Introduction
Thank you for choosing the BAOFENG BF-T18 Mini Long Range Walkie Talkie. This FM two-way radio transceiver is designed for use in the 446 private mobile radio service (PMR446) and FRS 462MHz bands. It comes pre-programmed with 16 PMR446 frequencies and FRS channels, offering a maximum transmission power of 500 mW and a bandwidth of 12.5 kHz. The BF-T18 features a fixed antenna, a maximum transmission time limit of 180 seconds, and operates without the need for registration or fees in many regions. However, please note that restrictions of use may apply in some non-EU countries.
The BF-T18 is an ideal and effective communication solution for professionals in various environments (e.g., construction sites, buildings, trade fairs, hotels) and for leisure users who wish to stay connected with friends and family during outdoor activities like camping or hunting.
ATTENTION: Before using this product, please read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control to ensure compliance with applicable standards and regulations.
Package Contents
The package includes the following items:
- 2 x BF-T18 Transceivers
- 2 x 1500mAh Li-ion Rechargeable Battery Packs
- 2 x Belt Clips
- 2 x Desktop Chargers
- 1 x Type-C USB Charger Cable

Product Overview and Controls
Familiarize yourself with the main controls and parts of your BF-T18 radio:

- Antenna: For transmitting and receiving signals.
- LCD Display: Shows channel, battery status, and other indicators.
- UP Button (▲): Press to increase volume. In menu mode, use to change settings.
- MENU Button (☰/MENU): Press to enter the radio's menu. Press and hold for approximately 3 seconds to activate the keypad lock.
- CALL Button (☎/CALL): Press to send a call to the selected channel. Press and hold to turn the radio on/off.
- DOWN Button (▼): Press to reduce volume. In menu mode, use to change settings.
- Speaker and Built-in Microphone: For audio output and input.
- LED Flashlight: Provides illumination.
- Belt Clip: For attaching the radio to your belt.
- MONI Button: Press and hold to activate the Monitor function for weak signal monitoring.
- SPK | MIC (2-pin Kenwood headset jack): Located under a protective cover, used to connect external audio devices like microphones or headphones.
- SCAN Button (☰/SCAN): Press once to activate channel scanning.
- USB Port: Type-C port for recharging the radio.
- PTT Button (Push-To-Talk): Press and hold to transmit your voice.
- LAMP/Emergency Button: Short press to turn the LED flashlight on/off. Press and hold to turn emergency alerts on/off.
LCD Display Indicators

- Scan Indicator: Appears when channel scanning is active.
- VOX Function Active: Indicates that hands-free operation is enabled.
- Dual Channel Monitor: Shows when the radio is monitoring two channels.
- CTCSS/DCS Squelch Type: Displays the selected sub-audio tone type.
- Channel (1-16): Current operating channel number.
- Battery Indicator: Shows the current battery level.
- Emergency Alert Function Activated: Indicates that the emergency alert is active.
- Transmit Status (TX): Appears when the radio is transmitting.
- Receive Status (RX): Appears when the radio is receiving a signal.
- Keypad Lock: Indicates that the keypad is locked.
- Transmit Power Indicator: Shows low power transmission (PMR mode only).
- CTCSS Tone or DCS Code: Displays the set CTCSS tone (1-50) or DCS code (1-105).
Setup
Battery Installation and Removal
The BF-T18 uses a 1500mAh Li-ion rechargeable battery pack (LB-T22).
To Install the Battery Pack:
- Remove the belt clip as described in the "Belt Clip Installation and Removal" section.
- Insert the battery pack into the appropriate compartment on the back of the radio.
- Close the battery compartment with the cover and re-attach the belt clip.
To Remove the Battery Pack:
- Remove the belt clip.
- Open the battery compartment cover.
- Remove the battery pack from the device.
- Close the battery compartment with the cover and re-attach the belt clip.

Belt Clip Installation and Removal
The belt clip allows you to easily attach the radio to your belt. It must be removed to install or replace the battery.
To Remove the Belt Clip:
Follow the illustration to detach the belt clip from the radio.
To Install the Belt Clip:
Fasten the clip into the slot on the unit in the radio's rear rail until it snaps into place.

Charging the Li-Ion Battery Pack
The BF-T18 features a convenient Type-C USB charging port.
- Place your transceiver in the desktop charger cradle or connect the Type-C USB cable directly to the radio's USB port and a suitable power source (e.g., wall adapter, power bank, car charger).
- The charging process is managed by a radio processor.
- Charging status is indicated by the LED on the desktop charger and by a flashing battery icon on the radio display.
- When charging is complete, the LED on the desktop charger will turn off, and the battery icon on the radio screen will show full bars.
Note: A full charge for the Li-Ion battery typically takes about 5 hours. It is recommended to disconnect the charger or remove the radio from the cradle once fully charged.

