NEEWER Z2 PRO

Contents

NEEWER Z2 PRO 2.4G TTL Round Head Flash Speedlite User Manual

Model: Z2 PRO

Brand: NEEWER

1. Introduction

Thank you for your purchase of a NEEWER product. This Z2PRO-C camera flash is designed for Canon EOS series cameras and is compatible with E-TTL II autoflash features. It simplifies your shoots by providing correct flash exposure even in complex environments with variable lighting levels.

This camera flash features:

  • Maximum flash power of 76Ws, 81 levels of dimming (1/1~1/256).
  • Upgraded quartz tube supports up to 100,000 flashes during its lifespan.
  • 3000mAh Li-polymer battery with an autonomy of 600 flashes at full power, 1.5 seconds fast recharge.
  • Supports E-TTL auto flash, which can be used as the master or slave unit of a wireless multi-lamp flash system, making shooting easier and faster.
  • LCD screen for an intuitive display and easy operation.
  • Built-in 2.4GHz wireless transmission, integrated transmitter and receiver with a large radius.
  • Supports manual frequency flash mode, HSS/second curtain sync /FEC and other E-TTL II functions.
  • Stable output, high speed continuous flash and color temperature with good even lighting.
  • Firmware will be upgraded as the camera is updated.

2. Precautions

  • Always keep this product dry.
  • Keep this product out of reach of children.
  • Do not disassemble or modify the product.
  • Do not subject to any form of physical shock. The product shouldn't be exposed to fire or an environment where the temperature exceeds 50 degrees.
  • Do not fire the flash directly into the eyes which could result in visual impairment.
  • Do not use the product near chemicals, flammable gases or other volatile substances which may cause fire or electromagnetic interference.
  • Do not use in the rain or in damp conditions.
  • Turn off the product immediately, if it appears to be operating abnormally, and try to troubleshoot the likely cause.
  • Failure to comply with the recommendations and warnings listed in the manual will invalidate the warranty.

3. Package Contents

The package includes the following items:

  • Flash unit ×1
  • Lithium Battery ×1
  • Mini stand ×1
  • USB power cord ×1
  • Protective Case ×1
  • Manual ×1
NEEWER Z2 PRO Flash Speedlite and included accessories
Figure 3.1: NEEWER Z2 PRO Flash Speedlite and included accessories.

4. Name of Components

4.1. Flash Body

Diagram of NEEWER Z2 PRO Flash Body components
Figure 4.1: Flash Body Components.
  1. Lithium Battery
  2. Battery Release Button
  3. Hot Shoe Base
  4. Flash Head
  5. Wireless Sensor
  6. Modeling Lamp
  7. Focus Assist Lamp

4.2. Control Panel

Diagram of NEEWER Z2 PRO Control Panel
Figure 4.2: Control Panel Layout.
  1. <TCM> One-touch Switching
  2. Type-C USB Upgrade Port (Note: Exclusively for firmware upgrades, not charging)
  3. Sync Jack
  4. <MODE> Mode Selection/Lock Button
  5. <Test Flash Button/Recycling Indicator
  6. Hot Shoe Fixing Button
  7. Display
  8. Function Button 1
  9. Function Button 2
  10. Function Button 3
  11. Function Button 4
  12. <Wireless Button
  13. <Modeling Lamp
  14. Power ON-OFF/Setting Button
  15. Adjustment Knob

4.3. LCD Panel

The LCD panel provides an intuitive display for various settings and modes.

NEEWER Z2 PRO Flash UI showing TTL mode
Figure 4.3: E-TTL Autoflash Display on LCD Panel.

5. Battery

5.1. Features

  • This flash unit uses a Li-ion polymer battery which boasts a long service life and can be charged/discharged up to 500 times.
  • Safe and reliable, the built-in circuit protects against overcharge, overdischarge, overcurrent, and short circuit.

5.2. Battery Caution

  • Do not short circuit.
  • Do not immerse the battery in water.
  • Keep the battery out of reach of children.
  • Do not exceed 24 hours of continuous charging.
  • Store the battery in a dry, cool and ventilated environment.
  • Do not place the battery near or in a fire.
  • Dead batteries should be disposed according to local regulations.
  • If the battery isn't to be used for some time, please ensure it is charged at least every 3 months.

5.3. Inserting and Removing the Battery

To insert the battery, slide the lithium battery into the battery compartment in the direction indicated by the battery until the fastener snaps into place.

