1. Introduction
The LILYGO T-SIM7080G-S3 is a versatile development board integrating the ESP32-S3 microcontroller with a SIM7080G cellular module. This board offers comprehensive connectivity options including Wi-Fi, Bluetooth 5.0, Cat-M, NB-IoT, and GPS/GNSS capabilities, making it ideal for a wide range of Internet of Things (IoT) applications requiring both local and wide-area network communication.

2. Package Contents
Upon receiving your LILYGO T-SIM7080G-S3 development board, please verify that all the following items are included:
- 1 x T-SIM7080G-S3 Development Board
- 1 x LTE Antenna
- 1 x GPS Antenna
- 1 x Power Cable (2-pin JST-PH connector)
- 2 x Pin Headers

3. Board Layout and Pinout
Familiarize yourself with the board's components and pin assignments before proceeding with setup.
3.1. Component Overview
The board features an ESP32-S3 module for Wi-Fi and Bluetooth, a SIM7080G module for cellular and GPS, USB-C for power and data, a Micro USB for SIM7080G update UART, a TF card slot, a SIM card slot, and a battery holder for 18650 batteries.


3.2. Pinout Diagram
The pinout diagram illustrates the assignment of GPIOs, power pins, and other interfaces. Refer to this diagram for connecting external components and sensors.

4. Setup Instructions
Follow these steps to prepare your T-SIM7080G-S3 board for operation.
4.1. Power Supply
- The board operates on a supply voltage of 3.4V to 4.2V.
- You can power the board via the USB-C port or by inserting an 18650 Li-ion battery into the battery holder on the back of the board. Ensure correct polarity when inserting the battery.
- The included 2-pin power cable can be used for external power input if preferred.
4.2. SIM Card Installation
- The board supports 1.8V/3.0V SIM cards.
- Locate the SIM card slot on the board. Gently insert your activated Nano-SIM card into the slot until it clicks into place. Ensure the card is oriented correctly as indicated on the board.
4.3. Antenna Connections
- Connect the provided LTE antenna to the 'NB-IoT Antenna' U.FL connector.
- Connect the provided GPS antenna to the 'GPS Antenna' U.FL connector.
- Ensure connections are secure but do not apply excessive force.
4.4. TF Card Installation
- If your application requires external storage, insert a TF (MicroSD) card into the designated slot.
4.5. Initial Power On and Switches
- After connecting power and necessary peripherals, slide the 'ON/OFF' switch to the 'ON' position.
- The board features several switches for control:
- 1: Reset: Resets the ESP32-S3 module.
- 2: Boot: Puts the ESP32-S3 into bootloader mode for flashing firmware.
- 3: PWR: Controls the main power to the board.
- 4: SIM-BOOT: Specific to the SIM7080G module's boot mode.
- For initial programming, you may need to hold the 'Boot' button while connecting USB or during the flashing process, depending on your development environment.
4.6. Driver Installation
When connecting the board to a computer via USB-C for the first time, you may need to install appropriate USB drivers. Drivers are typically available for Microsoft Windows 7/8/10, Linux, and Android operating systems.
5. Operating Instructions
The T-SIM7080G-S3 board can be programmed using various development environments.
5.1. Development Environment
- ESP32-S3 (Wi-Fi, Bluetooth): Program the ESP32-S3 using the Arduino IDE with ESP32 board support or Espressif's ESP-IDF framework.
- SIM7080G (Cat-M, NB-IoT, GPS): Interact with the SIM7080G module via AT commands sent from the ESP32-S3. Libraries are available for simplified communication.
5.2. Cellular Communication (Cat-M/NB-IoT)
To utilize Cat-M or NB-IoT, ensure your SIM card is provisioned for these services. Use AT commands or a suitable library to initialize the SIM7080G module, connect to the cellular network, and send/receive data. Supported protocols include TCP/IP, IPV4/IPV6/DNS, Multi-PDP, FTP/FTPS/HTTP/HTTPS.
5.3. GPS/GNSS Functionality
The SIM7080G module supports GPS, GLONASS, BD (BeiDou), and Galileo. After connecting the GPS antenna, use AT commands to query location data. Ensure the board has a clear view of the sky for optimal satellite reception.
5.4. Wi-Fi and Bluetooth
The ESP32-S3 provides standard Wi-Fi (IEEE 802.11 b/g/n) and Bluetooth LE (Bluetooth 5, Bluetooth mesh) connectivity. These can be programmed using standard ESP32 development practices.
6. Maintenance
- Handling: Handle the board with care to avoid damaging components. Avoid static discharge.
- Cleaning: Use a soft, dry cloth to clean the board. Do not use liquids or abrasive cleaners.
- Storage: Store the board in a dry, anti-static environment when not in use.
- Battery Care: If using an 18650 battery, ensure it is of good quality and charged appropriately. Do not overcharge or deep discharge.
7. Troubleshooting
- Board not powering on: Check power connections, battery polarity, and ensure the 'PWR' switch is in the 'ON' position. Verify the power supply voltage is within 3.4V-4.2V.
- Unable to upload code: Ensure correct USB-C cable is used (data capable), drivers are installed, and the board is in the correct boot mode (often by holding the 'Boot' button during upload). Check your IDE's port selection.
- No cellular network connection: Verify SIM card is active and correctly inserted. Ensure the LTE antenna is connected. Check network coverage in your area.
- No GPS fix: Ensure the GPS antenna is connected and has a clear, unobstructed view of the sky. GPS acquisition can take several minutes.
- Wi-Fi/Bluetooth issues: Check your code for correct initialization and configuration. Ensure antennas are not obstructed.
8. Specifications
Detailed technical specifications for the LILYGO T-SIM7080G-S3 development board.
8.1. General Specifications
| Feature | Description |
|---|---|
| Product | T-SIM7080G-S3 |
| MCU | ESP32-S3 |
| CAT-M & NB-IoT Module | SIM7080G |
| SIM Card Support | Yes |
| TF Card Support | Yes |
| Board Dimensions (L x W x H) | 11 CM x 3.2 CM x 2 CM |
| Supply Voltage | 3.4V ~ 4.2V |
| SIM Card Voltage | 1.8V/3.0V |
| USB Driver Support | Microsoft Windows 7/8/10, Linux, Android |

