTO: 1~8S, NiZn/NiCd/NiMH: 1~20S, PB: 1~12S, Eneloop: 1~20S |
| Measurer PWM | 880us-2200us@20-400Hz |
| Measurer PPM | 880us-2200us*8CH@20-50Hz |
| Measurer SBUS | 880us-2200us*16CH@20-100Hz |
| Measurer Voltage | 1.0V-5.0V@1-8S |
| Measurer Internal resistance | 1-99mR@1-8S |
| Measurer ESC | 1-20A@1-35V MAX650W |
| Output PWM | 500us-2500us@20-1000Hz |
| Output PPM | 880us-2200us*8CH@50Hz |
| Output SBUS | 880us-2200us*16CH@74Hz |
| Output Power supply | 0.5-22A@1-35V mode: CC+CV |
| Dimensions | 97mm×69.5mm×34mm |
| Net Weight | 194g approximate |
| Protection Functions | Temperature protection, time protection, capacity protection, input reverse protection, output protection, short circuit protection, output overcurrent protection, output overvoltage protection, overcharge protection. |

Visual representation of the multiple protection features of the HOTA T8 charger, including short circuit, overheating, capacity, time, low voltage, overvoltage, overcurrent, and VO standard flame retardant material.
8. Warranty and Support
8.1 Warranty Information
The HOTA T8 Smart Balance Charger comes with a one-year warranty from the date of purchase. During this period, the product will be repaired free of charge for manufacturing defects.
Repairs are not free of charge if:
- Failure or damage is caused by improper use, disassembly, attachment, or modification not specified in the instructions.
- Failure or damage is caused by natural disasters, falls, collisions, or improper voltage.
For repairs outside the warranty period, a component and maintenance fee will apply.
8.2 Contact Information
For further inquiries, technical support, or warranty claims, please contact Shenzhen HOTA Technology Co., LTD. via:
- Website: www.hota-exp.com
- Tel: 0755-28180135
- E-mail: info@hota-exp.com
- Address: 213/215, Floor 2, Building 6, Monli Industrial Park, You Song Road., Longhua District, Shenzhen, China
9. User Tips
- XT150 Battery Connection: The HOTA T8 supports 1S-8S LiPo batteries. The built-in output port is XT60. If your battery uses an XT150 plug, you will need to prepare an XT60 to XT150 adapter cable separately.
- Outdoor Charging: If charging outdoors and needing to finish quickly, you can stop charging when the screen turns green (cell voltage difference < 20mV). For better balance, wait until the screen turns blue (cell voltage difference < 10mV) or slightly longer for more accurate results.
10. Product Qualification Declaration
The T8 Smart Charger conforms to relevant commands in B: 2017, PART15 CLASSB; FCC.
| Testing Standard | Result |
|---|---|
| EN 60950-1:2006+A11:2009+A1:2010+A12: 2011+A2:2013 | Yes |
| EN 62311:2008 | Yes |
| ETSI EN 301 489-1 V2.2.0(2017-03) | Yes |
| ETSI EN 301 489-3 V2.1.1(2017-03) | Yes |
| ETSI EN 303 417 V1.1.1(2017-09) | Yes |