HGLRC M100-5883 M10 GPS

Contents

HGLRC M100-5883 M10 GPS Module

User Instruction Manual

1. Introduction

The HGLRC M100-5883 M10 GPS Module is a high-precision positioning system designed for RC airplanes, FPV drones, and other unmanned aerial vehicles. Featuring a 10th generation M10 chip, ceramic antenna, and an integrated QMC5883 compass, this compact module provides fast, stable, and accurate positioning data. On-board LED indicators offer real-time status updates for power and GPS lock.

Video: HGLRC M100-5883 M10 GPS Module product showcase.

2. Product Overview and Features

  • Advanced Chipset: Utilizes the 10th generation M10 chip for enhanced performance.
  • Integrated Compass: Features a QMC5883 compass for accurate heading information.
  • High-Performance Antenna: Equipped with a ceramic antenna for reliable satellite signal reception.
  • Multi-Constellation Support: Supports GPS/QZSS L1C/A, SBAS, GLONASS L1OF, BDS B1I, and Galileo E1B/C.
  • Compact Design: Small and exquisite with dimensions of 21x21x8.02mm and a weight of only 7.73g.
  • On-board LED Indicators: Power (blue) and PPS positioning (red) indicators for easy status monitoring.
  • Fast Positioning: Designed for extremely fast satellite acquisition and stable signal.
HGLRC M100-5883 M10 GPS Module highlighting fast positioning, stable signal, small size, and accurate positioning.

Image: Key features of the HGLRC M100-5883 M10 GPS Module.

3. Package Contents

Please check the package contents upon receipt:

  • 1x HGLRC M100-5883 M10 GPS Module
  • 1x Connection Cable
  • 1x Double-sided Adhesive Pad
  • 1x Sticker Sheet
  • 1x Quality Certificate
Contents of the HGLRC M100-5883 M10 GPS Module package including the module, cable, adhesive, stickers, and certificate.

Image: HGLRC M100-5883 M10 GPS Module and included accessories.

4. Setup

4.1. Wiring Diagram

Connect the GPS module to your flight controller according to the diagram below. Ensure correct pin matching to avoid damage.

Wiring diagram showing connections from HGLRC M100-5883 GPS module to a flight controller. SCL to SCL, SDA to SDA, RX to TX, TX to RX, 5V to 5V, GND to GND.

Image: Wiring diagram for HGLRC M100-5883 M10 GPS Module.

  • GPS SCL ↔ Flight Controller SCL
  • GPS SDA ↔ Flight Controller SDA
  • GPS RX ↔ Flight Controller TX
  • GPS TX ↔ Flight Controller RX
  • GPS 5V ↔ Flight Controller 5V
  • GPS GND ↔ Flight Controller GND

4.2. Betaflight Setup

  1. Open the Ports tab in Betaflight Configurator.
  2. Identify the UART port to which your GPS module is connected (e.g., UART3).
  3. For that UART, set Sensor Input to GPS.
  4. Set the Baud Rate for that UART to 115200.
  5. Navigate to the Configuration tab.
  6. Under the GPS section, enable GPS and select UBLOX as the protocol.
  7. Save and Reboot.

After powering on the aircraft, the GPS module's indicator light should be on, and the GPS logo should appear on the top of the Betaflight OSD (if configured).

Betaflight setup instructions showing Ports tab configuration for GPS on UART3 with 115200 baud rate and Configuration tab with UBLOX protocol enabled.

Image: Betaflight setup steps.

4.3. INAV Setup

  1. Open the Ports tab in INAV Configurator.
  2. Identify the UART port to which your GPS module is connected (e.g., UART3).
  3. For that UART, set Sensor Input to GPS.
  4. Set the Baud Rate for that UART to 115200.
  5. Navigate to the Configuration tab.
  6. Under the GPS section, enable GPS and select UBLOX as the protocol.
  7. In the Sensors & buses section, for Compass Selection, choose QMC 5883.
  8. Save and Reboot.

