Important Notice
This modem was locked on Russia by Quectel. Buyers from Russia should not purchase this product.
1. Introduction
The Quectel LC29H is a series of high-precision, dual-band multi-constellation GNSS (Global Navigation Satellite System) modules. Designed for applications requiring accurate and reliable positioning, these core boards support various satellite systems including GPS, GLONASS, Galileo, BeiDou, QZSS, and IRNSS across L1 and L5 frequency bands. The LC29H series offers advanced features such as RTK (Real-Time Kinematic) for sub-meter accuracy, integrated LNA for high sensitivity, and AGNSS for faster positioning.
This manual provides essential information for the proper setup, operation, and maintenance of your LC29H module.
2. Safety Precautions
Please read and follow these safety guidelines to prevent damage to the module or injury to yourself:
- **Electrostatic Discharge (ESD) Protection:** Handle the module with care, using appropriate ESD protection measures (e.g., anti-static wrist strap, grounded work surface) to prevent damage to sensitive electronic components.
- **Power Supply:** Ensure the power supply voltage is within the specified range (3.1V to 3.6V). Incorrect voltage can permanently damage the module.
- **Wiring:** Double-check all wiring connections before applying power to avoid short circuits or incorrect polarity.
- **Operating Environment:** Operate the module within the specified environmental conditions (temperature, humidity) to ensure optimal performance and longevity.
- **Antenna Connection:** Connect the antenna securely before powering on the module.
3. Package Contents
Upon receiving your Quectel LC29H Core Board, please verify that all items are included:
- 1x LC29H GNSS Module (Specific variant: EA, DA, BA, or AA)
- 1x Antenna (Optional: With antenna 1, With antenna 2, or No antenna, depending on your selection)
4. Setup and Installation
Follow these steps to set up your LC29H module:
- **Power Connection:** Connect the 5V and GND pins to your power supply. Ensure the voltage is stable and within the 3.1V-3.6V range.
- **Data Interface:** Connect the TX and RX pins to your host microcontroller or development board for serial communication. The default UART baud rate is 9600bps.
- **Antenna Connection:**
- If your module has an SMA connector, connect your external GNSS antenna to the SMA port.
- If your module has an IPEX1 connector, connect a compatible IPEX antenna to the IPEX1 port.
- **PPS Output:** The PPS (Pulse Per Second) pin provides a precise timing signal, which can be connected to your host system if timing synchronization is required.
- **Power On:** Once all connections are secure, apply power to the module. The POWER indicator LED should illuminate.
For detailed wiring diagrams and advanced integration, please refer to the official Quectel LC29H Series documentation, which can be found at the seller's product page or Quectel's website.
5. Operating Instructions
The LC29H module operates by receiving signals from multiple GNSS constellations to calculate its position, velocity, and time (PVT) information. This data is typically output via the UART interface in standard NMEA 0183 or RTCM 3.3 formats.
- **Initial Power-Up:** Upon power-up, the module will automatically begin searching for satellite signals. Ensure the antenna has a clear view of the sky for optimal performance.
- **Data Reception:** Your host system can read the NMEA/RTCM messages from the UART TX pin. These messages contain the raw and processed GNSS data.
- **RTK Operation (if applicable):** For RTK functionality, the module requires correction data from a base station. This data is typically fed into the module via the UART RX pin. Refer to Quectel's RTK application notes for detailed configuration.
- **AGNSS/EPO:** The module supports Assisted GNSS (AGNSS) and Extended Prediction Orbit (EPO) for faster Time-To-First-Fix (TTFF). These features may require external data injection or internet connectivity depending on the implementation.
- **Firmware Updates:** Firmware updates can be performed via the UART interface. Consult Quectel's documentation for the specific procedure and tools.
