Flipsky FSESC6.7 Plus

Contents

Flipsky 4-12S 400A Dual BLDC Motor FSESC6.7 Plus Electric Skateboard Speed Controller User Manual

Model: FSESC6.7 Plus

1. Introduction

Thank you for choosing the Flipsky FSESC6.7 Plus Dual BLDC Motor Speed Controller. This high-performance Electronic Speed Controller (ESC) is designed for electric skateboards and similar applications, offering robust power delivery and precise motor control. Based on the VESC6 platform, it supports 4-12S LiPo battery configurations and provides up to 400A instantaneous current per single motor. This manual will guide you through the installation, operation, and maintenance of your FSESC6.7 Plus to ensure optimal performance and longevity.

2. Safety Instructions

  • Voltage Limits: Ensure your battery voltage does not exceed 60V. This ESC is safe for 3S to 12S LiPo configurations. Exceeding the maximum voltage can cause permanent damage.
  • Current Handling: The ESC can handle continuous 100A per single motor (200A total) and instantaneous current up to 400A per single motor (800A total). These values are dependent on proper mounting and ambient temperature. Ensure adequate cooling.
  • Firmware: It is strongly recommended to keep the firmware version 5.2 as shipped from the factory. Upgrading to newer firmware versions may potentially damage the ESC. Proceed with caution if attempting firmware updates.
  • Physical Protection: Do not remove the shrink wrap or aluminum case protecting the PCB. This covering shields the electronic components from impurities, moisture, and metal debris, which could lead to short circuits or irreversible damage.
  • Proper Connections: Always double-check all wiring connections before powering on the device. Incorrect wiring can cause severe damage to the ESC, motors, and battery.
  • Environment: Operate the ESC in a clean, dry environment, away from conductive materials and excessive heat.

3. Package Contents

Upon opening your Flipsky FSESC6.7 Plus package, please verify that all the following items are included:

  • Flipsky FSESC6.7 Plus Dual BLDC Motor Speed Controller (with Heat Sink or Aluminum Case, depending on your selection)
  • Power Switch Button
  • Various connection cables (e.g., sensor cables, PPM cable)
  • USB Cable for configuration
Contents of the Flipsky FSESC6.7 Plus package, including the ESC, power button, various cables, and a USB cable.
Figure 3.1: Contents of the Flipsky FSESC6.7 Plus package.

4. Specifications

FeatureDetail
Hardware VersionV 6.7
Firmware VersionLatest (Factory recommends keeping 5.2)
Voltage Range8V - 60V (3S to 12S LiPo compatible)
Continuous Current100A (single), 200A (total)
Instantaneous Current400A (single), 800A (total)
5V BEC Output1.5A
3.3V BEC Output1A
Control ModesDC, BLDC, FOC (sinusoidal)
Supported SensorsABI, HALL, AS5047, AS5048A
ERPM150000
Dimensions (with Heat Sink)78mm x 78mm x 27.3mm
Dimensions (with Aluminum Case)83mm x 83mm x 18.3mm
Power Wire Size8 AWG
Motor Wire Size12 AWG
Recommended Bullet Connectors4MM Bullet Connector
Battery Voltage Tolerance+/-0.6V
ProgrammableYes
Regenerative CapacityYes
Control Interface PortsUSB, CAN, UART, SPI, IIC (for IMU)
Input Signals SupportPPM, ADC, NRF, UART
Power Switch ButtonRed
Dimensions of the Flipsky FSESC6.7 Plus with Heat Sink: 78mm x 78mm x 27.3mm.
Figure 4.1: Dimensions of the FSESC6.7 Plus with Heat Sink.
Dimensions of the Flipsky FSESC6.7 Plus with Aluminum Case: 83mm x 83mm x 18.3mm.
Figure 4.2: Dimensions of the FSESC6.7 Plus with Aluminum Case.

5. Setup and Installation

5.1 Component Overview

The FSESC6.7 Plus features a compact design with clearly labeled ports for easy integration into your electric skateboard system. It includes a power button for convenient on/off control and a CAN bus connector for multi-ESC setups.

Top view of the Flipsky FSESC6.7 Plus with Heat Sink, showing capacitor bank and connection ports.
Figure 5.1: Top view of the FSESC6.7 Plus with Heat Sink.
Top view of the Flipsky FSESC6.7 Plus with Aluminum Case, highlighting the integrated power button and connection points.
Figure 5.2: Top view of the FSESC6.7 Plus with Aluminum Case.

5.2 Wiring Diagram and Connections

Refer to the diagrams below for detailed port identification and wiring instructions. Ensure all connections are secure and correctly oriented before applying power.

Detailed diagram of the Flipsky FSESC6.7 Plus connection ports and their labels.
Figure 5.3: FSESC6.7 Plus Port Diagram.