After powering on the aircraft, the GPS module's indicator light should be on, and the GPS and compass icons should appear on the top of the INAV OSD (if configured).

INAV setup instructions showing Ports tab configuration for GPS on UART3 with 115200 baud rate, Configuration tab with UBLOX protocol enabled, and Sensors & buses tab with QMC 5883 selected for compass.

Image: INAV setup steps.

4.4. Compass Calibration

After enabling the compass in your flight controller firmware, it is crucial to perform a compass calibration before the first flight and whenever the module's orientation or location on the craft changes significantly. Refer to your flight controller's documentation (Betaflight/INAV) for detailed calibration procedures.

5. Operating

5.1. LED Indicators

The module features two on-board LED indicators to show its operational status:

Status PPS (Red Light) Power (Blue Light)
Normal Start (Power On) Normal Bright Normal Bright
Real Position Accuracy (GPS Lock) Flickering Normal Bright
Function description of HGLRC M100-5883 GPS module showing LED indicator table for PPS (red) and Power (blue) lights.

Image: LED indicator function description.

5.2. Installation and Orientation

For optimal performance, the GPS module must be installed with the ceramic antenna facing upwards, unobstructed by other components. Position it as far away as possible from motors, power lines, video transmitters, and other sources of electromagnetic interference.

6. Maintenance

  • Handling: Handle the module with care to avoid damaging the ceramic antenna or sensitive electronic components.
  • Cleaning: If necessary, gently clean the module with a soft, dry cloth. Avoid using liquids or solvents.
  • Storage: Store the module in a dry, anti-static environment when not in use.
  • Firmware: Ensure your flight controller firmware is up-to-date (BF4.3.0 or above) for compatibility with the 10th generation GPS chip.

7. Troubleshooting

  • No GPS Lock:
    • Ensure the antenna is facing up and has a clear view of the sky.
    • Check wiring connections (RX/TX, 5V/GND).
    • Verify Betaflight/INAV port and configuration settings (GPS enabled, UBLOX protocol, 115200 baud rate).
    • Ensure sufficient power supply (3.3-5V).
    • Check for interference from other electronics (motors, VTX).
  • Compass Not Working/Inaccurate:
    • Perform compass calibration.
    • Check SDA/SCL wiring.
    • Ensure QMC5883 is selected in INAV/Betaflight (if applicable).
    • Relocate the GPS module further from magnetic interference sources.
  • Module Not Recognized:
    • Verify power supply and all wiring.
    • Ensure flight controller firmware is BF4.3.0 or above.
Important attention notes for HGLRC M100-5883 GPS module: calibrate compass, supply correct voltage, solder carefully, use BF4.3.0+ firmware, install antenna facing up away from interference.

Image: Important attention notes.

8. Specifications

Parameter Value
Chip M10 (10th generation chip)
Antenna Ceramic antenna
Frequency GPS/QZSS L1C/A, SBAS EGNOS, GAGAN, MSAS and WAAS, GLONASS L1OF, BDS B1I, Galileo E1B/C
Receive Channel 72ch
Baud Rate 115200bps
Output Protocol UBLOX
Output Frequency 10Hz
Power Input 3.3-5V
Dimensions (LxWxH) 21x21x8.02mm
Weight 7.73g
Technical specifications for HGLRC M100-5883 GPS module including chip, antenna, frequency, channels, baud rate, output protocol, frequency, power, size, and weight.

Image: Detailed technical specifications.

9. User Tips

  • Wiring Caution: Some users have noted that the TX and RX wire colors in the provided cable might be reversed compared to standard conventions. Always double-check the pin labels on the module and your flight controller before connecting to avoid damage.
  • Fast Acquisition: This GPS module is known for its quick satellite acquisition, often locking onto 12 or more satellites within a minute under clear skies.
  • RC Wing Suitability: It performs very well as a GPS satellite receiver for RC wing models.

10. Warranty and Support

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty validation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.