JIKONG V19 4.3 Inch Display

Contents

JIKONG V19 4.3 Inch Smart Touch Screen Display User Manual

Model: V19 4.3 Inch Display

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the JIKONG V19 4.3-inch Smart Touch Screen Display. This display is designed to work exclusively with JIKONG V19 series Battery Management Systems (BMS).

1.1 Product Features

  • Wide Power Supply Range: Supports a default working range of 9V to 36V.
  • Comprehensive Display Content: Shows battery total voltage, battery power, and single series voltage.
  • TTL Level Support: Baud rate defaults to 115200bps.
  • Multi-language Support: Chinese, English, Thai, and Vietnamese switchover is supported.
  • Customizable Interface: Supports language, logo, and interface customization.
JIKONG V19 4.3 Inch Smart Touch Screen Display
Figure 1: JIKONG V19 4.3 Inch Smart Touch Screen Display
JIKONG V19 4.3 Inch Display with compatible BMS models
Figure 2: The 4.3-inch display is compatible with JIKONG V19 PB series BMS models such as JK-PB1A16S10P V19, JK-PB1A16S15P V19, JK-PB2A16S15P V19, JK-PB2A16S20P V19, and JK-PB2A16S30P V19.

2. Setup Instructions

2.1 Physical Connection

The JIKONG V19 4.3-inch display connects to the BMS via a dedicated cable. Ensure all connections are secure before powering on the system.

  • User Interface Connector: This port is used for power supply and serial port signal connection. It uses a HY2.0mm-6P vertical stick socket.
  • Key Extension Interface: This port is used to control BMS startup and shutdown. It uses an A1254WF-6A vertical sticker socket.
Back of JIKONG V19 4.3 Inch Display with connectors labeled
Figure 3: Rear view of the display showing user interface and key extension connectors.
JIKONG V19 4.3 Inch Display connected to BMS via UART
Figure 4: The JIKONG V19 4.3 Inch Touch Screen Display connected to a JIKONG V19 PB Serial BMS via the UART Connector.

2.2 Pin Definition

The display end interface adopts HY2.0 mm-6P vertical mount. Refer to the table below for pin definitions:

NumberNameDefinitionNumberNameDefinition
1K-Activation signal negative electrode4TTL-RXUART RX, 5V
2K+Activate the positive signal5TTL-TXUART TX, 5V
3GNDNegative terminal6VCCDisplay power output

2.3 APP Configuration

To ensure proper communication between the display and your JIKONG BMS, you must configure the serial port protocol in the JIKONG BMS APP:

  1. Open the JIKONG BMS APP on your device.
  2. Navigate to the "Parameter Setting" page.
  3. Change the "Serial port 3 protocol" to "015-JK BMS PBxx SERIES LCD Protocol V1.0".
JIKONG BMS APP Parameter Setting for Protocol
Figure 5: JIKONG BMS APP interface for parameter setting, highlighting the serial port protocol selection.

Video 1: Demonstration of connecting the V19 4.3 inch Touch Screen to a PB series BMS and navigating its basic settings.

3. Operating Instructions

3.1 Display Interface Operation

The display provides an intuitive touch interface to monitor and configure your battery system.

3.1.1 Battery String Interface

This screen provides an overview of your battery system's status. It displays:

  • Current voltage of the battery string.
  • Current flow (charge/discharge).
  • Number of online battery packs.
  • Charging and discharging status of the entire battery string.
  • Highest and lowest cell temperatures.
JIKONG V19 4.3 Inch Display Main Screen
Figure 6: Main battery string interface showing real-time data.

3.1.2 Battery Pack Interface

In parallel mode, you can select individual battery packs to view detailed information. This screen can display up to 16 battery packs and shows:

  • Design capacity and remaining capacity of each pack.
  • Charging and discharging status of each pack.
  • Voltage of each individual cell within the pack.
JIKONG V19 4.3 Inch Display Battery Packs Screen
Figure 7: Battery pack interface displaying individual cell voltages and pack status.

3.1.3 Protocol Selection Interface

This interface allows you to select the appropriate communication protocol (RS485 or CAN) for your specific BMS setup, ensuring seamless data exchange.

JIKONG V19 4.3 Inch Display Protocol Selection Screen
Figure 8: Protocol selection interface for RS485 and CAN communication.

4. Maintenance

To ensure the longevity and optimal performance of your JIKONG V19 4.3-inch Smart Touch Screen Display, follow these general maintenance guidelines:

  • Keep the display clean using a soft, dry cloth. Avoid abrasive cleaners or solvents.
  • Protect the screen from direct sunlight and extreme temperatures.
  • Ensure all cable connections remain secure and free from damage.
  • Avoid physical impact or excessive pressure on the display.

5. Troubleshooting

If you encounter issues with your JIKONG V19 4.3-inch Smart Touch Screen Display, consider the following:

  • No Display/Power: Check all power connections and ensure the BMS is powered on. Verify the display cable is correctly inserted into both the display and the BMS.
  • Incorrect Data: Confirm that the "Serial port 3 protocol" in the JIKONG BMS APP is set to "015-JK BMS PBxx SERIES LCD Protocol V1.0".
  • Unresponsive Touch Screen: Gently clean the screen surface. If the issue persists, try restarting the BMS system.
  • Compatibility Issues: Ensure your BMS is a JIKONG V19 series model. This display is not compatible with other BMS versions.

For persistent issues, please refer to the comprehensive user manual (PDF) or contact JIKONG customer support.

6. Specifications

Detailed technical specifications for the JIKONG V19 4.3-inch Smart Touch Screen Display:

ParameterValue
Display CategoryTFT
Display Size4.3 inches
Resolution480*272
Backlight Type/BrightnessLED/300nit
Viewing Angle (L/R/U/D)85°/85°/85°/85°
Operating Temperature-20℃ to +70℃
Storage Temperature-30℃ to +80℃
Supply Voltage (Min-Max)9V - 36V (with power reverse protection)
Power Dissipation1.32W (at 12V@110mA)
Communication ProtocolTTL (default baud rate 115200bps)
Standard Cable Length0.5 meters (customizable)

6.1 Product Dimensions

JIKONG V19 4.3 Inch Display Dimensions
Figure 9: Detailed dimensions of the 4.3-inch display screen.

7. User Tips

  • Compatibility Check: Always verify that your JIKONG BMS is a V19 series model before purchasing or connecting this display. It is specifically designed for V19 BMS units.
  • Secure Connections: Ensure all wiring, especially the communication cable, is firmly connected to prevent intermittent issues or data loss.
  • Language Setting: Take advantage of the multi-language support to set the display to your preferred language for easier operation.

8. Frequently Asked Questions (FAQ)

Q: Is this display compatible with specific BMS models like PB1A16S15P, B1A8S20P, or JK-PB1A8S10P?
A: The V19 display is specifically designed for JIKONG V19 series BMS models. Please refer to the 'Specifications' section or your BMS manual for detailed compatibility information with your specific model.
Q: Does the display come with a connector cable?
A: Yes, the package includes the display and a connecting cable. The standard cable length is 0.5 meters.
Q: Is this display suitable for a 24S BMS configuration?
A: The display itself is a universal interface for JIKONG V19 BMS. Its compatibility with specific cell configurations (like 24S) depends on the capabilities of the connected JIKONG V19 BMS model. Please check your BMS specifications.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact JIKONG Official Store directly or refer to the official product documentation. A comprehensive user manual in PDF format is available for download: JIKONG V19 4.3-inch Display Operation and Maintenance Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.