ESKY EK2-0705B, 000101, 000104

Contents

ESKY 4-in-1 Gyro Receiver and Mixing Controller Instruction Manual

Models: EK2-0705B, 000101, 000104

1. Introduction

This manual provides detailed instructions for the ESKY 4-in-1 Gyro Receiver and Mixing Controller, designed for use with RC Lama V3, V4, and V5 helicopters. This unit integrates a 6-channel receiver, mixer, speed controller, and gyro into a single compact device, operating on 40MHz-41MHz frequencies. Please read this manual thoroughly before installation and operation to ensure proper function and safety.

2. Safety Precautions

  • Always disconnect power before performing any maintenance or installation.
  • Ensure correct polarity when connecting power to avoid damage to the unit and other components.
  • Operate RC models in open areas, away from people, animals, and obstacles.
  • Keep the unit dry and away from moisture.
  • This product is recommended for users aged 14 years and older.

3. Package Contents

Verify that all items are present in your package:

  • 1x ESKY 4-in-1 Gyro Receiver and Mixing Controller (Model EK2-0705B / 000104)
  • Antenna wire (integrated)
  • Power connector cable (integrated)

4. Specifications

Feature Specification
Model Numbers EK2-0705B, 000101, 000104
Frequency Band 40MHz - 41MHz (FM)
Channels 6-Channel Digital Proportional Radio Control System
Integrated Functions Receiver, Mixer, Speed Controller, Gyro
Material Composite Material
Power Source No Battery (powered by RC helicopter system)
Recommended Age 14+ years

5. Setup and Installation

Follow these steps to properly install your ESKY 4-in-1 unit into your RC helicopter:

  1. Mounting: Securely mount the 4-in-1 unit in the designated area of your RC helicopter chassis. Ensure it is protected from vibrations and potential impact.
  2. Antenna Connection: Extend the green antenna wire fully and position it away from other electronic components and carbon fiber parts for optimal signal reception.
  3. Power Connection: Connect the integrated red power connector to the helicopter's power distribution board or battery, ensuring correct polarity (red to positive, black to negative).
  4. Servo Connections: Connect the helicopter's servos (e.g., for cyclic, collective, tail rotor) to the appropriate channels on the 4-in-1 unit. Refer to your helicopter's specific wiring diagram for channel assignments. The unit has clearly labeled CH1 and CH2 ports.
  5. Motor Connection: Connect the main motor and tail motor (if applicable) to the designated speed controller outputs on the 4-in-1 unit.
Front view of ESKY 4-in-1 Gyro Receiver and Mixing Controller with CH1, CH2 labels, FM-41MHZ frequency, and model number EK2-0705B 000104.

Figure 1: Front view of the ESKY 4-in-1 unit, showing channel labels and frequency information.

Back view of ESKY 4-in-1 Gyro Receiver and Mixing Controller with GAIN, PROPORTIONAL, and LED indicators, and model number EK2-0705B 000104.

Figure 2: Back view of the ESKY 4-in-1 unit, highlighting GAIN and PROPORTIONAL adjustment points and LED indicator.

6. Operation

Once installed, follow these steps to operate your RC helicopter with the ESKY 4-in-1 unit:

  1. Transmitter Pairing: Ensure your RC transmitter is set to the correct frequency (40MHz or 41MHz) and is properly bound to the receiver. Consult your transmitter's manual for binding procedures.
  2. Power On Sequence: First, turn on your RC transmitter. Then, connect the helicopter's battery to power on the 4-in-1 unit. The LED indicator on the unit (Figure 2) should illuminate, indicating power and proper function.
  3. Gyro Calibration: Allow a few seconds for the gyro to initialize and calibrate after power-on. Keep the helicopter still during this process.
  4. Control Checks: Before flight, perform a thorough check of all controls (throttle, elevator, aileron, rudder) to ensure they respond correctly and in the proper direction.
  5. Gain Adjustment: The "GAIN" and "PROPORTIONAL" adjustments (Figure 2) allow fine-tuning of the gyro sensitivity and mixing. Adjust these settings incrementally to achieve stable flight characteristics. Higher gain generally means more stability but can lead to oscillations if too high.

7. Maintenance

  • Cleaning: Keep the unit free from dust, dirt, and debris. Use a soft, dry cloth for cleaning. Avoid using solvents or harsh chemicals.
  • Inspections: Regularly inspect all wiring and connectors for signs of wear, damage, or loose connections.
  • Antenna Care: Ensure the antenna wire is not cut, kinked, or damaged, as this can significantly reduce range and signal quality.
  • Storage: When not in use, store the unit in a dry, cool place, away from direct sunlight and extreme temperatures.

8. Troubleshooting

Problem Possible Cause Solution
No power/LED off Incorrect power connection, faulty battery, damaged unit. Check power cable polarity and connection. Test with a known good battery. Inspect unit for visible damage.
No control response Transmitter not paired, incorrect frequency, servo connections loose. Ensure transmitter is on and paired. Verify transmitter frequency matches receiver. Check all servo connections.
Unstable flight/oscillations Gyro gain too high, improper mounting, vibrations. Reduce "GAIN" setting incrementally. Ensure unit is securely mounted and isolated from vibrations.
Limited range/signal loss Antenna obstructed or damaged, interference. Ensure antenna is fully extended and clear of obstructions. Check for damage to antenna wire. Avoid flying near sources of strong radio interference.

9. User Tips

  • For optimal performance, ensure your transmitter batteries are fully charged before each flight.
  • Always perform a range check before flying, especially in new environments.
  • Start with lower gyro gain settings and gradually increase until desired stability is achieved without inducing oscillations.

10. Warranty and Support

For any issues not covered in this manual or for technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase for warranty claims. This product is covered by a standard manufacturer's warranty against defects in materials and workmanship under normal use.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.