Operating Instructions
Power On/Off and Volume Adjustment
- To Turn On: Press and hold the ☎/CALL button until the radio powers on.
- To Adjust Volume: Press the ▲ (UP) or ▼ (DOWN) buttons.
- To Turn Off: Press and hold the ☎/CALL button until a switch-off tone is heard.
Talking on Your Radio (PTT)
- Ensure no one else is currently transmitting on the selected channel.
- Press and hold the PTT button. The TX icon will appear on the display.
- Pause slightly after pressing PTT, then speak clearly into the microphone (approx. 2-3 inches away).
- Release the PTT button when you finish speaking. The TX icon will disappear, and the radio will be ready to receive.
Monitor Mode
This feature allows you to listen for weak signals on the current channel.
- To Activate: Press the MONI button. The receiver circuit will open, allowing you to hear noise and weak signals. The RX icon will blink.
- To Deactivate: Press the MONI button again to return to normal mode. The RX icon will stop blinking.
Channel Scanning
The radio can automatically search for signals across PMR/FRS channels.
- To Start: Briefly press the ☰/SCAN button. The radio will scan channels in rapid sequence.
- To Transmit during Scan: If a signal is detected, scanning pauses. You can transmit by pressing PTT.
- To Change Scan Direction: Use the ▲ (UP) or ▼ (DOWN) buttons.
- To Stop: Press the ☰/SCAN button again. The transceiver will return to the channel from which scanning started.
Scanning Sub-Codes (CTCSS/DCS)
This function allows you to scan for CTCSS/DCS codes on a channel.
- To Enter: Press and hold the ☰/SCAN button. A flashing "CTC/DCS" will appear on the left status display.
- To Save: Press the PTT button to save the scanned tone into memory.
- To Exit: Press and hold the ☰/SCAN button again.
VOX Function (Hands-Free Operation)
VOX allows for hands-free communication.
- Press the ☰/MENU button 4 times until 'VOX' appears on the display.
- Use the ▲ (UP) or ▼ (DOWN) buttons to select the desired sensitivity level (1=high, 2=medium, 3=low).
- Press the PTT button to exit the menu or ☰/MENU to continue setup.
- To Disable: Follow the same steps and select 'oF' (Off).
Call Tones
The radio offers 10 selectable call tones to alert other users in your group.
- Press the ☰/MENU button 5 times until "CA" appears on the display.
- Use the ▲ (UP) or ▼ (DOWN) buttons to listen to the 10 pre-programmed melodies.
- Press the PTT button to exit the menu or ☰/MENU to continue setup.
- To Transmit a Call Tone: Set your radio to the same channel and Sub-Code as the receiving radios, then press the ☎/CALL button.
- To Disable: Follow the same steps and select 'oF' (Off).
Emergency Alert
This feature can be used to signal for help to members in your group.
- To Activate: Press the ☰/MENU button 6 times until the display shows the emergency alert icon.
- Use the ▲ (UP) or ▼ (DOWN) buttons to select the desired setting:
- Local Alarm: The radio itself emits an alarm sound.
- Send Alarm Tone: An alarm tone is sent on the current channel to alert group members.
- Press the PTT button to exit the menu or ☰/MENU to continue setup.
- To Exit: Press the LAMP/Emergency button.
WARNING: The Emergency Alert feature should only be used in a true emergency. Baofeng assumes no responsibility if the receiving group does not respond to the distress signal.
Keypad Lock
To prevent accidental changes to radio settings:
- To Activate: Press and hold the ☰/MENU button for 3 seconds. The keypad lock icon will appear on the display. The PTT, CALL, and MONI keys remain active.
- To Deactivate: Press and hold the ☰/MENU button for 3 seconds again.
Roger Beep (End Transmission Tone)
This tone signals to the other party that your transmission has ended and they can begin speaking. It is enabled by default.
- To Deactivate: Press the ☰/MENU button 8 times until "rbon" is displayed. Use the ▲ (UP) or ▼ (DOWN) buttons to select "roof" (Off). Press PTT or ☰/MENU to exit/continue.
Dual Watch Mode
This function allows the radio to monitor two channels for activity simultaneously.
- Press the ☰/MENU button 9 times until "of du" is displayed.
- Use the ▲ (UP) or ▼ (DOWN) buttons to select the second channel you wish to monitor, then press ☰/MENU.
- Use the ▲ (UP) or ▼ (DOWN) buttons to select the CTCSS/DCS code for the second channel, then press ☰/MENU.
- The radio will begin Dual Watch, alternating between the home channel and the selected second channel.
- To Turn Off: Press the ☰/SCAN button.
Note: Dual Watch will not function if you set the same channel and sub-code for both monitored channels.
Flashlight Operation
The radio is equipped with a strong LED flashlight.
- To Turn On/Off (Continuous): Short press the LAMP/Emergency button.
- To Activate Strobe Light (Emergency Signal): Press the LAMP/Emergency button once for continuous light, then press it again for strobe.
- To Turn Off Strobe: Press the LAMP/Emergency button a third time.

