Introduction
Thank you for purchasing the BAOFENG UV-21M Multi Band Walkie Talkie. This dual-band, dual-display, and dual-watch radio is designed to provide secure, instant, and reliable communications. It features Bluetooth Phone APP programming, Type-C charging, a 1.77-inch color screen, and NOAA weather alerts. This manual provides detailed instructions to help you maximize the performance and ensure safe operation of your device.
For additional information, you may refer to the User Manual (PDF).
Safety and Regulatory Information
FCC Regulatory Conformance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
Compliance with RF Exposure Standards
To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key.
- Keep the radio unit at least 2.5cm away from the face.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
Operating Prohibitions
To protect against property loss, bodily injury or death, observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Product Overview
The BAOFENG UV-21M is a multi-band walkie talkie with a 1.77-inch color screen and a full keyboard for open menu operation. It supports various features including wireless APP programming, multi-band scanning, and NOAA weather radio reception.
Figure 1: BAOFENG UV-21M Walkie Talkie highlighting multi-band, wireless APP programming, and 1000 channels.
Key Features
- 1.77" TFT large color screen, full keyboard, fully open menu operation
- Multi-band scanning receiver: FM: 65-108MHz(RX), AM: 108-136MHz(RX), 136-174MHz(TX&RX), 220-260MHz(TX&RX), 350-390MHz(RX), 400-480MHz(TX&RX), 480-520MHz(RX)
- Bluetooth Phone APP Wireless Programming (iOS & Android compatible)
- Wireless Copy Frequency function
- 1000 Memory Channels
- Type-C and Base Desktop Charging methods
- NOAA Weather Radio Channel Reception and Weather Alerts
- LED Flashlight
- VOX (Voice Activated Transmit) Function
- Emergency Alarm Function
- Scanner Function (VFO scan, channel scan, CTC/DCS scan)
- Battery Saving Function
- DTMF Encoder and Manual Dial
- PC Programmable
- One-touch frequency search
Radio Components
Figure 2: Front, side, and top views of the UV-21M with labeled components.
- Antenna
- PTT key
- SK1: Customized key
- SK2: Power select/Emergency Alert key
- SK3: FM broadcast/Monitor key
- LED flashlight
- MENU key
- VFO/MR key
- Numeric keypad
- Power / Volume knob
- Color LCD
- Accessory jack
- EXIT Key
- A/B key
- Navigation keys
- Speaker
- LED Status Indicator
- Type-C charging indicator
- Type-C charging port
- Battery tightening screw
Setup
Package Contents
The following items are included in your BAOFENG UV-21M package:
Figure 3: Standard packing list including radio, antenna, battery, chargers, clip, lanyard, and manual.
- 1 Radio body
- 1 Lithium-Ion battery pack
- 1 Instruction Manual
- 1 Belt Clip
- 1 Desk charger (With wall-wart)
- 1 Antenna
- 1 Wrist Belt
- 1 Type-C Charger Cable
*If any item is missing, please notify your Baofeng / Pofung dealer.
Battery Installation / Removal
Installing the Battery Pack
- Position the battery pack over the back of the radio.
- Engage the battery pack into the radio until it is fully seated into the radio housing.
- Tighten the screws using a coin or appropriate object to secure the battery pack to the radio. Do not overtighten.
Removing the Battery Pack
- Loosen the screws on the back of the battery pack.
- Lift the bottom of the battery pack slightly to remove it from the radio housing.
- Pull the battery pack out of the radio housing.
Note: The Li-ON battery pack can also be charged in the battery charger.
Antenna Installation / Removal
Installing the Antenna
- Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
Removing the Antenna
- Turn the antenna counter-clockwise to remove it.
Belt Clip Installation / Removal
Installing the Belt Clip
- Place the belt clip above the corresponding holes on the back of the radio, and screw it into place clockwise with the two supplied screws.
Removing the Belt Clip
- Unscrew counter-clockwise to remove the belt clip.
Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
Operating Instructions
Battery Charging
The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge/discharge the battery two or three times before regular use.
Figure 4: The UV-21M supports both Type-C direct charging and traditional base charging.
How to Charge
- Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange, indicating it's ready to charge.
- Plug the battery or the radio into the charger. Ensure good contact with charging terminals. The indicator light turns red.
- A full charge takes approximately 2-5 hours. When the lamp lights green, charging is complete.
- For Type-C direct charging, plug the Type-C cable into the port on the battery and the other end into a power source (wall adapter, power bank, PC, car charger). An empty battery will be fully charged in 6 hours.
Note: The radio should be turned OFF during the charge cycle for proper indicator function.
