Diatone MAMBA MK4 F722 APP

Contents

Diatone MAMBA MK4 F722 APP Flight Controller & ESC Stack Instruction Manual

Model: MAMBA MK4 F722 APP | Brand: Diatone

1. Introduction

This manual provides detailed instructions for the installation, setup, and operation of your Diatone MAMBA MK4 F722 APP Flight Controller and ESC Stack. This high-performance stack features an F722 flight controller with MPU6000 gyroscope, OSD, 5V/9V BEC, and a 45A, 55A, or 65A 3-6S 128K BL32 Brushless ESC, designed for FPV drone applications. Please read this manual thoroughly before use to ensure proper functionality and safety.

2. Package Contents

Upon opening the package, you should find the following items:

  • Diatone MAMBA MK4 F722 APP Flight Controller
  • Diatone MAMBA F45/F55/F65 128K BL32 Brushless ESC (depending on selected variant)
  • Connection cables and wires
  • Mounting hardware (screws, nuts, standoffs)
  • Capacitor (recommended for 6S battery use)
  • Diatone stickers

Refer to the unboxing video below for a visual guide to the package contents:

Video: Unboxing the Diatone MAMBA MK4 F722 APP Flight Controller and ESC Stack, showing all included components.

3. Specifications

3.1. Flight Controller (MAMBA MK4 F722 APP)

Diatone MAMBA MK4 F722 APP Flight Controller Specifications

Image: Detailed specifications for the Diatone MAMBA MK4 F722 APP Flight Controller, including MCU, Gyro, OSD, Blackbox, UARTs, Receiver support, BEC outputs, and mounting dimensions.

Flight Controller Specifications
FeatureSpecification
MCUSTM32F722
Frequency216MHz
GyroBMI270
OSDAT7456E
Blackbox16M Memory
UARTs6 Set
ReceiverTBS/SBUS/IBUS/DSM
I2CYes
F.PortYes
Buzzer PadYes
CURR PadYes
ESC Signal8 Set
BEC 3.3V0.5A
BEC 5V3A
BEC 9V3A
MB LEDYes
BF LEDYes
AIR UNIT PortYes
WIFISpeedyBee APP
VTX SwitchYes
BEC ProtectionYes
Receiver ProtectionYes
TVS ProtectionYes
Input6S Lipo
SoftwareBetaflight
Mounting30.5x30.5mm/M3
Size38.0x40.5x8mm
Weight10g

Default Port Assignments:

  • UART 1: Receiver
  • UART 2: Vacancy
  • UART 3: VTX
  • UART 4: WIFI
  • UART 5: Vacancy
  • UART 6: TELE

Target Firmware:

  • Main firmware: STM32 F7X2
  • Config file: MAMBA F722_2022A

3.2. ESC (MAMBA F45/F55/F65 128K)

Diatone MAMBA F45 F55 F65 128K ESC Specifications

Image: Specifications for MAMBA F45, F55, and F65 128K ESCs, detailing current ratings, input voltage, BLHeli version, and mounting.

ESC Specifications (MAMBA F45_128K)
FeatureSpecification
CURRYes
TelemetryYes
Output Current45A
Peak Current55A
Input3-6S Lipo
BLHeliBLHeli_32
PWM24-128K
TargetMAMBA F45_128K
ProtocolDshot 300/600/1200
Mounting30.5x30.5mm, Ø 3
Size44.5x40.0x7.5mm
Weight15g
ESC Specifications (MAMBA F55_128K)
FeatureSpecification
CURRYes
TelemetryYes
Output Current55A
Peak Current65A
Input3-6S Lipo
BLHeliBLHeli_32
PWM24-128K
TargetMAMBA F55_128K
ProtocolDshot 300/600/1200
Mounting30.5x30.5mm, Ø 3
Size44.5x40.0x7.5mm
Weight15g
ESC Specifications (MAMBA F65_128K)
FeatureSpecification
CURRYes
TelemetryYes
Output Current65A
Peak Current75A
Input3-6S Lipo
BLHeliBLHeli_32
PWM24-128K
TargetMAMBA F65_128K
ProtocolDshot 300/600/1200
Mounting30.5x30.5mm, Ø 3
Size44.5x40.0x7.5mm
Weight15g

4. Setup and Wiring

Careful wiring is crucial for the proper function and longevity of your flight controller and ESC stack. Please follow the diagrams and instructions below.

4.1. Main Wiring Diagram

Diatone MAMBA MK4 F722 APP Flight Controller Wiring Diagram

Image: Comprehensive wiring diagram for the Diatone MAMBA MK4 F722 APP Flight Controller, showing connections for receiver (TBS Crossfire Nano, MSR Receiver), GPS, VTX (MAMBA TX500, MAMBA ULTRA TINY), LED strip, and buzzer. Also includes LED control instructions.

4.2. VTX Power Control

Before wiring, please check the voltage. The VTX power switch channel is USER1, connected by default. Configure the power on or off after setting the channel.

VTX Power Control Wiring and Betaflight Commands

Image: VTX power control wiring diagram, showing connections for 9V and 3-6S VCC, along with Betaflight CLI commands for configuration.

