MYAMi Adjustable DC Laboratory Bench Power Supply

Contents

Earnmee Adjustable DC Laboratory Bench Power Supply User Manual

Model: Adjustable DC Laboratory Bench Power Supply

1. Introduction

Thank you for choosing the Earnmee Adjustable DC Laboratory Bench Power Supply. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your device. Please read this manual thoroughly before use and keep it for future reference.

2. Safety Instructions

  • Always connect the power supply to a grounded outlet.
  • Ensure the input voltage matches the specified AC 220V±10%, 50/60Hz.
  • Do not operate the device in wet or damp conditions.
  • Do not open the casing; there are no user-serviceable parts inside. Refer servicing to qualified personnel.
  • Ensure adequate ventilation around the unit to prevent overheating.
  • Avoid short-circuiting the output terminals. The unit has short-circuit protection, but prolonged short circuits can cause damage.
  • Disconnect power before making any connections or disconnections.

3. Package Contents

Upon unpacking, please verify that all items are present and in good condition:

  • Earnmee Adjustable DC Laboratory Bench Power Supply Unit
  • Power Cord
  • Output Test Leads (may vary by model)
  • User Manual (this document)
Image showing the power supply unit and its packaging box.
Figure 3.1: Power Supply Unit and Packaging

4. Product Overview

4.1 Front Panel

Close-up of the front panel of the power supply, showing the digital display, voltage and current adjustment knobs, and output terminals.
Figure 4.1: Front Panel Controls
  • Digital Display: Shows Voltage (V), Current (A), Power (W), and Load Equivalent Resistance (R).
  • Voltage Adjustment Knobs (C.V.): Fine and coarse adjustment for output voltage.
  • Current Adjustment Knobs (C.C.): Fine and coarse adjustment for output current limit.
  • Power Button: Turns the unit on/off.
  • Output Terminals (Front): GND (Ground), + (Positive), - (Negative) for connecting loads. Maximum 10A output on front terminals.

4.2 Rear Panel

Rear view of the power supply, showing the cooling fan, AC power input, and main output terminals.
Figure 4.2: Rear Panel Features
  • Cooling Fan: Automatically regulates temperature. Ensure it is not obstructed.
  • AC Power Input: For connecting the main power cord.
  • Output Terminals (Rear): Main OUTPUT + (Positive) and - (Negative) terminals for higher current applications.

5. Setup Instructions

5.1 Unpacking and Placement

  1. Carefully remove the power supply from its packaging.
  2. Place the unit on a stable, level surface.
  3. Ensure there is sufficient space (at least 10 cm) around the unit for proper ventilation, especially around the cooling fan on the rear panel.
  4. Keep the unit away from direct sunlight, heat sources, and excessive dust or moisture.

5.2 Power Connection

  1. Ensure the power switch on the front panel is in the OFF position.
  2. Connect the provided power cord to the AC power input socket on the rear panel of the power supply.
  3. Plug the other end of the power cord into a grounded AC 220V±10%, 50/60Hz power outlet.

5.3 Output Connection

Use appropriate test leads for your application. For currents up to 10A, the front terminals can be used. For higher currents, use the rear output terminals.

  1. Connect the positive (+) terminal of your load to the positive (+) output terminal of the power supply.
  2. Connect the negative (-) terminal of your load to the negative (-) output terminal of the power supply.
  3. If grounding is required for your application, connect the GND terminal to the appropriate point in your circuit.

6. Operating Instructions

6.1 Power On/Off

  1. Press the red power button on the front panel to turn the unit ON. The display will illuminate.
  2. To turn OFF, press the power button again.

6.2 Voltage and Current Adjustment

  1. Voltage Adjustment: Use the C.V. (Constant Voltage) knobs to set the desired output voltage. The coarse knob makes large adjustments, while the fine knob allows for precise tuning.
  2. Current Limit Adjustment: Use the C.C. (Constant Current) knobs to set the maximum output current. This acts as a current limit to protect your load. When the load current reaches this preset limit, the power supply will switch to constant current mode.