LED Indicator Status
| Red LED | Green LED | Status |
|---|---|---|
| Flashing | Steady | Standby (charger empty) / Error (charger with radio) |
| Steady | Off | Charging |
| Off | Steady | Charge complete. |
Basic Operations
Power On/Off
- To Turn On: Rotate the Volume/Power knob clockwise until you hear a "click". An audible double beep and display message/flash will indicate power-on.
- To Turn Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".
Adjusting the Volume
Rotate the Volume/Power knob clockwise to increase volume, and counter-clockwise to decrease. Use the monitor function (press and hold the SK3 key) to adjust volume against un-squelched static.
Main Band/Sub Band Switch
In standby mode, press the [A/B] key to switch between the main frequency band (large font on display) and sub frequency bands (small font).
VFO/Channel Switch
Press the [VFO/MR] key to switch between VFO (Frequency) mode and Channel (MR) mode. 'VFO' or the channel number will be displayed on the right.
Frequency (VFO) Mode
In VFO mode, navigate up/down the band using the ▲ or ▼ keys. Frequencies can also be input directly using the numeric keypad (e.g., for 436.61250 MHz, enter [4][3][6][6][1][2][5][0]).
WARNING: Transmitting on unauthorized frequencies is illegal. Always ensure you have the necessary license.
Channel (MR) Mode and Channel Selection
Channel (MR) mode is practical for everyday use with pre-programmed channels. Navigate channels using the ▲ or ▼ keys or by inputting channel numbers directly (e.g., for channel 12, input [0][1][2]).
Selecting a Bank
The radio supports up to 10 banks, each with a maximum of 100 channels. Press the MENU key, navigate to 'Bank', select a bank using ▲ or ▼, then press MENU to confirm.
Making a Call
- Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. The red LED will be on.
- Frequency Mode Call: Press [VFO/MR] key to switch to frequency mode, input the desired frequency, then hold down the [PTT] key to transmit.
- Receive a Call: Release the [PTT] key. The green LED will be on when receiving a call.
Note: Keep the microphone 2.5 cm to 5 cm from your mouth for best reception volume.
Emergency Alert
To activate, press and hold the [SK2] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK2] again to exit. WARNING: Use only in actual emergencies.
Using the Flashlight
If SK1 is defined as a LAMP function, press [SK1] once for continuous light, press again for strobe emergency mode, and press a third time to turn off.
FM Radio (FM)
The radio can receive FM broadcasts from 65-108MHz. Press [SK3] to turn on/off the radio. Select frequency with ▲ or ▼ keys or input directly. Press #z to automatically search for a station.
Monitor Function
In standby, press and hold the [SK3] key to enter Monitor mode to listen to weak signals. Release [SK3] to return to standby.
Keypad Lock
To enable/disable, press and hold the * key for about two seconds. The keypad can also be set to lock automatically after ten seconds via the menu.
Weather Radio/Scan Weather Channel (NOAA)
The radio has a NOAA Weather Radio function to receive weather reports and scan all 10 channels. To turn on NOAA Weather Scan, press and hold the MENU key for 3 seconds. The L icon will appear. Press and hold #2 for 3 seconds to start automatic scanning. After stopping the scan, manually select channels with ▲ or ▼. Exit with MENU or [PTT] key.
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| CH-01 | 162.550 | CH-06 | 162.500 |
| CH-02 | 162.400 | CH-07 | 162.525 |
| CH-03 | 162.475 | CH-08 | 161.650 |
| CH-04 | 162.425 | CH-09 | 161.775 |
| CH-05 | 162.450 | CH-10 | 163.275 |
Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
One Touch Frequency Search
Define SK1 as a Search function via CPS software or radio menu. Briefly press SK1 to activate search. The radio will display the received frequency and any CTCSS/DCS values. Press MENU to save the frequency and CTCSS/DCS to a channel.
Figure 5: Visual representation of the One Key Frequency Match feature.
Advanced Features
Scanner
The radio has a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. To enable, press and hold #2 for about two seconds. Change scanning direction with ▲ or ▼. Press and hold #2 to exit.
- Frequency Ranger: In frequency mode, precisely set the sweep range (e.g., 144.000-146.000MHz).
- Scan Modes:
- Time Operation (TO): Scanner stops on signal, resumes after a preset timeout.
- Carrier Operation (CO): Scanner stops on signal, resumes after a preset time with no signal.
- Search Operation (SE): Scanner stops when it detects a signal. Press and hold #z again to resume.
- Scan Sub-Code (CTCSS/DCS): Search for CTCSS or DCS codes on a known frequency.
- Sub-Code Scan Storage: Store scanned CTCSS/DCS codes as TX, RX, or both for current channel/frequency mode.
DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method used for automation systems and remote control, common in amateur radio repeaters. The radio supports full DTMF implementation.
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
To send DTMF codes, press the corresponding key(s) while holding down the PTT key.