To remove the battery, slide the button in the direction shown to remove the battery.

NEEWER Z2 PRO battery and USB Type C charging
Figure 5.1: High performance lithium battery and USB Type C charging.

5.4. Battery Level Indicator

Make sure the battery is securely inserted in the flash. Check the battery level indication on the LCD panel to see the remaining battery level.

Battery Level Indicator Indicates
4 bars Full
3 bars Medium
2 bars Low
1 bar Very low
Empty bar Low battery. Please charge as soon as possible.
Flashing Battery is about to run out. The flash will no longer work. Please recharge the battery as soon as possible (within 10 days); the battery can then be used or stored for a long period.

6. Power Management

Use the ON/OFF Power Switch to power the flash unit on or off. Please turn off the power if the flash won't be used for a long period.

When setting as a transmitter (TX) flash, the flash will turn the power off automatically after a certain period (approx. 90 seconds) of inactivity. Pressing the camera shutter halfway or pressing any flash button will wake up the flash unit. When setting as a receiver (RX) flash, it will enter sleep mode after a certain period (adjustable, 60 minutes by default) of idle use. Pressing any flash button will reactivate device.

To turn the flash on/off, press and hold the power button for 2 seconds.

7. Mounting and Unmounting the Flash

7.1. Mount the Camera Flash

Turn the locking ring to the left to fully insert the camera's hot shoe.

7.2. Secure the Camera Flash

Rotate the locking ring to the right until secure.

7.3. Unmount the Camera Flash

Press the button and rotate the hotshoe locking ring to the left to loosen.

NEEWER Z2 PRO Flash mounted on a Canon DSLR camera
Figure 7.1: NEEWER Z2 PRO Flash mounted on a Canon DSLR camera, showing quick lock & unlock and metal hot shoe.

8. Flash Modes

This flash has three flash modes: E-TTL, Manual (M), and Multi (Stroboscopic). Press the <MODE> Mode Selection Button to cycle through these modes on the LCD panel.

8.1. E-TTL Autoflash Mode

In E-TTL mode, the camera's metering system detects flash illumination reflected from the subject and automatically adjusts the flash output to balance the exposure of the subject and background. Flash Exposure Compensation (FEC), Flash Exposure Bracketing (FEB), High-Speed Sync (HSS), Second-Curtain Shutter Sync, Flash Exposure Lock (FEL), aperture preview shadow flash, and Canon camera menu access are supported.

FEC (Flash Exposure Compensation): Adjusts flash exposure compensation in 1/3-stop increments between ±3 stops. Useful for fine-tuning TTL system. To set, turn the Select Dial. To cancel, set to "0.0".

FEB (Flash Exposure Bracketing): Automatically changes flash output in 1/3rd stops from -3 to +3. Records three photos with different flash outputs (correct, underexposed, overexposed). Set camera drive mode to "single" and ensure flash is ready. FEB will be canceled after three photos.

FEL (Flash Exposure Lock): Locks the correct flash exposure setting for any part of the scene. With <ETTL> displayed, press the camera's <FEL> button (or <*> button if no FEL button). Aim the viewfinder center at the subject, press <FEL> button. A preflash will fire, and the flash output is memorized. "FEL" will show in the viewfinder for 0.5 seconds.

8.2. M (Manual) Flash Mode

In Manual mode, you can manually set the flash output from 1/1 to 1/256 in 1/3-stop increments. This allows for precise control over lighting.

S1/S2 Optical Slave Mode: In M mode, the S1 function can be used as a secondary flash with optical sensor. The S2 function ignores the preflash from a master flash.

8.3. Multi (Stroboscopic) Flash Mode

Stroboscopic flash fires a rapid series of flashes to capture multiple images of a moving subject in a single photograph. You can set the firing frequency (Hz), the number of flashes, and the flash output.

Calculating Shutter Speed: During stroboscopic flash, the shutter remains open until the firing stops. Use the formula: Number of Flashes / Flash Frequency = Shutter Speed.

Note: To avoid overheating, do not use stroboscopic flash more than 10 times in succession. Allow 15 minutes rest after 10 consecutive uses.

NEEWER Z2 PRO Flash showing continuous flashes
Figure 8.1: NEEWER Z2 PRO Flash showing continuous flashes (100 times single, 100,000 lifetime).

