Conentool Cordless Strimmer User Manual

1. Introduction

This manual provides essential information for the safe and effective use, maintenance, and care of your Conentool Cordless Strimmer. Please read and understand all instructions thoroughly before operating the machine. This product is designed for private, light domestic use in small spaces and is not suitable for commercial applications or larger open areas.

For visual guidance on installation and use, please refer to the official video:

A detailed user manual is also available in PDF format. You can reference it at: Conentool Cordless Strimmer User Manual (PDF).

2. Safety Instructions

WARNING! Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

General Safety

• Never allow children, persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, or people unfamiliar with these instructions to use the machine.
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children.
• Keep the garden power tool out of reach of children.
• Store the instruction manual in a location accessible to all users and always include it when passing the tool to other users.
• Instruct inexperienced persons on the safe use of this garden power tool using this instruction manual.

Work Area Safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Battery Safety

• Do not place the battery in a concave or damaged place to avoid battery damage.
• When the battery power is less than 50%, it should be charged in time to avoid battery damage.
• Do not try to open the battery casing to avoid electric shock or other safety issues.

Personal Safety

• Stay alert, watch what you are doing, and use common sense when operating a power tool.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up, or carrying the tool.

Power Tool Use and Care

• If the switch does not turn on or off, do not use the tool and have it serviced.
• Disconnect the power source and remove the battery pack from the power tool before making any adjustments, changing accessories, or storing the power tool.
• Store idle power tools out of the reach of children and do not allow anyone unfamiliar with the power tool or these instructions to operate the power tool.
• Maintain the power tool and accessories. If damaged, repair the power tool before use.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to stick and are easier to control.

3. Product Components

The Conentool Cordless Strimmer comes with the following components:

Figure 1: Overview of the Conentool Cordless Strimmer and its included accessories.

Figure 2: Detailed view of all items included in the product package.

Product List:

• 1 x Lawn Mower Machine (main unit)
• 1 x Tooth Saw Blade
• 2 x Metal Blades
• 10 x PVC Plastic Blades
• 2 x Wire Haying Ropes
• 1 x Carrying Handle
• 1 x Anti-bump Bracket
• 1 x Safety Glasses
• 1 x Gloves
• 1 x Spanner (Allen wrench)
• 1 x Protective Board
• 1 x Charger
• 2 x Batteries (2.0Ah)
• 1 x Power Cord

Note: For model LG-D1003, an Auxiliary Wheel is also included.

4. Setup and Installation

Follow these steps to assemble your Conentool Cordless Strimmer:

4.1. Adjusting Connecting Rods

1. Align the concave and convex interfaces at both ends of the connecting rods.
2. Tightly fit them together.
3. Push the fixing device to the connection point and rotate it to secure the connection.

4.2. Installing the Handle

1. Position the handle in the proper position on the main shaft.
2. Place it vertically on the rod.
3. Align the retaining nut with the interface and rotate to secure it firmly.

Figure 3: The adjustable handle can be positioned for user comfort.

4.3. Installing the Grass Cover

1. Align the grass cover with the main unit.
2. Fix the dimpled joints into place.
3. Rotate to secure the grass cover.

4.4. Installing the Crash Bar (Anti-Collision Wire)

1. Align both ends of the crash bar (anti-collision wire) with the designated interfaces on the strimmer head.
2. Clamp it into place.

Figure 4: The anti-collision bar protects the cutting head. Be cautious of hard objects.

4.5. Blade Installation (Important Safety Notes)

Before installing any blade, ensure the battery is NOT installed and the power switch is in the OFF position to avoid injury. The saw blade is sharp; handle with extreme caution.

Figure 5: Visual guide for installing the circular saw blade.

Option 1: Saw Blade / Metal Blade / Plastic Blade Installation

1. Place the metal cover onto the spindle.
2. Position the desired blade (Saw, Metal, or Plastic) onto the spindle, ensuring it is in the correct cutting direction. Incorrect direction will make cutting difficult.
3. Add any necessary gaskets.
4. Secure with the nut and tighten using the provided spanner/Allen wrench.

Option 2: Wire Haying Rope Installation

1. Place the metal cover onto the spindle.
2. Insert the wire haying rope into the designated slots.
3. Secure with the nut and tighten using the provided spanner/Allen wrench.

4.6. Battery Installation

1. Align the battery with the recessed port on the main unit.
2. Insert the battery firmly until it clicks into place.

Figure 6: The 21V 2000mAh lithium battery provides up to 60 minutes of operation.