6.3 Display Readings

The 4-bit digital display provides real-time readings of:

  • Output Voltage (V)
  • Output Current (A)
  • Output Power (W)
  • Load Equivalent Resistance (R)

6.4 Protection Features

The power supply is equipped with five powerful protection mechanisms:

  • Overload Protection for Voltage
  • Overload Protection for Current
  • Overload Protection for Power
  • Overload Protection for Temperature
  • Short Circuit Protection

These features help prevent damage to both the power supply and the connected load in case of abnormal operating conditions.

7. Maintenance

7.1 Cleaning

To maintain optimal performance and longevity, keep the unit clean:

  • Disconnect the power supply from the main power outlet before cleaning.
  • Use a soft, dry cloth to wipe the exterior of the unit.
  • Do not use abrasive cleaners, solvents, or harsh chemicals.
  • Periodically check and clean the cooling fan vents to ensure unobstructed airflow.

7.2 Storage

If storing the unit for an extended period, ensure it is kept in a suitable environment:

  • Ambient temperature: -20℃ to 80℃
  • Relative Humidity: ≤80%
  • Store in a dry, dust-free location.

8. Troubleshooting

  • No Power: Check the power cord connection to both the unit and the wall outlet. Ensure the power outlet is functional.
  • No Output Voltage/Current: Ensure the power supply is turned on. Check all output connections to the load. Verify that the voltage and current limit settings are appropriate for your application.
  • Unit Overheating: Ensure the cooling fan vents are clear and unobstructed. Operate the unit within its specified environmental conditions.
  • Unexpected Shutdown: This may indicate activation of one of the built-in protection features (overload, over-temperature, short circuit). Disconnect the load, check for faults, and restart the unit.

If problems persist, contact customer support for assistance.

9. Specifications

Input
Input voltage
AC 220V±10%,50/60Hz
Display Stability
Voltage Stability
≤±(0.2%+5digits)
Current Stability
≤±(0.5%+5digits)
Load Stability
≤0.5%
Ripple and Noise
≤1%(Valid values)
Display Resolution
Voltage Resolution
<100V:10mV;
≥100V:100mV
Current Resolution
<100A:10mA;
≥100A:100mA
Power Resolution
<10W:1mW
;≥10W:10mW;≥100W:0.1W;≥1000W:1W
Load Equivalent Resistance Display Resolution
<10R:1mR;≥10R:10mR;≥100R:0.1R;≥1000R:1R
Voltage and current value preset accuracy
Output voltage preset accuracy
0.1V
Output current stabilization preset accuracy
0.1A
Operating Environment
Elevation
Relative Humidity <80%
Ambient temperature 5℃~40℃
≤2000m
Storage environment
Ambient temperature
-20~80℃ Relative Humidity ≤80%
Communication Interface
Not standard,optional
Protection
Five powerful protection
Over load protection for voltage,current,power,temperature;and short circuit protection
Size
Product size
D330×W250×H155mm when<2400W
D410×W250×H155mm when≥2400W
Package Size
D420×W310×H220mm when<2400W
D497×W310×H220mm when≥2400W
Weight
Product net weight:
5.5kg when <2400W;8kg when≥2400W
Package weight:
6.5kg when <2400W;11kg when≥2400W

10. Warranty and Support

This Earnmee power supply comes with a 1-Year Warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support, warranty inquiries, or service, please contact your vendor or the manufacturer directly. Provide your product model and a detailed description of the issue for faster assistance.

11. User Tips

  • Proper Ventilation: To ensure the longevity and stable operation of your power supply, always ensure that the cooling fan and vents are clear of obstructions. Good airflow is crucial, especially during high-power operation.
  • Start with Low Settings: When connecting a new circuit or load, it's good practice to start with the voltage and current limits set to their lowest values and gradually increase them to the desired levels. This helps prevent accidental damage to your circuit.
  • Check Connections: Before powering on, always double-check all output connections to ensure they are secure and correctly polarized. Loose connections can lead to unstable operation or damage.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.