9. Wireless Flash Shooting (2.4G Transmission)

The Z2PRO-C features a built-in 2.4G wireless system, allowing it to function as a transmitter (TX) or receiver (RX) unit. It is compatible with the NEEWER QPRO-C TTL transmitters (not included) and Godox 2.4G X system (RX COMPAT menu). Note: Q and X systems cannot be used simultaneously; latest firmware is required for compatibility.

9.1. Wireless Settings

You can switch between normal flash and wireless flash. For normal flash, ensure wireless settings are "off".

Transmitter (TX) Unit Setting: Press the <Wireless> button and turn the adjustment knob to select TX. Press Setup to confirm. The screen will display <((p))> and <TX>.

Receiver (RX) Unit Setting: Press the <Wireless> button and turn the adjustment knob to select RX.

9.2. Turn off TX Unit Flash

When the Transmitter (TX) unit flash is OFF, only the Receiver (RX) unit will fire flashes.

9.3. Setting the Communication Channel

If there is more than one wireless flash system nearby, you can change the communication channel to prevent signal interference. Set the channel of the Transmitter unit and Receiver unit to the same values (01-32).

9.4. Wireless ID Settings

To prevent interference, set the ID (01-99, OFF) for the transmitter and receiver to the same values.

9.5. Scan for a Free, Unused Channel

To avoid issues of interference, use the scan function to find an unused channel. When setting to SCAN, a list of free channels will be displayed.

9.6. Built-in 2.4G Wireless Q and X Systems

This flash features a built-in 2.4G wireless system, and can be used as the master/slave unit. It is compatible with the NEEWER QPRO-C TTL transmitters (not included). In addition, it also supports Godox 2.4G X system (RX COMPAT menu) or as a slave using Xpro X3 X2 transmitters. Compatible with Sekonic L-858D light meter (RT-GX module).

NEEWER 2.4G Wireless Q System and compatibility diagram
Figure 9.1: NEEWER 2.4G Wireless Q System and compatibility with Godox X System & Sekonic L-858D Light Meter.

9.7. ETTL: Automatic Wireless Flash Photography

The transmitter (TX) unit and the receiver (RX) unit must have the same wireless ID, channel, and group before the flashes can be fired wirelessly.

Using Automatic Wireless Flash with a Single Receiver Unit: Position the camera and flashes as indicated in the manual. Check if the flash is ready (Transmitter flash ready indicator lit, AF-assist beam lighting area flashes at 1-second intervals). Check flash operation by pressing the Transmitter unit's Test Button.

9.8. M: Manual Wireless Flash Shooting

Allows setting different flash outputs for each RX unit (flash group). All parameters need to be set on the TX control unit.

9.9. Multi: Wireless Flash Shooting with Manual Flash

To set the <MULTI> strobe mode, in the main control screen mode, press the <MODE> mode selection button to display <MULTI>. Set the strobe flash setting in the main control screen mode.

10. Other Applications

10.1. TCM - One Key Switching E-TTL/M Mode

Utilize E-TTL auto mode for quick metering while retaining metering data, and seamlessly switch to manual mode for precise adjustments. Toggle the TCM button to 'M' for one-touch switching.

10.2. Sync Triggering

The Sync Cord Jack is a 2.5mm connector. Insert a trigger plug here and the flash will be fired in sync with the camera shutter.

10.3. Auto Focus Assist Beam

In low-brightness or low-contrast shooting situations, the flash's built-in autofocus assist lamp turns on to make autofocusing easier. When focusing is difficult, the red autofocus assist light comes on. To turn off, set "AF" to "OFF" in C.Fn.

Position Operating range
Center 0.6-10m / 2.0-32.8 feet
Periphery 0.6-5m / 2.0-16.4 feet

10.4. Bounce Flash

By pointing the flash head toward a wall or ceiling, the flash will bounce off the surface before illuminating the subject. This can soften shadows behind the subject for a more natural-looking shot. This is commonly known as a 'bounce flash'. The flash head swivels 330° and tilts -7° to 120°.

Diagram showing flexible flash head rotation and tilt
Figure 10.1: Flexible flash head rotation and tilt for bounce flash.
  • If the wall or ceiling is too far away, the bounced flash might be too weak and result in underexposure.
  • The wall or ceiling should be a plain, white color for high reflectance. If the bounce surface isn't white it will result in "off color" photos.

