HITBOX HBC45II

Contents

HITBOX Plasma Cutter HBC45II User Manual

Low Frequency Contactless Cutting 110/220V Digital Screen Display 2T/4T With Grid Cutting Function

1. Safety Information

Welding and plasma cutting are inherently dangerous operations that can cause serious injury or even death if proper precautions are not taken. Always prioritize safety for yourself and others in the work area.

General Safety Precautions

  • Professional Training: Only qualified personnel with a valid metal welding license (OFC) should operate this machine.
  • Power Disconnection: Always turn off the power and unplug the machine before performing any maintenance, repair, or connecting/disconnecting output cables. Allow at least 5 minutes for power capacitors to discharge.
  • Grounding: Install the grounding device according to application criteria. Ensure the ground clamp is firmly attached to clean metal of the workpiece.
  • Work Area: Keep the work area well-ventilated to avoid inhaling fumes and gas. Ensure the workplace is safe and free of combustible materials.
  • Personal Protective Equipment (PPE): Wear suitable welding masks and protective clothing (flame-resistant material) to protect eyes and body from arc radiation, sparks, and hot parts. Use masks or screens to protect onlookers.
  • Avoid Contact: Never touch electrically live parts with bare skin or wet gloves/clothing. Insulate yourself from workpieces. Do not touch hot parts with bare hands.
  • Cylinder Safety: Keep gas cylinders upright and chained to a support. Keep them away from physical damage, heat, sparks, flame, and live electrical circuits. Never allow the torch or welding electrode to touch the cylinder.
  • Moving Parts: Keep away from moving parts such as the fan. All doors, panels, covers, and safety devices must be closed during operation.
  • Equipment Malfunctions: If you encounter any difficulties, consult this manual. If the problem persists, contact the service center for professional help.
  • Safe Torch Use: Parts of the machine, such as the end of the filler wire and welding torch, become burning hot. The wire is sharp and moves quickly. Never carry the machine on your shoulder; use the shoulder strap for carrying only.
  • Chemicals: Do not operate the tool under the influence of alcohol or drugs.

2. Product Overview

The HITBOX HBC45II is a compact and portable plasma cutter designed for efficient and precise metal cutting. It features a low-frequency non-contact pilot arc start, digital display, and 2T/4T cutting modes, making it suitable for various applications.

Key Features:

  • Non-Contact Low Frequency Pilot Arc: Ensures stable, no-stick arc for superior cuts without needing to touch the metal plate.
  • Digital Screen Display: Provides all cutting data for monitoring device status and timely adjustments.
  • 2T/4T Function: Supports semi-automatic (2T) and automatic (4T) cutting control for continuous cutting, reducing fatigue and boosting productivity.
  • Grid Cutting Function: Allows cutting with continuous arc intervals, ideal for mesh and perforated materials.
  • Versatile Cutting: Ideal for carbon steel, iron, galvanized sheet, stainless steel, and other conductive metals.

Package Contents:

  • HBC45II Plasma Cutter * 1
  • Earth Clamp * 1
  • Hose clamp * 2
  • Nozzle * 2
  • Electrode * 2
  • Instruction manual * 1
  • 40A XS45 cutting gun * 1
  • Filter AFR-2000 gas meter * 1
  • PVC mesh tube 2M * 1
Diagram showing all components included in the HBC45II package, including the plasma cutter, cutting gun, ground clamp, hose, pressure regulator, and consumables.
Figure 2.1: Package Contents

Front Panel Controls:

Front panel of the HBC45II plasma cutter with labels for Current Display, Cutting Status Indication, Gun Nozzle Installation Tips, 2T/4T Status, Mesh Cutting Status, Fan Status, Abnormal Status, 110V/220V Status, Current Adjustment Knob, Mode Selector Button.
Figure 2.2: Front Panel Display and Controls
  1. Current Display
  2. Cutting Status Indication
  3. Tips For Abnormal Gun Nozzle Installation
  4. 2T/4T Status
  5. Mesh Cutting Status
  6. Fan Status
  7. Abnormal Status
  8. 110V/220V Status
  9. Current Adjustment Knob
  10. Mode Selector Button
  11. Cutting Gun Interface
  12. Ground Clamp Interface