Your strimmer is now assembled and ready for use.

5. Operating Instructions

5.1. Starting the Strimmer

To start the strimmer, press and hold the rectangular start button located inside the handle and simultaneously press the round safety switch on the side of the handle.

5.2. Adjusting Length and Angle

• Telescopic Length Adjustment: Press and hold the control button on the shaft and adjust the length by pushing or pulling the shaft back and forth. The strimmer can be adjusted from 90cm to 125cm.
• Head Rotation Angle Adjustment: Press and hold the side button near the strimmer head to adjust the connection angle between the engine and the handle. This allows for adaptation to various terrains and user preferences. The head rotation angle is 45°.

Figure 7: Telescopic length adjustment for comfortable use.

5.3. Blade Selection and Application

The Conentool Cordless Strimmer is versatile, offering different blades for various cutting tasks:

Figure 8: Different blade types and their recommended uses.

• Plastic Blades: Ideal for soft weeds, lawn edges, and trimming near walls or fences.
• Metal Blades: Suitable for medium-hard weeds, dry grass, and light shrubs.
• Saw Disc (Circular Saw Blades): Best for rough vegetation such as shrubs, vines, saplings, and dense weeds.
• Steel Wire Rope: Used for trimming edges, lawn mowing, and narrow corners, including edges of masonry.

Figure 9: Application scenarios for different blade types.

The product is not intended for cutting unusually thick grass or vegetation, wet grass, or for shredding leaves.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your strimmer.

• Cleaning: After each use, clean the cutting head and blades to remove grass, dirt, and debris. Ensure the machine is off and the battery is removed before cleaning.
• Blade Care: Keep all cutting tools sharp and clean. Dull blades can reduce efficiency and put strain on the motor. Replace damaged or worn blades promptly.
• Battery Storage: If the battery is not used for a long time, store it in a dry place, away from moisture. Charge the battery every 2 months to maintain its health.
• General Inspection: Periodically check all nuts, bolts, and fasteners for tightness. Ensure all safety guards are securely in place.

7. Troubleshooting

Suspected malfunctions are often due to causes that users can fix themselves. Check the product using this section; in most cases, problems can be solved quickly.

Problem: Product does not start

• Solution 1: Fully charge the battery. The charger light should turn green when fully charged.
• Solution 2: If the machine cannot start during use, check if the motor is blocked by grass. If so, clean the grass and try starting again.
• Solution 3: When starting, ensure you press the start switch and the safety switch at the same time.

Problem: Battery not charging

• Solution 1: Upon receiving the product, fully charge the battery until the charger turns green.
• Solution 2: If not used for a long time, store the battery in a dry place, avoid moisture, and charge it every 2 months.

Problem: Accessories are easily broken

• Solution 1 (Plastic Blades): When using plastic blades to mow grass, avoid touching hard objects or cutting branches thicker than 10mm, as this can easily break the blades.
• Solution 2 (All Blades): When mowing with any blade type, avoid touching stones and hard objects, as this can damage the blades.

8. Specifications

9. User Tips

Based on common user experiences and questions, here are some helpful tips:

• Blade Longevity: To extend the life of your plastic blades, avoid contact with very hard objects like rocks or thick branches (over 10mm). For tougher tasks, switch to metal blades or the saw disc.
• Edge Trimming: The steel wire rope is excellent for precise trimming along edges and in narrow spaces, but be mindful of masonry to prevent wear.
• Battery Management: Always ensure your battery is fully charged before starting a task. If storing the strimmer for an extended period, remember to charge the battery every two months to prevent degradation.
• Motor Protection: If the strimmer stops unexpectedly, check the motor for grass blockage and clear it before restarting. This prevents overheating and damage.

10. Contact and Support

For further assistance or inquiries, please contact:

Manufacturer/Exporter:

SHEN ZHEN XIN SHENG SHANG TECHNOLOGY CO.,LTD.
Production Site: Room 303, Building 9, No. 54-6, Guanlan Avenue, Xinhe Community, Fucheng Street, Longhua District, Shenzhen City, Guangdong Province, China
Zip Code: 518000
Phone: +86 13048907387
E-mail: support@conentool.com
Official Website: www.conentool.com
Facebook ID: @DIY.Studio.CT

EU Representative (EC REP):

Company: Apex CE Specialists GmbH
Address: Grafenberger Allee 277, 40237 Düsseldorf, DE
Contact: Wells Yan
Tel: +4921312066043
E-mail: Info@apex-ce.de