8.2. ESP32-S3 Specifications
| Feature | Description |
|---|---|
| Clock Speed | 240MHz |
| Flash Memory | 16MB |
| PSRAM | 8MB |
| Wireless Connectivity | Wi-Fi: IEEE 802.11 b/g/n-compliant Bluetooth LE: Bluetooth 5, Bluetooth mesh |
| Peripheral Interfaces | I2C, SPI, UART, SDIO, I2S, CAN |
8.3. SIM7080G Specifications
| Feature | Description |
|---|---|
| Form Factor | 77 PIN |
| Region | Global |
| Frequency Bands (CAT-M) | B1/B2/B3/B4/B5/B8/B12/B13/B14/B18/B19/B20/B25/B26/B27/B28/B66/B85 |
| Frequency Bands (CAT-NB) | B1/B2/B3/B5/B8/B12/B13/B18/B19/B20/B25/B26/B28 |
| Data Transfer (CAT-M) | Uplink: 1119Kbps, Downlink: 589Kbps |
| Data Transfer (CAT-NB) | Uplink: 150Kbps, Downlink: 136Kbps |
| GNSS Support | GPS, GLONASS, BD (BeiDou), Galileo |
| Protocols | TCP/IP, IPV4/IPV6/DNS, Multi-PDP, FTP/FTPS/HTTP/HTTPS |
| Android RIL | Android 5.0/6.0/7.0/8.0/9.0 |
| Certifications | RoHS, REACH, JATE, Telec, Docomo, KDDI, Softbank, RCM, CE(RED), GCF, Deutsche Telekom, FCC, IC, PTCRB, AT&T, Verizon, T-Mobile, US Cellular |


9. User Tips
- Power Management: When running on battery, consider optimizing your code for low-power consumption, especially for NB-IoT applications.
- Antenna Placement: For best cellular and GPS performance, ensure antennas are placed away from other electronic components and have a clear line of sight.
- Development Resources: Refer to the official Espressif documentation for ESP32-S3 and SIMCOM documentation for SIM7080G for in-depth technical details and examples.
- Firmware Updates: Regularly check for firmware updates for both the ESP32-S3 and SIM7080G modules to ensure optimal performance and access to new features.
10. Warranty and Support
For technical support, documentation, and warranty information, please refer to the official LILYGO website or contact your vendor. Keep your purchase receipt for warranty claims.