Rear Panel Connections:

Rear panel of the HBC45II plasma cutter with labels for Power cable, Cylinder gas hose, Power switch, Location of screws for gas meter, Machine inlet pipe connection, air meter, Machine inlet pipe.
Figure 2.3: Rear Panel Connections
  1. Power cable
  2. Cylinder gas hose
  3. Power switch
  4. Location of screws for gas meter
  5. Machine inlet pipe connection
  6. Air meter
  7. Machine inlet pipe

3. Setup Instructions

3.1. Choosing a Suitable Location

  • Place the machine in an area with open space to ensure unrestricted air circulation for cooling.
  • Avoid locations with excessive dirt and dust to prevent overheating and automatic shutdown.
  • Ensure the machine is placed on a secure, level surface to prevent tipping.
  • Keep the machine dry and away from wet ground or puddles. Do not operate in rain.

3.2. Air/Gas Connection

The HBC45II requires an external air compressor for operation. The machine is equipped with a US Industry 1/4" NPT Male Coupler Quick Connector for easy connection to your air compressor.

  1. Connect the pressure regulator to the machine's air inlet.
  2. Attach the hose from your external air compressor to the pressure regulator. Secure with a hose clamp.
  3. Ensure the pressure regulator is set to 50-60 pascals for regular use.
Video 3.1: Demonstrates the setup process, including connecting the pressure regulator and gas hose, and setting the air pressure.
Diagram showing the machine wiring for gas input, connecting the gas hose to the pressure regulator and then to the machine's air inlet.
Figure 3.1: Machine Wiring for Gas Input

3.3. Machine Wiring Diagram

Diagram showing the machine wiring, including the ground clamp connection and the gas input connection.
Figure 3.2: Overall Machine Wiring Diagram

4. Operating Instructions

4.1. Power On and Initial Checks

  1. Ensure all connections (power, ground clamp, gas hose) are secure.
  2. Turn the power switch to 'ON'.
  3. Check the digital display for current settings and status indicators.

4.2. Setting Cutting Parameters

  • Use the Current Adjustment Knob to set the desired cutting amperage.
  • Use the Mode Selector Button to switch between 2T (Semi-Automatic) and 4T (Automatic) cutting modes, or to activate the GRID cutting function.

4.3. Cutting Modes

The HBC45II offers flexible cutting modes to suit different tasks:

  • 2T (Semi-Automatic Cutting Control): Press and hold the torch trigger to maintain the arc. Release to stop.
  • 4T (Automatic Cutting Control): Press the torch trigger once to start the arc, and press again to stop. This mode is ideal for longer cuts to reduce operator fatigue.
  • GRID Cutting Function: This mode provides continuous arc intervals, which is beneficial when cutting mesh or perforated materials, ensuring a stable arc even when the torch passes over gaps.
Comparison of 2T and 4T cutting functions, showing how the torch trigger is used for semi-automatic and automatic control.
Figure 4.1: 2T vs 4T Cutting Function
Demonstration of grid cutting function with continuous arc intervals on a metal mesh.
Figure 4.2: Grid Cutting Function

4.4. Non-Contact Arc Start

The HBC45II features a non-contact pilot arc start. To begin cutting:

  1. Press the torch switch to initiate the arc.
  2. Align the torch with the metal to be cut. The arc will transfer to the workpiece without direct contact.
Image showing the non-contact pilot arc in action, with the torch held slightly above the metal surface.
Figure 4.3: Non-Contact Pilot Arc

5. Maintenance

Routine maintenance is crucial for preventing metal powder accumulation and ensuring the longevity and reliable operation of your plasma cutter.

5.1. Each Use

  • Torch Inspection: Check the Torch, Tip/Nozzle, Electrode, Swirl Ring, and Shield Cup for wear, cracks, or exposed wires. Replace or repair as needed.
  • Electrode Condition: Ensure the face of the electrode is not recessed more than 1/8". Replace if worn beyond this point.
  • Shield Cup: Verify the Shield Cup fits easily; if not, check the threads.

5.2. Weekly Maintenance

  • Fan Operation: Check for proper fan operation.
  • Cleaning: Blow or vacuum dust and dirt out of the entire machine and the air filter.

