1. Introduction
This manual provides essential information for the safe and effective use of the Flipsky 60V 120A Smart Antispark Switch V1.3. Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage to the device or connected components. This smart switch is designed to manage power flow and prevent damaging sparks during battery connection in high-power electric applications.
2. Specifications
| Feature | Detail |
|---|---|
| Hardware Version | V1.3 |
| Max Voltage | 13S (60V) |
| Continuous Current | 60A |
| Max Current | 120A |
| Mosfets | NTMFS5C612NL-D (10pcs) |
| LED Button Diameter | 12mm |
| LED Cable Length | 250mm |
| PCB Thickness | 4 layers * 3oz copper = 12oz copper |
| PCB Size | 40mm * 32mm * 17mm |
| Material | Metal |
| Recommended Use | Vehicles & Remote Control Toys |
| Recommended Age | 14+ years |
| Is Electric | No Battery |
| Battery/Power Supply Included | No |
| Charger/Adapter Included | No |
3. Key Features
- High Side Switching: Ensures safer operation when used with multiple Electronic Speed Controllers (ESCs) and other devices by switching the positive line.
- In-rush Current Limiting: An integrated RC delay network effectively restricts inrush current to safe levels, protecting components from sudden power surges. The dV/dt is approximately 100V/s, resulting in an inrush current of 600mA at 6,000 uF output capacitance.
- Smart Power On/Off: Intelligent power management for convenient and reliable system control.
- Roll-to-Start Functionality: Features a 12-second blanking timer after the device is turned off. During this period, if the system detects movement (e.g., rolling an electric skateboard), it can automatically power on without needing to press the button.
- Automatic Turn-Off: To conserve power, the switch will automatically power off after 20 minutes of inactivity. Activity is defined as the output voltage varying by at least 500mV within any three-second interval.
- Momentary Push Button Support: Provides intuitive control with a single button:
- Hold for 0.3 seconds to turn on.
- Hold for 1 second to turn off.
- Continuously holding the button will cycle the device on and then off.
4. Safety Warnings and Precautions
Failure to follow these warnings may result in damage to the device, connected components, or personal injury. Always prioritize safety when working with high-power electrical systems.
- Heat Shrink Integrity: Do not peel off the heat shrink. The heatsink and PCBA are secured by a heat-transfer silicon pad, not screws. Removing the heat shrink may compromise thermal management and structural integrity, leading to overheating and failure.
- Short Circuit Protection: This device does NOT have short circuit protection. DO NOT short circuit the output. A short circuit can cause severe damage to the switch, battery, and other components, and poses a fire hazard.
- Reverse Polarity: This device does NOT have reverse polarity protection. DO NOT plug in the power source backwards. Incorrect polarity will immediately damage the switch and potentially other connected electronics. Always double-check connections before applying power.
- Output Capacitance: It is recommended to keep the total output capacitance of your system (e.g., from ESCs) under 6,000 uF. Proper operation and inrush current limiting cannot be guaranteed at higher capacitances, which could lead to switch failure.
- Hot-Swapping: Avoid hot-swapping (connecting or disconnecting components while power is applied). Always ensure everything is off before connecting or removing components. This prevents arcing and potential damage.
- When disconnecting: Unplug from the battery first, wait for ESCs to fully discharge and turn off, then unplug the ESCs from the switch.
- When connecting: Plug in the ESCs to the switch first, then plug the switch into the battery.
- New Design Caution: This is a new design and a first production run. While thoroughly tested, exercise extreme caution, as you would with any electric vehicle component.
- MCU Reprogramming: Do not attempt to reprogram the Microcontroller Unit (MCU) unless specifically advised by the manufacturer. Doing so will void any warranty and significantly increase the risk of switch failure.
5. Setup and Installation
The Flipsky Smart Antispark Switch V1.3 is designed to be integrated between your battery and Electronic Speed Controller(s) (ESCs). Follow the wiring diagram carefully to ensure correct and safe installation.
5.1. Wiring Connection
Refer to the diagrams below for correct wiring. Ensure all connections are secure, properly insulated, and observe correct polarity at all times.
- Battery Connection: Connect the positive (+) and negative (-) terminals of your battery to the 'IN+' and 'IN-' terminals on the Anti-Spark Switch, respectively. Use appropriate gauge wires for your current requirements.