Port Identification:

  • 1. BUTTON: Connect the provided power switch button here.
  • 2. SENSE1: Sensor port for Motor 1 (H1, H2, H3, TMP, 5V, GND).
  • 3. USB1: USB port for configuration and firmware updates.
  • 4. CAN: CAN bus connector for linking multiple ESCs (e.g., for 4WD setups).
  • 5. PPM+UART: Port for PPM receiver and UART communication.
  • 6. USB2: Secondary USB port.
  • 7. SENSE2: Sensor port for Motor 2 (H1, H2, H3, TMP, 5V, GND).
  • 8. COMM1: Communication port 1 (ADC3, ADC2, TX, RX, ADC1, 3.3V, 5V).
  • 9. COMM2: Communication port 2 (ADC3, ADC2, TX, RX, ADC1, 3.3V, 5V).
Wiring diagram illustrating the connection of the Flipsky FSESC6.7 Plus to a battery, two motors, and a PPM receiver.
Figure 5.4: Typical Wiring for Battery, Motors, and PPM Receiver.

Installation Steps:

  1. Mounting: Securely mount the FSESC6.7 Plus to your electric skateboard chassis. Ensure good airflow around the unit, especially if using the heat sink version, to prevent overheating.
  2. Battery Connection: Connect your 3S-12S LiPo battery to the main power cables (8 AWG) of the ESC. Pay close attention to polarity (red for positive, black for negative).
  3. Motor Connection: Connect your BLDC motors to the motor phase wires (12 AWG) of the ESC. For sensored motors, connect the sensor cables to the SENSE1 and SENSE2 ports.
  4. Receiver Connection: Connect your PPM receiver to the PPM+UART port. Ensure the correct pinout for GND, 5V, and Signal (SIN).
  5. Power Button: Connect the provided power switch button to the BUTTON port.
  6. Optional Connections: If using multiple ESCs for a 4WD setup, connect them via the CAN bus port. For other external electronics or accessories, use the appropriate communication ports (COMM1, COMM2) or BEC outputs (5V 1.5A, 3.3V 1A).
  7. Initial Configuration: Before first use, connect the ESC to a computer via the USB port and use the VESC Tool software for motor detection and parameter configuration. This is crucial for safe and efficient operation.

6. Operating Instructions

  1. Power On: Press the connected power switch button to turn on the ESC. The LED indicators on the board will illuminate.
  2. Motor Control: Use your remote control (connected via PPM or other supported input signals) to control the speed and direction of the motors.
  3. Modes: The FSESC6.7 Plus supports various control modes including DC, BLDC (Brushless DC), and FOC (Field-Oriented Control). FOC mode generally provides smoother and quieter operation. Select your preferred mode during the VESC Tool configuration.
  4. Power Off: Press the power switch button again to turn off the ESC.

7. Maintenance

  • Keep Shrink Wrap/Case Intact: As a critical safety and protection measure, never remove the factory-applied shrink wrap or aluminum case. It protects the sensitive PCB components from environmental factors like dust, moisture, and conductive debris, which can cause short circuits and damage.
  • Regular Inspection: Periodically inspect all wiring connections for signs of wear, corrosion, or looseness. Ensure bullet connectors are firmly seated.
  • Cleaning: Keep the ESC and its surroundings clean. Use a soft, dry brush or compressed air to remove dust and debris. Avoid using liquids or solvents.
  • Temperature Monitoring: During operation, especially under heavy loads, monitor the temperature of the ESC. Excessive heat can degrade performance and shorten lifespan. Ensure adequate ventilation.

8. Troubleshooting

If you encounter issues with your FSESC6.7 Plus, consider the following:

  • No Power: Check battery connections, ensure the power switch is functioning, and verify battery charge.
  • Motor Not Spinning/Irregular Operation: Verify motor phase wire connections and sensor cable connections (if applicable). Re-run motor detection in VESC Tool. Check for any error codes in the VESC Tool terminal.
  • Remote Control Issues: Ensure your receiver is correctly connected to the PPM+UART port and properly bound to your remote. Check remote battery levels.
  • Overheating: Reduce load, improve ventilation, or consider a larger heat sink/cooling solution. Check motor current limits in VESC Tool.
  • ESC Damage after Firmware Update: If issues arose after a firmware update, it might be related to the firmware version. As advised, it's best to stick to the factory firmware (v5.2) unless you are experienced and understand the risks.

For persistent issues, consult online VESC communities or contact Flipsky support.

9. User Tips

  • Configuration Software: Utilize the VESC Tool software for comprehensive configuration and monitoring. It allows fine-tuning of motor parameters, current limits, and input settings.
  • Cable Management: Organize and secure all cables to prevent them from snagging, rubbing, or interfering with moving parts. This reduces the risk of damage and improves reliability.
  • Water Resistance: While the aluminum case offers some protection, the ESC is not fully waterproof. Avoid exposing it to water or excessive moisture. Consider additional waterproofing measures for outdoor use.
  • Start with Low Settings: When first configuring, start with conservative motor and battery current limits in VESC Tool. Gradually increase them as you become familiar with the system's performance.

Note: No specific user reviews or Q&A data were provided to extract additional tips. The above are general best practices for ESCs.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or Flipsky directly through their official channels. Keep your proof of purchase for any warranty claims. Ensure you have your product model (FSESC6.7 Plus) and any relevant serial numbers ready when contacting support.

© 2024 Flipsky. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.