10.5. ZOOM: Set the Flash Coverage

The flash coverage can be set automatically or manually (28mm to 105mm). In auto zoom, the focal length changes with the camera's zoom lens. For manual zoom, short press function button 1 <ZM/Fn> and turn the Select Dial to change flash coverage.

10.6. Modeling Lamp

The Z2PRO-C has two 2W 3300K LED modeling lamps with 10 brightness levels (01-10). Short press the modeling lamp button <Modeling Lamp> to turn it on/off. Rotate the adjustment knob to set brightness.

10.7. Modeling Flash

If your camera has a depth-of-field preview button, pressing it activates a 1-second continuous flash, known as modeling flash. This helps you observe the effect of the light and shadow on your subject and evaluate the illumination balance.

Note: Avoid triggering the modeling flash more than 10 times in quick succession. Allow 10 minutes for cooling after 10 consecutive uses. Modeling flash is not supported on EOS 300 and B models.

11. C.Fn: Setting Custom Functions

The flash unit has various custom functions that can be set according to your preferences. Refer to the manual's C.Fn table for detailed settings.

12. Control Using the Camera's Menu Screen

Mount the flash directly on the Canon EOS camera to control the flash settings using the camera's menu screen. Refer to your camera's instructions for details.

The following flash functions can be set according to different flash modes:

  • Flash mode
  • Shutter sync
  • FEC
  • Flash firing
  • Clear Camera Flash settings

13. Protection Functions

13.1. Over-Temperature Protection

To prevent the flash head from deteriorating and overheating, it is recommended not to fire more than 100 continuous flashes in fast succession at 1/1 full power. After 100 continuous flashes, pause the use of the flash for at least 10 minutes.

If you fire more than 100 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated. The recycling time will be longer (over 10s). If this occurs, the use of the device should be paused for at least 10 minutes for the flash unit to operate as normal.

Number of flashes that will activate over-temperature protection:

Power Number of Flashes
1/1 100
1/2 150
1/4 300
1/8 300
1/16 1100
1/32
1/64 3500
1/128
1/256

13.2. Other Safety Functions

The system provides real-time protection to secure the device and your safety. The following lists prompts for your reference:

Prompts on LCD Panel Indicates
E1 A fault has developed with the flash's recycle system so that the flash cannot fire. Please restart the flash unit. If the problem still exists, please send this product to a maintenance center.
HOT The flash will disable when the temperature inside the unit is too high in which case you should stop using the flash for 10 minutes.

14. User Tips

  • For optimal battery longevity, fully charge the device before first use.
  • When using the wireless system, ensure both the transmitter and receiver units have the same wireless ID and channel to avoid interference.
  • If experiencing issues with wireless communication, try adjusting the channel (CH) setting or turning off other 2.4G devices nearby.
  • The TCM (TTL to Manual) switch is a quick way to transition between automatic and manual control, making it easier to fine-tune your lighting.

15. Troubleshooting

If you experience a problem with the device, please refer to this troubleshooting guide.

15.1. The Camera Flash Does Not Fire

  • Flash not securely attached: Attach the hot shoe base mount of the flash securely to the camera.
  • Dirty electrical contacts: Clean the electrical contacts of the camera flash and camera.
  • Flash not recycled: Wait until the flash is fully recycled and the flash ready indicator lights up.
  • Low battery: If the flash ready indicator does not light up after a long period, check battery power. If the battery is low (flashing icon), replace it immediately.

15.2. Auto Power Off

  • Transmitter (Master) auto power off: After 90 seconds of idle operation, auto power off activates. Press the shutter button halfway or any flash button to wake up.
  • Receiver (Slave) sleep mode: After 60 minutes (or 30 minutes) of idle operation, the flash unit enters sleep mode. Press any flash button to wake up.

15.3. Auto Zoom Does Not Work

  • Flash not securely attached: Attach the camera flash's mounting base to the camera.

15.4. The Flash Exposure is Underexposed or Overexposed

  • Highly reflective object: If there was a highly reflective object (e.g., glass window) in the picture, use FE lock (FEL).
  • High-speed sync: With high-speed sync, the effective flash range will be shorter. Make sure the subject is within the effective flash range displayed.
  • Manual Flash mode: Set the flash mode to ETTL or modify the flash output.

