LEXON LUST AL7005 Track Frame Set

Contents

LEXON LUST AL7005 Track Frame Set User Manual

Model: LUST AL7005 Track Frame Set

Brand: LEXON

Introduction

This manual provides essential information for the safe assembly, operation, and maintenance of your LEXON LUST AL7005 Track Frame Set. Please read all instructions carefully before proceeding with assembly or use. Proper assembly and maintenance are crucial for your safety and the longevity of the product.

Critical Safety Warnings

Failure to follow these warnings could result in serious injury or death.

  • Torque Wrench is Mandatory: You MUST use a calibrated torque wrench for all components (stem, seatpost, derailleur, bottle cages). Over-tightening can cause immediate or progressive carbon fiber failure. Never exceed the maximum torque values printed on the frame.
  • Verify Compatibility Before Installation: Installing incompatible parts can damage the frame.
    • Fork/Steerer Tube: Ensure the fork steerer diameter matches your frame's head tube (e.g., 1-1/8" for most road).
    • Bottom Bracket: Match the crankset spindle type (24mm or 29mm) and the frame's BB standard (e.g., BB86 for road, BB92/PF30 for MTB).
    • Wheels: Ensure hub width (e.g., 142x12mm for MTB, 100/130mm for road) and type (quick-release or thru-axle) are correct.
  • No Modifications: Do NOT drill, cut, sand, or attempt to repair any part of the carbon frame. This voids the warranty and compromises structural integrity.
  • Post-Crash Inspection: After any crash, impact, or hard drop, the frame must be inspected by a professional. Internal damage may not be visible. Stop using the bike immediately if you find any cracks, deep scratches, creaking sounds, or visual deformation.
Page from LEXON Carbon Frame Manual showing critical safety warnings and care instructions.
Original manual page detailing safety warnings and care instructions.

Specifications

The LEXON LUST AL7005 Track Frame Set is designed for performance and durability. Key specifications are detailed below:

LEXON LUST AL7005 Frame Set Specifications
FeatureDetail
Model NumberLUST
MaterialAL7005 Triple Butted Tube (Aluminum/Alloy)
Weight (51cm frame + fork)1565g (frame) + 430g (fork)
Headsets1 1/8"*42-52MM*39.8MM (Tapered)
BB TypeBSA68, English Thread
Seat Post Diameter31.6mm
Available Sizes (C-T)490MM, 510MM, 540MM, 560MM, 580MM
Maximum Tire Size700C*28C
Maximum Chainwheel175-52T
ForkFull Carbon Fork (TORAY T800)
Surface ProcessingPainted, Full Smooth Painting, Hand Polished Welds
Detailed specification table for LEXON LUST frame set.
Detailed specifications for the LEXON LUST frame set.
Close-up of full carbon fork and tapered head tube with dimensions 41.8mm and 52mm.
Full Carbon Fork and T-Head Tube dimensions.
Frame geometry table with measurements for X-Small, Small, Medium, Large, X-Large sizes.
Frame geometry table for various sizes.

Package Contents

Upon receiving your LEXON LUST AL7005 Track Frame Set, please verify that all the following components are included:

  • 1 x Frame
  • 1 x Fork (Full Carbon)
  • 1 x Seat Clamp
  • 1 x Headset

Assembly Instructions

For your safety, the initial build and any major service should be performed by a certified bicycle mechanic familiar with modern carbon fiber frames.

Preparation

  • Clean all contact surfaces thoroughly before assembly.
  • Apply a carbon fiber assembly paste to the seatpost, stem clamp area (if carbon), and bottom bracket shell threads (if threaded) to ensure proper grip and prevent seizing.

Headset and Bearing Installation

  • Use a proper bearing press tool and correct-sized adapters for headset and bearing press-fit installation.
  • Ensure bearings are pressed in straight, not at an angle, to prevent damage to the carbon head tube or bottom bracket shell.