5.3. Periodic Controls on the Power Source

  • Clean the power source inside using low-pressure compressed air.
  • Check all electrical connections and cables.
  • Always use gloves in compliance with safety standards during maintenance.

6. Troubleshooting Plasma Cutting

Refer to the table below for common problems, their causes, and recommended actions.

Problem (Symptoms)Problem CauseRecommended Action
Torch does not work
  • Power switch off
  • Air supply is compromised
  • Ground clamp & cable is not attached
  • Turn power switch “ON”
  • Check air supply
  • Attach the ground clamp & cable securely to work-piece or steel table
Sparks shoot upward instead of downward through the material
  • Plasma cutting torch is not piercing the material
  • Torch may be too far away from stock
  • Material may not be grounded properly
  • Travel speed is too fast
  • Increase current
  • Decrease the distance of your torch to stock
  • Check connections for proper grounding
  • Reduce speed
Dross build-up on parts of cuts
  • Tool and material build up heat
  • Cutting speed is too slow or current is too high
  • Torch parts are worn
  • Allow material to cool down and then continue to cut
  • Increase speed or reduce current until dross is reduced to minimum
  • Inspect and repair/replace worn parts
Insufficient penetration
  • Torch is tilted too much
  • Metal is too thick
  • Torch parts are worn
  • Make tilt adjustments
  • Several passes may be necessary
  • Inspect and repair/replace worn parts
Consumables wear out quickly
  • Exceeding unit capability
  • Improperly assembled torch
  • Inadequate air supply: pressure is too low
  • Faulty air compressor
  • Material is too thick. Increase angle to prevent blowing back into torch tip
  • Assemble torch correctly referring to Installation
  • Check air filter, increase air pressure
  • Check air compressor operation

Error Codes:

Error CodeResolvent
ERROR 1: OvercurrentCheck if the air pressure of the machine is too low or not connected to the air, restart the machine.
ERROR 2: OverheatWait for the machine to cool naturally and it's ready to use.
ERROR 3: Gun nozzle not installed or no gasCheck nozzle electrode installation.
ERROR 4: Thermocouple abnormal, sensor not detectedContact the manufacturer for technical support.

7. Specifications

AttributeValue
Model NumberHBC45II
OriginMainland China
Dimensions425*255*305mm (Product: 33*12*23 cm)
Brand NameHITBOX
Weight6.55KG (Product: 6.6kg)
CertificationCE
UseCutting Machine
Input Voltage110V~220V±10%, 1-PH, 50/60Hz
Output Current12~35A
Output Voltage100V
Gas SupplyClean, dry, oil-free air
Recommended Pressure/Flow Rate0.6~0.75Mpa, 3.0scfm @70psi
Pilot Arc Start ModeNon-HF Plasma Cutting
Maximum Severance Cutting Thickness15mm (3/5inch)
Ideal Cutting Thickness8-15mm
Mild Steel (Normal Cut)10mm (2/5inch)
Stainless Steel (Normal Cut)35A
Aluminum (Normal Cut)35A
Rated Duty Cycle35% 35A (60% duty cycle is percentage of 10 minutes that unit can weld at rated load without overheating)
Power Cable6' (1.8m)
Housing Protection GradeIP21
Display TypeDigital LED Panel
Switch TypeButton
ColorOrange

8. User Tips

  • External Air Compressor: This unit does not have a built-in air compressor. Ensure you have an external air compressor available and properly connected for operation.
  • Nozzle Wear: The nozzles are consumables and may show signs of use even on new machines due to factory testing. This is normal. Regularly inspect and replace worn nozzles for optimal cutting performance.
  • Optimal Performance: For best results, ensure your air pressure is consistently within the recommended 50-60 pascals.

9. Warranty & Support

The HITBOX HBC45II Plasma Cutter comes with a one-year warranty.

Support Resources:

  • Official Website: For additional information, product registration, and support, please visit www.hitboxweld.com.
  • User Manual (PDF): A detailed user manual in PDF format is available for download. You can view it here.
  • Social Media: Connect with HITBOX and find support on various platforms:
Facebook iconYouTube iconInstagram iconLINE icon

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.