15.5. Photos Have Dark Corners or Only Parts of the Target Subject are Illuminated

  • Focal length exceeds flash coverage: Check the focal length that has been set. This flash unit has flash coverage between 28 and 105mm, which fits medium-format cameras.

15.6. 2.4G Wireless Flash Misfiring

  • Interference: Adjust the channel CH setting of the transmitter (CH+10 is recommended) to find a channel without interference, or turn off other 2.4G devices in close proximity.
  • Flash not fully recycled: Ensure the flash is fully recycled, the flash ready indicator is on, and the overheat protection feature hasn't been triggered. Lower the flash setting by changing to manual mode (M).
  • Low power: Check whether the flash detector and the receiving device are running low on power. Replace the batteries.

16. Technical Data

Attribute Specification
ModelZ2PRO-C
Compatible CamerasCanon EOS cameras (E-TTL II autoflash)
Power (1/1 output)76Ws
Flash Coverage28-105 mm (Auto zoom, Manual zoom, Swinging/tilting flash head: 0 to 330° horizontally and -7° to 120° vertically)
Flash Duration1/180 to 1/20000 seconds
Exposure control systemE-TTL II autoflash and manual flash
Flash exposure compensation (FEC)Manual. FEB: ±3 stops in 1/3 stop increments (Manual FEC and FEB can be combined.)
Flash exposure lock (FEL)Use <FEL> button or <*> button
Sync modeHigh-speed sync (up to 1/8000 seconds), first-curtain sync, and second-curtain sync
Multi flashAutonomy (up to 100 times, 199Hz)
Wireless flash functionTransmitter, Receiver, Off
Transmitter groupsA, B, C, D
Controllable Receiver groupsA, B, C, D, E (E group can be controlled by QPRO series flash trigger available on Neewer.com)
Transmission range (approx.)100m
Channels32 Groups: 01~32
ID01~99
Frequency Range2412.75MHz-2464.25MHz
Maximum radio-frequency power5.30dBm
Modeling FlashUsing the camera's depth-of-field preview button
Auto Focus Assist Beam Effective range (approx.)Center: 0.6~10m / Periphery: 0.6~5m
Power source7.2V/3000mAh Li-ion battery
Recycle timeApprox 1.5 seconds. Red LED indicator will light up when the flash is ready.
Number of flash in full powerApprox. 600
Energy-savingAuto Power off after approx. 90 seconds of idle operation. (60 minutes if set as Receiver)
Sync Triggering ModeHotshoe, 2.5mm sync line
Modeling Lamp Power2W
Color Temperature3300K±20K
Dimensions76*76*206 mm
Net weight without battery460g
Weight with battery580g
Operating Temperature0°C ~ 40°C

17. Compatible Cameras

The NEEWER Z2 PRO is compatible with the following Canon camera models:

R, R3, R5, M6, 6D, 7D, R6, 60D, 50D, 70D, 80D, 90D, 1DX, 450D, 500D, 550D, 600D, 650D, 850D, 1100D, 3000D, 750D/T6i, 1D Mark III, 5D Mark II, 5D Mark III, 5D Mark IV, R8, 6D Mark II, 760D/T6s, 800D/T7i, 7D Mark II, 77D/9000D, 1500D/2000D/T7, 200D II/250D/SL3, R5C, R7, R10.

Note: Not compatible with RP and R50.

18. Restore Factory Settings

To restore the flash to its factory settings:

  1. Press and hold both Function buttons 2 and 3 simultaneously.
  2. "RESET" will appear on the screen to indicate that the factory settings have been restored.

19. Firmware Upgrade

The firmware of this product can be upgraded through the USB Type-C port. The latest software announcements and instructions will be published on the official NEEWER website.

  • This product does not come with a USB cable for the firmware upgrade. Please purchase separately. Use only a USB Type-C cable.
  • Upgrading the firmware requires Neewer Firmware software support. Download and install "Neewer Firmware Update", then select the corresponding firmware file.
  • As the product is undergoing a firmware upgrade, please refer to the latest electronic version of the manual.

20. Support and Further Information

For more detailed information and visual guides, you can refer to the official user manual PDF available at: NEEWER Z2 PRO User Manual (PDF).

For any further assistance or warranty information, please contact NEEWER customer support.

21. Product Overview Video

Video: Demonstrates the NEEWER Z2 PRO flash speedlite in use, showing UI, mounting, and light diffusion.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.