Component Mounting

  • Seatpost: Insert the seatpost to at least the minimum insertion mark. Use the frame's specified clamp and torque settings.
  • Derailleur Hanger: Install the correct model-specific hanger and torque gently (usually 5-8 N·m).
  • Internal Cable Routing: Use foam sleeves or guide kits to prevent rattling and protect the inner walls of the frame.
Close-up of caliper brake and frame detail, showing brake mounting area.
Detail of caliper brake mounting area on the frame.
Close-up of hand-polished welds on the bicycle frame, indicating quality craftsmanship.
Example of hand-polished welds on the frame.

Operating Your Fixed Gear Bicycle

A fixed gear bicycle, also known as a fixie, operates differently from a freewheel bicycle. The pedals are directly connected to the rear wheel, meaning if the wheel is moving, the pedals are moving. This requires a different riding technique and constant pedal engagement.

  • Constant Pedaling: Be prepared for continuous pedaling as long as the bike is in motion.
  • Braking: While some fixed gear bikes are ridden brakeless, it is highly recommended to install at least a front brake for safety. Braking can also be achieved by resisting the pedal motion (skidding), but this requires practice and can wear tires quickly.
  • Cornering: Be mindful of pedal strike when cornering, as pedals continue to rotate.
  • Starting and Stopping: Practice starting and stopping in a safe, open area to get accustomed to the direct drive.

Care, Inspection & Maintenance

Cleaning

  • Use a soft cloth, mild soap, and water for cleaning.
  • Do NOT use a high-pressure washer, steam cleaner, or harsh solvents, as these can damage the frame's finish and components.
  • Avoid directing water into bearing areas or internal ports.

Storage

  • Store your bicycle in a cool, dry place.
  • Keep it away from direct sunlight and sources of extreme heat (e.g., a car trunk in summer) to prevent material degradation.

Regular Inspection

Perform a visual and tactile check before important rides. Pay close attention to the following key areas:

  • Stress Points: Inspect around all dropouts, bottom bracket shell, head tube junctions, and seat cluster for any signs of stress or damage.
  • Clamp Areas: Check where the stem, seatpost, and bottle cages contact the frame for proper torque and any signs of slippage or wear.
  • Frame Surface: Look for any cracks, chips, discoloration, or fraying carbon fibers, especially on the fork.

Professional Service

We recommend a full safety inspection by a qualified bicycle mechanic at least once a year or after every 5,000 km of riding, whichever comes first.

Troubleshooting

  • Fork/Headset Gap: If there is an unexpected gap between the fork and the frame, ensure the headset components are correctly installed and seated. Replacing the support ring or lower bearing with a compatible size might resolve the issue.
  • Brake Installation on Fork: The carbon fork is thick. If you plan to install a front brake, you may need to purchase a longer brake nut (e.g., a long Erixon nut) to ensure proper and secure attachment. Attempting to force an incompatible brake nut can damage the fork.
  • Creaking Sounds: Creaking sounds can indicate loose components, insufficient grease/assembly paste, or frame damage. Inspect all bolted connections, especially around the bottom bracket, seatpost, and headset. If the sound persists or you suspect frame damage, cease use immediately and consult a professional mechanic.

User Tips

  • Brake Nut for Carbon Fork: When installing a front brake on the carbon fork, be aware that the fork is thick. A standard brake nut might not be long enough. Consider purchasing a longer Erixon nut or similar extended brake nut for secure installation.
  • Headset Adjustment: If you notice a gap or play in the headset, double-check the installation of all headset components, including spacers and bearings. Minor adjustments or replacing specific rings might be necessary for a snug fit.
  • Professional Assembly: Given the lightweight and specialized nature of this frame, professional assembly by an experienced bike mechanic is highly recommended to ensure all components are correctly installed and torqued to specification.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact LEXON customer service or refer to the official LEXON website. Keep your purchase records for any warranty claims.

Additional Resources

A detailed user manual in PDF format is available for download:

View User Manual (PDF)

© 2025 LEXON. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.