1. Introduction
The HOBBYWING Seaking 70A PRO G2 Brushless Electronic Speed Controller (ESC) is a high-performance, waterproof ESC designed specifically for competitive RC boat models such as Mini ECO, Mini Mono, and Mini Hydro class boats. It features advanced programmable parameters, robust protection mechanisms, and a compact design to deliver optimal performance and reliability in demanding aquatic environments.

Figure 1: Overview of the HOBBYWING Seaking 70A PRO G2 Brushless ESC.
2. Safety Information
⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Always handle electronic components with care. Ensure proper insulation and connections to prevent short circuits. Disconnect the battery when not in use or during maintenance. Keep the ESC away from extreme temperatures and direct sunlight when not in operation.
3. Product Overview
The Seaking 70A PRO G2 ESC is engineered for high performance and durability. Key features include:
- Waterproof Design: IP55 rated with a nano waterproof layer coating on the circuit board and components for enhanced water resistance.
- High-Power BEC: Built-in BEC with adjustable output (6V/7.4V/8.4V) delivering up to 10A peak current (5A continuous) for efficient power to servos and receivers.
- Optimized Performance: Designed to maintain lower temperatures and extend runtime, even under full throttle conditions.
- Turbo Function: Supports turbo timing for rapid acceleration and swift overtaking maneuvers.
- Freewheeling Function: Improves efficiency, reduces ESC temperature, and enhances throttle response when enabled.
- Data Logging: Real-time data tracking (throttle, voltage, current, temperature, RPM) via an optional OTA Bluetooth module and smartphone app (5-meter range).
- Firmware Updatable: Supports firmware updates via HOBBYWING USB LINK software or HV LINK mobile app, requiring an LCD programming box or OTA module (sold separately).
- Detachable Water-Cooling Heatsink: Removable heatsink for adaptability to lower-power applications or size/weight-sensitive setups.
- Comprehensive Protection: Features low voltage protection, over-temperature protection, throttle signal loss protection, overload protection, and capacitor overheating protection.

Figure 2: Seaking 70A PRO G2 ESC designed for RC boat racing, shown installed in a boat.

Figure 3: Illustration of the nano waterproof layer protecting internal components of the ESC.

Figure 4: Details on the powerful built-in BEC and superior reliability with multiple protection features.
4. Specifications
| Feature | Detail |
|---|---|
| Product Name | Seaking PRO 70A G2 |
| Brushed/Brushless | Brushless |
| Sensored/Sensorless | Sensorless |
| Waterproof Rating | IP55 |
| Continuous/Peak Current | 70A/200A |
| Input Voltage | 2-4S Lipo |
| BEC Output | Switch mode 6V/7.4V/8.4V @5A (10A peak) |
| Output Connectors | 4.0mm Female plug |
| Dimensions (LxWxH) | 38.5 x 30 x 8.4 mm |
| Weight | 35g (Without water cooling pipe) |
| Applicable Boat Models | Mini Mono, Mini ECO, Mini Hydro competition |
4.1 Optimized Programmable Parameters
The Seaking 70A PRO G2 offers 14 adjustable settings for greater customization. Refer to the table below for available options:

Figure 5: Optimized Programmable Parameter Table.
| No. | Item | Options | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | Running Mode | Forward Only | Forward and Reverse | |||||||
| 2 | Max Reverse Force | 25% | 50% | 75% | 100% | |||||
| 3 | Lipo Cells | Auto | 2S | 3S | 4S | |||||
| 4 | Cutoff Voltage (LED Box/OTA) | Disabled | 2.8V/Cell | 2.9V/Cell | 3.0V/Cell | 3.1V/Cell | 3.2V/Cell | 3.3V/Cell | 3.4V/Cell | 3.5V/Cell |
| 5 | ESC Thermal Protection | Disabled | 105°C/221°F | 125°C/257°F | ||||||
| 6 | BEC Voltage (LED Box) | 6.0V | 7.4V | 8.4V | ||||||
| BEC Voltage (LCD Box/OTA) | 6.0-8.4V, Step: 0.1V, Default: 6.0V | |||||||||
| 7 | Motor Rotation | CCW | CW | |||||||
| 8 | Punch | Level 1 | Level 2 | Level 3 | Level 4 | Level 5 | Level 6 | Level 7 | Level 8 | Level 9 |
| 9 | Initial Throttle Force | 2% | 3% | 4% | 5% | 6% | 7% | 8% | 9% | 10% |
| 10 | PWM Drive Frequency | 8K | 10K | 12K | 14K | 16K | ||||
| 11 | Freewheeling | Disabled | Enabled | |||||||
| 12 | Timing | 0° | 3.75° | 7.50° | 11.25° | 15° | 18.75° | 22.5° | 26.25° | 30.0° |
| 13 | Turbo Timing | 0° | 3.75° | 7.50° | 11.25° | 15° | 18.75° | 22.5° | 26.25° | 30.0° |
| 14 | Turbo Increase Rate | 5°/0.1s | 10°/0.1s | 15°/0.1s | 20°/0.1s | 25°/0.1s | 30°/0.1s | Instant | ||
5. Setup
5.1 Physical Installation
- Mounting: Securely mount the ESC within your RC boat model. Ensure it is placed in a location that allows for adequate airflow, even with the water-cooling heatsink.
- Water Cooling: Connect the water cooling pipes to the heatsink. Ensure a clear path for water flow to and from the heatsink for optimal cooling. The heatsink is detachable for specific applications; ensure it is properly attached if water cooling is desired.

