FLIPSKY 75200 Pro V2.0

Contents

Flipsky 75200 Pro V2.0 ESC Controller User Manual

Model: 75200 Pro V2.0

Brand: FLIPSKY

1. Introduction

This manual provides essential information for the safe and effective use of your Flipsky 75200 Pro V2.0 ESC (Electronic Speed Controller). This high-performance controller is designed for electric skateboards, scooters, and e-bikes, offering precise motor control and advanced protection features. Please read this manual thoroughly before installation and operation.

2. Warning & Safety Information

WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

  • Do not operate in rainy weather or on slippery surfaces.
  • Avoid overloading; ensure the load remains within the safe operating range.
  • Before use, inspect all accessories to confirm they are securely installed.

3. Product Overview

The Flipsky 75200 Pro V2.0 ESC Controller is a robust speed controller featuring an aluminum PCB for enhanced heat dissipation and longevity. It supports various control modes and offers comprehensive protection mechanisms for your electric vehicle.

Flipsky 75200 Pro V2.0 ESC Controller in its packaging
The Flipsky 75200 Pro V2.0 ESC Controller as received in its packaging.
Flipsky 75200 Pro V2.0 ESC Controller with power button and wiring
ESC Controller with a power button and various connection wires.
Flipsky 75200 Pro V2.0 ESC Controller with key switch and wiring
ESC Controller shown with a key switch for ignition and various wiring harnesses.
Top view of the Flipsky 75200 Pro V2.0 ESC Controller PCB
Internal view of the ESC Controller's Printed Circuit Board (PCB).

4. Specifications

Technical Specifications:

FeatureDetail
Firmware6.02, supports firmware upgrade
Voltage14-84V (safe for 4-20S)
Continuous Current50V/200A; 75V/150A (depends on mounting, ambient temperature, air/water circulation)
Burst Current300A
BEC5V@1A
Support ModesDC, BLDC, FOC (sinusoidal)
ERPM150000
Communication PortsUSB, CAN, UART, SPI, IIC
Supported SensorsABI, HALL, AS5047, AS5048A
Input Source SupportPPM, ADC, NRF, UART
Supported SensorlessYes
Regenerative CapacityYes
Programmable viaVESC_TOOL
Dimensions130x68x41mm
Motor/Power Wire Size8 AWG
Phase FilterYes
Power Switch ButtonRed

Key Features:

  • Adjustable protection against: low voltage, high voltage, over current, abnormal temperature, MOSFETs/motor over temperature.
  • Supports various control modes: Current / Duty cycle / Speed / PID.
  • Supports balancing car function by connecting IMU module via IIC interface (e.g., MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160).
  • CPU: 32F405 with frequency 168MHz.
  • Aluminum PCB for good heat dissipation and extended lifespan.
  • 75200 Pro V2.0 aluminum substrate single drive: supports single serial port function, integrates Bluetooth module (for convenient parameter connection and real-time data reading), and includes a built-in power on/off switch.

5. Setup and Installation

Follow these steps carefully for proper installation of your ESC Controller:

  1. Power Off: Always turn off the power to your electric vehicle before beginning any installation or wiring.
  2. Wiring: Install and operate strictly according to the illustrations provided in this manual. Refer to the wiring diagram below for correct connections.
  3. Testing: After installation, test all functions to verify normal operation before full use.

Wiring Diagram:

Detailed wiring diagram for Flipsky 75200 Pro V2.0 ESC Controller
Detailed wiring diagram showing connections for battery, motor, power switch, Hall sensors, PPM, CAN, USB, and COMM ports. Note: Press to unplug connectors; do not pull directly to avoid damage.

Dimensions:

Dimensions of the Flipsky 75200 Pro V2.0 ESC Controller
Physical dimensions of the ESC Controller: 130mm length, 68mm width, 41mm height.

6. Operating Instructions

Once installed, the ESC Controller manages the motor speed and direction based on your input (e.g., throttle). It supports various control modes including Current, Duty Cycle, Speed, and PID control. The controller can be programmed and configured using the VESC_TOOL software, allowing for fine-tuning of performance and safety parameters.

The integrated Bluetooth module allows for convenient connection to compatible devices to adjust parameters and monitor real-time data.

7. Maintenance

To ensure the longevity and optimal performance of your ESC Controller, observe the following precautions:

  • Do not disassemble accessories arbitrarily. Unauthorized disassembly may void warranty and cause damage.
  • Store the unit away from high temperatures, direct sunlight, and humid environments.
  • When not in use for extended periods, disconnect power and store properly to prevent battery drain or potential damage.

8. Troubleshooting

If you encounter issues with your ESC Controller, refer to the following common problems and solutions:

  • Instability after installation: Verify that all latches and connectors are fully engaged and secure.
  • Abnormal functionality: Reconnect all cables by unplugging and reinserting them firmly. Ensure no pins are bent or damaged.
  • Inability to secure firmly: Adjust screws to the appropriate tightness. Do not overtighten.

9. User Tips

  • Ensure all connections are secure and properly insulated for optimal performance and safety.
  • Regularly check for loose wires or damaged components, especially after heavy use.

10. Frequently Asked Questions (FAQ)

Q: What should I do if the controller stops working after a short period?
A: First, check all cable connections to ensure they are firmly seated. Also, verify the power supply and battery connections are correct and providing adequate power. If the issue persists, refer to the troubleshooting section or consult the full user manual PDF.
Q: How do I identify the battery plug?
A: Please refer to the detailed wiring diagram provided in Section 5 of this manual for the correct battery connection points and associated labels.

11. Warranty & Support

For detailed warranty information and further technical support, please refer to the official Flipsky website or contact your retailer. A comprehensive user manual in PDF format is also available for download:

Download User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.