NOAA Weather Radio Service
The BF-T18 supports NOAA Weather Radio Service, allowing you to listen to All Hazards Weather Channels and Alerts to withstand extreme weather conditions.

Video 1: Baofeng BF-T18 Walkie Talkie overview, showcasing different color options, Type-C charging, battery installation, and various functions like dual PTT and flashlight.
Technical Specifications
| Category | Specification |
|---|---|
| General Part | |
| Frequency Range | 446.00625-446.19375 MHz (PMR446), 462-467MHz (FRS) |
| Channels | FRS 22 / PMR 16 |
| Working Temperature | -10°C to +50°C |
| Operation Voltage | DC 3.7 V ±10% |
| Operation Mode | Simplex |
| Dimensions (without Antenna) | 168mm x 57mm x 34.5mm |
| Weight (Battery pack included) | 150g |
| Antenna Impedance | 50ohm |
| Category | B |
| Transmitter Part | |
| Frequency Stability | ±2.5ppm |
| RF Output Power | ≤500mW ERP |
| Max Frequency Deviation | ≤2.5KHz |
| Audio Distortion | <3% |
| Adjacent Channel Power | < 60dB |
| Receiver Part | |
| Receive Sensitivity | < 0.2µV @20dB SINAD |
| Audio Distortion | <3% |
| Audio Response | 300 Hz ~ 3 KHz |


Maintenance
To ensure your BF-T18 provides years of reliable service, please follow these recommendations:
- Do not attempt to open the unit. Non-expert handling can damage the device and void the warranty.
- When using a regulated power supply, ensure the output voltage is 5V to prevent damage.
- Avoid exposing the radio to high temperatures, as this can shorten the life of electronic components and deform or melt plastic parts.
- Do not store the radio in dusty or dirty areas.
- Keep the radio dry. Rainwater or dampness can corrode electronic circuits.
- If the radio emits a peculiar smell or smoke, immediately turn off its power, disconnect the charger, and remove the battery.
- Do not transmit without an antenna.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Radio does not turn on | Low or depleted battery; Incorrect battery installation. | Charge the battery; Reinstall the battery correctly. |
| Cannot transmit or receive | Incorrect channel/sub-code; Out of range; Obstructions; Low battery. | Verify channel and CTCSS/DCS settings; Move closer to other radios; Reduce obstructions; Charge battery. |
| Poor audio quality / Static | Weak signal; Out of range; Interference; Antenna issue. | Move closer; Check antenna connection; Use Monitor mode to check for weak signals. |
| VOX function not working as expected | Incorrect sensitivity setting; VOX disabled. | Adjust VOX sensitivity (levels 1-3); Ensure VOX is enabled in the menu (not 'oF'). |
| Keypad is unresponsive | Keypad lock is active. | Press and hold the ☰/MENU button for 3 seconds to unlock. |
User Tips
- VOX Activation: Some users have reported difficulty activating the VOX function. Ensure you follow the instructions precisely: press the MENU button 4 times until 'VOX' appears, then adjust sensitivity. If issues persist, try resetting the radio or consult the full PDF manual.
- Range Optimization: For best range, especially in open areas, ensure minimal obstructions between radios. The stated 10km range is typically achieved in clear line-of-sight conditions, such as in mountains.
- Battery Life: The 1500mAh Li-ion battery provides up to 18 hours of use under typical conditions. For extended use, consider carrying a power bank for Type-C charging.
- Regional Frequencies: Remember to select the correct frequency band (PMR 446MHz for Europe, FRS 462MHz for North/South America) based on your location to ensure legal and effective communication.
Warranty and Support
Baofeng and Pofung declare that the radio equipment type listed in the Technical Specifications complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available online.
For support or warranty inquiries, please contact your local Baofeng helpdesk or the dealer from whom you purchased this radio. You may also send an email to wangjianhui@baofengradio.com.
Further information can be found on the official website: http://www.baofengradio.com.
FCC ID: 2AJGM-GT18