- ESC Connection: Connect the 'OUT+' and 'OUT-' terminals of the Anti-Spark Switch to the corresponding positive (+) and negative (-) power input terminals of your VESC(s) or ESC(s).
- LED Button Connection: Connect the 12mm LED push button to the designated connector on the Anti-Spark Switch. Ensure the K+, L+, and -(K-L)- wires are correctly aligned as shown in Figure 2. Incorrect wiring of the button may prevent the switch from operating or damage the button.
- Secure Connections: Ensure all connections are soldered properly or secured with appropriate high-current connectors (e.g., XT60, XT90, AS150) to prevent loose connections, resistance, and potential arcing.
- Insulation: After making connections, ensure all exposed wires and terminals are properly insulated to prevent short circuits.
6. Operating Instructions
6.1. Powering On/Off
- To Turn On: Press and hold the momentary push button for approximately 0.3 seconds. The LED on the button should illuminate, indicating the switch is active and power is supplied to your ESCs.
- To Turn Off: Press and hold the momentary push button for approximately 1 second. The LED on the button should turn off, indicating the switch is inactive and power to your ESCs has been cut.
- Cycling On/Off: If you continuously hold the button for an extended period, it will cycle the device on and then off. Release the button after the desired state is achieved.
6.2. Roll-to-Start Function
The switch supports a "Roll-to-Start" feature. After the device has been turned off, there is a 12-second blanking timer. During this period, if the system detects movement (e.g., rolling an electric skateboard), it can automatically power on without needing to press the button. This provides a convenient way to quickly resume operation.
6.3. Automatic Turn-Off
To conserve battery power, the switch is equipped with an automatic turn-off feature. If no significant activity is detected, the device will power off after 20 minutes. Activity is defined as the output voltage varying by at least 500mV within any three-second interval. Ensure your system generates sufficient voltage variation during operation to prevent unintended shutdowns, especially during long idle periods.
7. Maintenance
The Flipsky Smart Antispark Switch V1.3 is designed for durability and requires minimal maintenance. However, regular checks can prolong its lifespan and ensure safe and reliable operation.
- Visual Inspection: Periodically inspect the switch, its wiring, and all connections for any signs of wear, damage, fraying, or loose wiring. Address any issues promptly.
- Cleanliness: Keep the device free from dust, dirt, moisture, and corrosive substances. Use a dry, soft, lint-free cloth for cleaning. Do not use liquids, solvents, or abrasive cleaners.
- Heat Shrink Integrity: Ensure the heat shrink remains intact and undamaged. As noted in the warnings, do not attempt to remove it.
- Storage: When not in use for extended periods, store the device in a dry, cool, and well-ventilated place, disconnected from all power sources.
8. Troubleshooting
This section addresses common issues you might encounter with your Smart Antispark Switch and provides potential solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Switch does not turn on. |
|
|
| Switch turns off unexpectedly during use. |
|
|
| Device not responding to button press. |
|
|
| Excessive heat from the switch. |
|
|
If you encounter issues not listed here or if the suggested solutions do not resolve the problem, please contact Flipsky customer support for further assistance.
9. User Tips
To enhance your experience and ensure the longevity of your Flipsky Smart Antispark Switch, consider the following general tips:
- Cable Management: Always organize your wiring neatly. Use cable ties or sleeves to bundle wires, prevent accidental disconnections, and reduce the risk of damage from vibration or abrasion.
- Environmental Protection: If using your electric vehicle in environments with high moisture, dust, or debris, consider additional protective measures for your entire electronic system, including the switch. While robust, direct exposure to harsh elements can reduce lifespan.
- System Compatibility: Always double-check that the voltage and current ratings of your battery, ESCs, and motors are well within the specifications of the antispark switch. Operating outside these limits can lead to premature failure.
- Regular Checks: Incorporate a quick visual check of your wiring and the switch into your pre-ride routine to catch any potential issues early.
10. Warranty and Support
For information regarding warranty coverage, terms, and conditions, please refer to the official Flipsky website or contact the seller directly. It is advisable to keep your proof of purchase for any warranty claims.
For technical support, troubleshooting assistance beyond this manual, or further inquiries, please reach out to Flipsky customer service through their official channels.