Figure 6: Detachable water-cooling heatsink for the ESC.
5.2 Wiring Connections
Connect the ESC to your motor, battery, and receiver as follows:
- Motor Connection: Connect the three output wires from the ESC to the three phase wires of your brushless motor. Ensure correct phasing for proper motor rotation (adjust if necessary via programming). The ESC uses 4.0mm female plugs for output.
- Battery Connection: Connect your 2-4S Lipo battery to the input wires of the ESC. Pay close attention to polarity (red to positive, black to negative).
- Receiver Connection: Plug the BEC cable from the ESC into the throttle channel of your RC receiver. The built-in BEC provides power to your receiver and servos.

Figure 7: Seaking PRO 70A G2 ESC showing wiring for motor, battery, and receiver.
6. Operating Instructions
6.1 Initial Power-Up and Calibration
Before first use, it is recommended to calibrate the ESC with your radio system's throttle range. Refer to the detailed HOBBYWING ESC calibration guide for your specific radio system.
6.2 Programming Parameters
The Seaking 70A PRO G2 ESC features 14 adjustable parameters. These can be configured using an optional HOBBYWING LED Program Box, LCD Program Box, or OTA Bluetooth Module connected to a smartphone app (HV LINK). Refer to the "Optimized Programmable Parameter" table in the Specifications section for available settings.
6.3 Turbo Function
The Turbo Function allows for dynamic timing adjustments to deliver maximum power for rapid acceleration and swift overtaking maneuvers. This feature can be configured via the programming options (Turbo Timing and Turbo Increase Rate).

Figure 8: The Turbo Function enhances acceleration for competitive racing.
6.4 Freewheeling Function
Enabling the Freewheeling Function can lead to a cooler running ESC, faster response, and better overall control. It allows the boat to decelerate faster when the throttle is released. This setting can be enabled or disabled through programming.

Figure 9: Visual comparison of Freewheeling Function effects and devices for firmware updates.
6.5 Data Logging
With the optional OTA Bluetooth module, you can track real-time data such as throttle position, voltage, current, temperature, and RPM via a smartphone app. Historical data is available in graph format for performance analysis. The Bluetooth range is approximately 5 meters.

Figure 10: Data Logging Function with OTA Bluetooth module and smartphone app.
6.6 Firmware Updates
To ensure you have the latest features and performance enhancements, firmware updates are supported. These updates can be performed using the HOBBYWING USB LINK software on a PC or the HV LINK mobile app with an LCD programming box or OTA module (sold separately).
7. Maintenance
- Cleaning: Although waterproof, it is recommended to rinse the ESC with fresh water after use in saltwater or dirty conditions. Ensure all connectors are dry before storage.
- Inspection: Regularly inspect all wires and connectors for signs of wear, corrosion, or damage.
- Heatsink: Ensure the water-cooling heatsink and pipes are free from blockages and debris to maintain optimal cooling efficiency.
- Storage: Store the ESC in a dry, cool place away from direct sunlight and extreme temperatures.
8. Troubleshooting
The Seaking 70A PRO G2 ESC is equipped with several protection features to prevent damage. Understanding these can help in troubleshooting:
- Low Voltage Protection: If the battery voltage drops below the set cutoff voltage, the ESC will reduce power or cut off to protect the battery. Check battery charge and condition.
- Over-Temperature Protection: If the ESC or motor temperature exceeds the set limit, the ESC will reduce power. Allow components to cool down. Ensure proper water cooling is functioning.
- Throttle Signal Loss Protection: If the ESC loses throttle signal from the receiver, it will stop the motor to prevent runaway. Check receiver and transmitter connections and battery levels.
- Overload Protection: If the motor draws excessive current due to an overload (e.g., propeller obstruction), the ESC will protect itself by reducing or cutting power. Inspect the propeller and drivetrain for obstructions.
- Capacitor Overheating Protection: This feature helps prevent damage to the ESC caused by capacitor failure due to overloading.

Figure 11: Capacitor Overheating Protection mechanism.
9. User Tips
- For optimal performance in competitive racing, experiment with the programmable parameters such as "Punch," "Timing," and "Turbo Timing" to fine-tune the ESC to your specific boat and motor combination.
- Utilize the data logging function with the OTA Bluetooth module to analyze performance data and identify areas for improvement or potential issues.
- Regularly check for and install firmware updates to benefit from the latest features and bug fixes.
10. Warranty and Support
For warranty claims or technical support, please contact your authorized HOBBYWING dealer or visit the official HOBBYWING website. Keep your proof of purchase for any warranty-related inquiries.