Betaflight Commands for VTX Power Control:

  1. Configure USER 1 function in Betaflight command line:resource PINIO 2 C007 (Configure C007 as PINIO function)set pinio_config = 129,129,1,1 (Set the VTX power to be turned on by default)set pinio_box = 0,40,255,255 (Set PINIO 2 function range)save (Save the configuration and restart the FC)
  2. Correspond USER1 to the AUX Channel of the remote control (as shown in the image).

4.3. Capacitor Connection

A capacitor is requested when using a 6S battery to help filter power and protect components.

Capacitor Connection and ESC Amperage Meter Settings

Image: Diagram showing the correct polarity for connecting a 35V 470uF capacitor to the ESC, along with recommended Amperage Meter settings for different ESC variants.

4.4. Motor Direction

Ensure your motors are spinning in the correct direction for stable flight. The diagram below illustrates the standard motor rotation for a quadcopter.

Motor Direction Diagram and Power Indicator

Image: Diagram showing the recommended motor rotation for a quadcopter (Motor 1, 2, 3, 4) and a legend for the power indicator LEDs (GYRO, MCU, 9V, 5V, 3.3V, VCC).

4.5. Power Indicator

The power indicator LEDs provide visual feedback on the status of the BEC. Please follow the flight control sequence.

Power Indicator LED Status
LEDColorFunction
GYROBlueGyroscope status
MCUOrangeMicrocontroller status
9VGreen9V BEC status
5VWhite5V BEC status
3.3VRed3.3V BEC status
VCCGreenMain power input status

4.6. LED Control

The LEDs on the flight controller can be controlled via Betaflight when the upper pads are shorted. The LEDs are controlled by the Mamba LED Control System (on Board) when the lower pads are shorted.

Mamba LED Control Instructions
ActionFunction
Click one timeChange color
Double clickFlash mode
Press and holdOn/Off

5. Operating Instructions

The Diatone MAMBA MK4 F722 APP Flight Controller operates on Betaflight firmware. After completing the physical installation and wiring, you will need to configure the flight controller using the Betaflight Configurator software on your computer.

5.1. Betaflight Configuration

  • Firmware Flashing: Ensure you have the correct Betaflight firmware (Target: MAMBA F722_2022A) flashed to your flight controller.
  • Port Configuration: Configure UARTs for your receiver, VTX, GPS, and other peripherals according to the default port assignments or your custom setup.
  • ESC Protocol: Set the ESC protocol to Dshot 300/600/1200 in Betaflight.
  • Motor Direction: Verify motor direction in the Motors tab of Betaflight Configurator. Adjust using BLHeliSuite32 if necessary.
  • OSD Setup: Customize your On-Screen Display (OSD) elements to show flight data, battery voltage, and other critical information.
  • PID Tuning: Perform initial PID tuning for stable flight. Further fine-tuning can be done in the field.

5.2. Mobile App Configuration (SpeedyBee APP)

The integrated WiFi module allows for convenient wireless configuration using the SpeedyBee APP. Download the app on your smartphone and connect to the flight controller's WiFi network to adjust settings, check sensor data, and flash firmware without a computer.

6. User Tips

  • Soldering Pads: The large soldering pads on this stack make it easier for both beginners and experienced users to make clean connections. Take your time and ensure strong, isolated solder joints.
  • Capacitor for 6S: Always use the recommended capacitor when powering the stack with a 6S LiPo battery to prevent voltage spikes and protect sensitive electronics.
  • Firmware Updates: Regularly check for the latest Betaflight firmware and BLHeli_32 firmware updates to benefit from performance improvements and bug fixes.
  • Wiring Cleanliness: Keep your wiring as neat and tidy as possible to avoid interference and potential shorts. Use heat shrink and zip ties where appropriate.

7. Troubleshooting

  • No Power: Double-check all power connections, battery voltage, and ensure the main power lead is correctly soldered to the ESC. Verify BEC output voltages using a multimeter.
  • Motors Not Spinning: Ensure ESCs are armed, motor direction is correct in Betaflight/BLHeliSuite32, and ESC protocol is properly configured. Check for continuity in motor wires.
  • No Receiver Input: Verify receiver wiring to the correct UART, ensure the receiver protocol (e.g., SBUS, Crossfire) is selected in Betaflight, and that your radio is bound to the receiver.
  • OSD Not Displaying: Check OSD settings in Betaflight. Ensure your FPV camera and VTX are correctly wired to the flight controller.
  • Unstable Flight: This could be due to incorrect motor direction, improper PID tuning, or vibrations. Start with default Betaflight PIDs for your frame size and tune incrementally. Check for loose components or damaged propellers.
  • WiFi Connection Issues: Ensure the SpeedyBee APP is up to date. Try restarting the flight controller and your phone's WiFi.

For more in-depth troubleshooting, refer to the official Betaflight documentation and community forums.

8. Warranty and Support

For any technical issues, warranty claims, or support inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase. Diatone provides support for their products, and detailed information can often be found on their official website or community channels.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.