LHY Audio EFI

Contents

LHY Audio EFI Optoelectronic Isolator Network Filter

Model: EFI

1. Introduction

The LHY Audio EFI (Ethernet Filter with Optical Isolation) is a dedicated audio network optical isolation purifier designed to significantly improve the home audio network environment. It protects streaming media transmission from noise interference, thereby enhancing the quality of music and video streams.

High-frequency crosstalk noise from home networks can negatively affect the sound performance of streaming devices. The EFI addresses this by providing effective optoelectronic isolation, which has an immediate and noticeable effect on the sound quality of playback devices.

Traditionally, achieving high-quality optical isolation required a complex setup involving multiple optoelectronic converters, linear power supplies, optoelectronic modules, and fiber optic cables. The EFI integrates these components into a single, compact device, simplifying installation and reducing clutter.

Silver and black LHY Audio EFI units
Figure 1: LHY Audio EFI Optoelectronic Isolator Network Filter (Silver and Black models)
Comparison of traditional optical isolation setup vs. EFI simplified solution
Figure 2: Simplified system integration with EFI compared to traditional multi-device optical isolation setups.

2. Product Overview

The EFI unit features two RJ45 network ports, a power input, and a power switch. It is available in both silver and black finishes.

Front and rear view of the silver LHY Audio EFI unit
Figure 3: Front and rear view of the silver EFI unit, showing ports and controls.
Front and rear view of the black LHY Audio EFI unit
Figure 4: Front and rear view of the black EFI unit, showing ports and controls.

Port Descriptions:

  • LAN-IN: The front-end network input interface (RJ45 port). This port is recommended for connecting network signals from your optical modem, router, or network switch.
  • ISOLATED: The optoelectronic isolation network output (RJ45 port). This port is recommended for connecting to audio devices that require high-quality network signals, such as digital broadcasters, streamers, or switches.
Close-up of the EFI rear panel highlighting LAN-IN and ISOLATED ports
Figure 5: Detailed view of the EFI rear panel, indicating LAN-IN and ISOLATED ports.

3. Setup Instructions

  1. Power Connection: Connect the provided IEC power cord to the EFI unit and then to a suitable power outlet (110V~240VAC).
  2. Input Network Connection: Connect an Ethernet cable (e.g., the included Category 6 cable) from your router, modem, or network switch to the LAN-IN port on the EFI.
  3. Output Network Connection: Connect another Ethernet cable from the ISOLATED port on the EFI to your audio streaming device (e.g., digital broadcaster, network streamer, Roon core, or audio-grade network switch).
  4. Power On: Flip the power switch on the rear panel of the EFI to the 'ON' position. The indicator light on the front panel should illuminate.
Connection diagram: Router to EFI to RPI/DAC
Figure 6: Typical connection diagram showing the EFI integrated into an audio network system.
EFI connected to a laptop and another audio device
Figure 7: Example setup with EFI connected to a laptop and an audio device.

4. Operating Instructions

The EFI operates by converting incoming electrical network signals from the LAN-IN interface into optical signals using high-performance optoelectronic modules. These optical signals are then transmitted internally and converted back into electrical signals by another set of high-performance optoelectronic modules. The purified and isolated network electrical signals are then output through the ISOLATED RJ-45 network interface.

This process achieves electrical signal isolation between the input and output. Coupled with its built-in two sets of high-performance uV level linear power supplies, the EFI effectively eliminates interference noise and stray currents originating from routers or switches. Multi-stage filtering further removes EMI (electromagnetic interference) and RFI (radio frequency interference) noise from incoming devices.

The result is a cleaner network signal, leading to improved overall music quality, a cleaner audio background, more prominent details, and a more natural and vivid sound experience for both music and video streaming.

Diagram illustrating network noise purification via optical isolation
Figure 8: Illustration of how the EFI's optical isolation purifies network signals from noise.
Flowchart of EFI signal conversion and output to various network devices
Figure 9: EFI's signal path: electrical to optical and back, for purified output to network devices.
Audio signal chain with EFI, decoder, amplifier, and speakers
Figure 10: The EFI integrated into an audio playback chain for enhanced sound quality.

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the EFI unit. Avoid using liquid cleaners or abrasive materials.
  • Ventilation: Ensure the unit is placed in a well-ventilated area to prevent overheating. Do not block any ventilation openings.
  • Cable Management: Keep network and power cables tidy and free from kinks or excessive bending to ensure optimal performance and longevity.
  • Fuse Replacement: The unit uses a T1.0AL fuse (100V-240VAC). If the unit fails to power on, check the fuse located within the IEC power inlet. Replace it with a fuse of the same type and rating if necessary. Always disconnect power before checking or replacing the fuse.

6. Troubleshooting

  • No Power:
    • Ensure the power cord is securely connected to both the EFI and the power outlet.
    • Check if the power switch on the rear panel is in the 'ON' position.
    • Verify the power outlet is functional.
    • Inspect and replace the T1.0AL fuse if it is blown (refer to Maintenance section).
  • No Network Signal / Poor Audio Quality:
    • Ensure all Ethernet cables are securely connected to the LAN-IN and ISOLATED ports on the EFI, and to your router/modem and audio device.
    • Verify that your router/modem is functioning correctly and providing an active network signal.
    • Check the status indicator lights on the EFI (if present) and your connected network devices for any error indications.
    • Try using different Ethernet cables to rule out cable issues.
    • Temporarily bypass the EFI to see if the issue persists, which can help determine if the problem lies with the EFI or other components in your network/audio chain.

7. Specifications

Feature Specification
Network Ports Standard RJ45 (LAN-IN), Optoelectronic Isolation RJ45 (ISOLATED)
Network Protocol IEEE 802.3 ×
Supported Speeds 10/100/1000 Mbps
Input Voltage 110V~240VAC
Power Consumption 6W~7W
Dimensions (W × D × H) 155 × 175 × 50mm
Weight 1.2 Kg
Internal Components Large capacity filter capacitor array, Two sets of high-current common mode noise reduction inductors, EMI AC filter, Two sets of high-performance power modules, Two independent LT3042+PNP uV-level linear power supplies for optoelectronic conversion circuits, High-precision optoelectronic conversion modules, Gigabit isolation network socket.
Accessories Included Category 6 1.5-meter Ethernet cable × 1, IEC power cord × 1
Internal view of the EFI showing components like capacitors, inductors, and power modules
Figure 11: Internal view of the EFI, highlighting key components for noise reduction and power delivery.
Detailed view of internal optoelectronic conversion modules and linear power supplies
Figure 12: Close-up of the EFI's high-precision optoelectronic conversion modules and dedicated linear power supplies.

8. User Tips

  • Cable Quality: While a Category 6 Ethernet cable is included, using high-quality, shielded Ethernet cables for both input and output connections can further minimize potential interference and maximize the benefits of the EFI.
  • Dedicated Power: For optimal performance, consider connecting the EFI to a clean power source, such as a dedicated audio power conditioner, if available.
  • Placement: Position the EFI away from other high-noise electronic devices (e.g., power transformers, Wi-Fi routers) to prevent any potential electromagnetic interference, although the unit is designed for isolation.

9. Warranty and Support

For any technical assistance, warranty claims, or support inquiries, please contact your authorized LHY Audio dealer or the seller directly. Ensure you have your purchase details and product model information readily available.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.