Dual Watch
The radio features Dual Watch functionality, allowing you to monitor two channels simultaneously. To enable/disable, press MENU, enter '4' (Radio Settings), then '15' (Dual Watch). Use ▲ or ▼ to select ON/OFF, then MENU to confirm.
Manual Programming (Channels Memory)
The radio supports 10 zones / 1000 memory channels. Channels can be programmed with receive/transmit frequencies, power, signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.
Menu Functions
Basic Use of Menus
- Press the MENU key to enter the main menu.
- Use the ▲ or ▼ keys to navigate between menu items.
- Press MENU again to select a desired item.
- Use ▲ or ▼ to navigate between parameters.
- Press MENU to confirm selection and return to the main menu.
- Press the PTT key to exit the menu at any time.
Using Shortcuts
Each menu item has a numerical value for direct access. Press MENU, enter the menu item number using the numeric keypad, then press MENU to enter. Parameters can be selected with ▲ or ▼ or by numerical shortcut code.
Radio Settings (MENU + 1 to MENU + 19)
- Step frequency (MENU + 1): Select frequency step (2.5K to 100K). Not modifiable in channel mode.
- Squelch level (MENU + 2): Adjust squelch from OFF (open) to Level 5 (highest).
- Power save (MENU + 3): Reduces battery consumption in standby.
- VOX Function (MENU + 4): Activates voice-activated transmit (hands-free calls). ON/OFF.
- VOX Level (MENU + 5): Select VOX sensitivity (1-9, 1 least sensitive).
- VOX Delay (MENU + 6): Sets delay for VOX transmission (0.5-2.0 seconds).
- Time-Out-Timer (TOT) (MENU + 7): Sets max continuous transmission time (15-180 seconds, or OFF).
- Transmission Overtime Alarm (TOA) (MENU + 8): Alerts before TOT terminates transmission (0-10 seconds).
- Voice prompts function (MENU + 9): Activates voice prompts for operations.
- Language selection (MENU + 10): Select LCD display and operation prompt language.
- Roger beep (MENU + 11): Radio beeps when PTT is released.
- Keypad beep (MENU + 12): Keypad emits a beep tone when pressed.
- Backlight (MENU + 13): Adjusts display backlight auto-off time (5S-20S or Always).
- Power on image (MENU + 14): Sets display mode when radio powers on (PICTURE, MESSAGE, VOLTAGE).
- Dual Watch Operation (MENU + 15): Activates dual watch.
- Auto Keypad Lock (MENU + 16): Keypad locks automatically after 10s.
- Alarm Mode (MENU + 17): Sets tone alarm/code alarm/site alarm.
- Local Alarm Tone (MENU + 18): Emits local alarm whistle when emergency alarm is triggered.
- ANI-ID (MENU + 19): Displays/edits ANI code (up to 5 digits).
Program Channel (MENU + 1 to MENU + 13)
Channel configuration allows modification of channel name, frequencies, CTCSS/DCS, scan list addition, working mode, and channel memory/delete.
- Channel name (CHNAME) (MENU + 1): Edit channel name (up to 8 alphanumeric characters).
- RX Frequency (MENU + 2): Input Receive frequency.
- TX Frequency (MENU + 3): Input Transmit frequency.
- Transmit power (Tx Power) (MENU + 4): Set High or Low power for current channel.
- Wide/Narrow Bandwidth (MENU + 5): Select 25 KHz (Wide) or 12.5 KHz (Narrow).
- Receiving CTCSS (Rx CTCSS) (MENU + 6): Add CTCSS codes for private channels.
- Receiving DCS (Rx DCS) (MENU + 7): Add DCS codes for private channels.
- Transmitting CTCSS (Tx CTCSS) (MENU + 8): Set CTCSS tone in transmit mode.
- Transmitting DCS (Tx DCS) (MENU + 9): Activate DCS codes in transmit mode.
- Call Encryption (Encryption) (MENU + 10): Enables encryption for private conversations (requires matching DCS code).
- Signal code (Signaling) (MENU + 11): Selects 1 of 20 DTMF codes (programmed via software).
- Working Mode (CH-MDF) (MENU + 12): Set display mode (NAME, FREQ, CH).
- Monitor (SP-MUTE) (MENU + 13): Activates monitor feature based on QT/DTMF detection.
- Scan Add (Scan Add) (MENU + 14): Add current channel to scan group (On/Off).
- Busy Channel Lock (Busy Lock) (MENU + 15): Prevents transmission if channel is busy.
- Channel Memory (CH-Memory) (MENU + 16): Create or modify existing channels (1-1000).
- Channel Delete (CH-Delete) (MENU + 17): Delete programmed information from a specified channel.