6. Specifications
The Quectel LC29H series offers robust performance for various positioning applications. Below are the key specifications:
6.1. Key Features
- Dual-band multi-constellation GNSS receiver
- Supports L1/L5 bands for GPS, GLONASS, Galileo, BeiDou, QZSS, IRNSS
- RTK (optionally providing sub-meter accuracy with fast convergence)
- Integrated LNA for high sensitivity
- Integrated AGNSS for faster positioning
- Low power consumption
- 12nm technology
- Supports dead reckoning (optional)
- Supports multi-tone active interference cancellation
- Supports multi-GNSS via single RF front-end
- Supports firmware upgrade via UART
6.2. GNSS Features
- **Supported GNSS**: GPS, GLONASS, Galileo, BeiDou, QZSS, IRNSS
- **L1 Band**: GPS L1 C/A, GLONASS L1OF, Galileo E1, BeiDou B1I/B1C, QZSS L1 C/A, IRNSS L5
- **L5 Band**: GPS L5, Galileo E5a, BeiDou B2a, QZSS L5
- **Channels**: 135 acquisition, 47 tracking
- **SBAS**: WAAS, EGNOS, MSAS, GAGAN
- **AGNSS**: Supported
- **EPO**: Supported
- **EASY**: Supported
6.3. Performance Data
- **Horizontal Position Accuracy**: Autonomous: 1.5m CEP; RTK: 0.01m + 1ppm CEP
- **Velocity Accuracy**: 0.02m/s
- **Acceleration Accuracy**: 0.1m/s²
- **Timing Accuracy**: 20ns
- **Cold Start TTFF**: Autonomous: 28s; AGNSS: 2s
- **Warm Start TTFF**: Autonomous: 25s; AGNSS: 2s
- **Hot Start TTFF**: Autonomous: 1s; AGNSS: 1s
- **Reacquisition TTFF**: 1s
- **Sensitivity**: Acquisition: -148dBm; Tracking: -167dBm; Reacquisition: -160dBm
- **Dynamic Performance**: Max Altitude: 18000m; Max Velocity: 515m/s; Max Acceleration: 4g
- **Data Update Rate**: 1Hz (default), up to 10Hz
6.4. Interfaces
- **UART**: Default: 9600bps, up to 4Mbps
- **I2C**: Supported
- **SPI**: Supported
- **PPS**: Supported
- **Protocols**: NMEA 0183/RTCM 3.3
- **Antenna Type**: Active/Passive
6.5. Electrical Data
- **Supply Voltage**: 3.1V to 3.6V (typical 3.3V)
- **Power Consumption**: Acquisition: 40mA; Tracking: 30mA; Sleep: 1.5mA; Backup: 10uA
6.6. Environmental Data
- **Operating Temperature**: -40°C to +85°C
- **Storage Temperature**: -40°C to +90°C
6.7. Physical Characteristics
- **Dimensions**: 16.0mm x 12.2mm x 2.4mm
- **Weight**: Approx. 0.9g
- **Package**: LCC
7. Troubleshooting
If you encounter issues with your LC29H module, consider the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No satellite signal / Poor positioning accuracy | Antenna not connected, obstructed view of sky, faulty antenna, interference. | Ensure antenna is securely connected and has a clear, unobstructed view of the sky. Try a different antenna. Check for nearby sources of electromagnetic interference. |
| No data output from UART | Incorrect wiring (TX/RX swapped), incorrect baud rate, module not powered. | Verify TX/RX connections. Ensure host system's baud rate matches module's (default 9600bps). Check power supply to the module. |
| Module not powering on | Incorrect power supply voltage, reversed polarity, faulty power connection. | Check power supply voltage (3.1V-3.6V). Verify correct polarity (5V to 5V, GND to GND). Inspect power connections for shorts or breaks. |
8. User Tips
- **Documentation Review:** Always refer to the latest official Quectel documentation for detailed technical specifications, AT commands, and application notes specific to your LC29H variant.
- **Antenna Quality:** The performance of your GNSS module is highly dependent on the quality and placement of your antenna. Invest in a good quality antenna and ensure it has a clear view of the sky.
- **Power Stability:** Provide a stable and clean power supply to the module to prevent unexpected behavior or signal degradation.
9. Warranty and Support
For warranty information, technical support, and further assistance, please contact the seller or refer to the official Quectel website. Keep your purchase records handy when seeking support.
You can also find additional resources and documentation, including the user manual in PDF format, by visiting the product page or the manufacturer's support portal.
Official PDF User Manual: Quectel LC29H Series User Manual (PDF)