Radio Info
Displays the Radio ID, firmware version, and hardware version.
Wireless Programming Radio (Bluetooth)
The UV-21M supports reading and writing frequencies via Bluetooth using the BAOFENG radio APP. Download and install the APP on your Android or iOS device. Open the APP, enable Bluetooth and location services, select 'Baofeng' brand and 'UV-21M' model, connect to the radio, then use the APP to program channel information, frequency mode, and optional functions.
Figure 6: The mobile application interface for wireless programming.
Maintenance
Battery Maintenance
- Only charge batteries at normal room temperatures (5℃~40℃).
- Turn off the radio when charging a battery attached to it for faster charging.
- Do not unplug the power or remove the battery/radio before charging is complete.
- Never charge a wet battery.
- Replace the battery if operating time significantly shortens.
- In cold environments, keep a spare battery warm (e.g., inside your jacket).
- Regularly wipe accumulated dust from charging contacts with a clean, dry cloth.
- If the battery becomes wet, remove it, wipe dry, and place it in a plastic bag with dry rice overnight.
How to Store the Battery
- Store batteries at approximately 80% discharged.
- Keep in a low temperature and dry environment.
- Keep away from hot places and direct sunlight.
- Cycle the battery at least every six months to avoid severe capacity degradation during long-term storage.
- Do not short circuit battery terminals.
- Never attempt to remove the casing from the battery pack.
- Do not store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire.
Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | Battery installed improperly, power run out, poor contact, low voltage. | Remove/reattach battery, recharge/replace battery, clean contacts. |
| During receiving, the voice is weak or intermittent. | Volume level low, antenna loose/incorrectly installed, speaker blocked. | Increase volume, turn off radio then reattach antenna, clean speaker. |
| You cannot communicate with other group members. | Frequency/signaling type inconsistent, too far from members. | Verify TX/RX frequency/signaling type, move towards members. |
| You hear unknown voices or noise. | Interrupted by other radios, radio in analog mode with no signaling. | Change frequency, adjust squelch level, set signaling. |
| You are unable to hear anyone because of too much noise and hiss. | Too far from members, unfavorable position (blocked by buildings/underground), external disturbance. | Move towards members, move to open area, restart radio, stay away from interference. |
| The radio keeps transmitting. | VOX turned on or headset not installed. | Turn off VOX function, check headset. |
Note: If these solutions do not resolve your problems, please contact your dealer for technical support.
Specifications
| General | |
|---|---|
| Channel Capacity | 1000 |
| Channel Spacing | 25.0 KHz/12.5 KHz |
| Input Voltage | 7.4 V DC |
| Battery Life (5% TX, 5% RX, 90% Standby) | Li-on: 12 hours @5 watts |
| Operating temperature | -10°C to 60°C |
| Antenna Impedance | 50Ω |
| Radio Dimensions | 143mm X 64mm X 41mm (not including antenna) |
| Radio Weight | 298 g (with Li-ON battery) |
| Transmitter | |
| Frequency Range (TX) | 136-174MHz, 220-260MHz, 400-480MHz* |
| Modulation | 16K0F3E/11K0F3E |
| Spurious Emission | -16 dBm<1GHz, -16 dBm>1GHz |
| Frequency Stability | ±2.5 ppm |
| Audio Distortion | ≤5% |
| FM Hum & Noise | 40 dB |
| Receiver | |
| Frequency Range | 108-136, 136-174, 220-260, 350-390, 400 to 520 MHz (Scan Receiver)* |
| Sensitivity: 12 dB SINAD | -120 dBm |
| Adjacent Channel Selectivity | -60 dBm |
| Intermodulation and Rejection | -70 dBm |
| Rated Audio Power Output | 0.75 Watts @ 16 Ω |
| Rated Audio Distortion | ≤5% |
Note: All specifications may be modified without prior notice or liability. *This frequency range is the hardware design frequency, the actual usable frequency must strictly comply with the regulatory requirements of your country and region.
User Tips
- Always ensure you have the proper licensing for transmitting on specific frequencies in your region.
- When programming the radio, it's recommended to read the factory software data first, then rewrite with your desired frequencies to avoid errors.
- For optimal battery life, perform a full charge/discharge cycle two to three times when first using a new battery or after extended storage.
- Keep the radio's charging contacts clean to ensure efficient charging.
- If you experience weak or intermittent voice reception, check your antenna connection and adjust the volume.
- The Bluetooth APP programming feature offers a convenient way to manage frequencies without physical cables, making it easier to customize your radio on the go.
Warranty and Support
For technical support or if you encounter any issues not covered in this manual, please contact your BAOFENG / Pofung dealer. Refer to the provided PDF user manual for comprehensive details and additional information.
PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
Website: www.baofengradio.com / www.pofungshop.com