HOBBYWING UBEC-10A-V2-Car

Contents

HOBBYWING UBEC-10A-V2-Car Instruction Manual

Model: UBEC-10A-V2-Car

Brand: HOBBYWING

1. Introduction

The HOBBYWING UBEC-10A-V2-Car is a high-efficiency external switching-mode BEC (Battery Eliminator Circuit) designed specifically for RC car models. In many RC car applications, particularly with climbing cars and engineering trailer heads, peripheral devices require higher current and voltage than what a standard electric controller's built-in BEC can provide. This UBEC is engineered to meet these demands, offering a stable and adjustable power supply to your RC model's electronic components.

HOBBYWING UBEC-10A-V2-Car product overview
Figure 1: HOBBYWING UBEC-10A-V2-Car product overview, showing the main unit with input/output wires and a ferrite ring.

2. Specifications

Below are the detailed technical specifications for the UBEC-10A-V2-Car:

Feature Detail
Model HW-UBEC-10A-V2-Car
Input Voltage 2-6S Lithium Battery (LiPo)
Output Voltage 6.0V / 7.4V / 8.4V (Adjustable in 3 levels)
Output Current 10A (Continuous), 15A (Instantaneous)
Dimensions (L*W*H) 45 * 20 * 16.2 mm
Weight 34g (including cable)
Material Composite Material
For Vehicle Type Cars
Recommended Age 14+ years
Close-up of UBEC voltage selection
Figure 2: Close-up view of the HOBBYWING UBEC-10A-V2-Car, highlighting the voltage selection pins (6.0V, 7.4V, 8.4V) and input/output labels.

3. Package Contents

The package typically includes the following items:

  • 1x HOBBYWING UBEC-10A-V2-Car Unit
  • 1x Jumper Cap (for voltage selection)
  • 1x Waterproof Switch

4. Setup

Careful wiring is essential for proper operation and to prevent damage to your RC model. Refer to the wiring diagram below for guidance.

Detailed wiring diagram for UBEC-10A-V2-Car
Figure 3: Detailed wiring diagram for the HOBBYWING UBEC-10A-V2-Car, illustrating connections for Output, Jumper cap, Jumper pin, Waterproof Switch, and 2-6s LiPo Input.

4.1. Output Voltage Selection

The UBEC-10A-V2-Car offers three output voltage options: 6.0V, 7.4V, and 8.4V. You can select the desired voltage using the included jumper cap on the jumper pins located on the UBEC unit.

  • 6.0V: Place the jumper cap on the two pins closest to the '6.0V' label.
  • 7.4V: Place the jumper cap on the two middle pins, aligned with the '7.4V' label.
  • 8.4V: Place the jumper cap on the two pins closest to the '8.4V' label.

Important: Ensure the jumper cap is securely placed on the correct pins for your desired voltage before connecting power. Incorrect voltage can damage your receiver or servos.

4.2. Wiring Connections

  1. Input (2-6S LiPo): Connect the red and black input wires of the UBEC to your main battery pack (2-6S LiPo). Ensure correct polarity (red to positive, black to negative).
  2. Output: Connect the output cable of the UBEC to the BEC input port on your RC receiver or other peripheral devices requiring power.
  3. Waterproof Switch: Connect the waterproof switch to the designated switch port on the UBEC. This switch controls the power to the UBEC's output.

Warning: Always double-check all connections for correct polarity and secure fit before applying power to avoid short circuits or damage to components.

5. Operating Instructions

Once the UBEC is correctly installed and wired:

  1. Ensure your main battery is connected to the UBEC input.
  2. Turn on the waterproof switch connected to the UBEC. This will supply power to your receiver and connected peripherals at the selected output voltage.
  3. Verify that your receiver and servos are functioning correctly.
  4. To power off, simply turn off the waterproof switch.

The UBEC provides a stable and regulated power supply, allowing your RC model's electronics to operate reliably even under high current draw from multiple servos or other accessories.

6. Maintenance

To ensure the longevity and optimal performance of your HOBBYWING UBEC-10A-V2-Car, follow these simple maintenance guidelines:

  • Keep Clean: Regularly inspect the UBEC for dirt, dust, or debris. Clean gently with a soft, dry brush or compressed air.
  • Avoid Moisture: While the switch is waterproof, the main UBEC unit should be protected from excessive moisture and water exposure.
  • Check Connections: Periodically inspect all wiring connections for signs of wear, corrosion, or looseness. Ensure all plugs are securely seated.
  • Temperature: Operate the UBEC within its specified temperature range. Ensure adequate airflow around the unit if installed in an enclosed space.
  • Storage: When not in use for extended periods, disconnect the UBEC from the battery and store it in a dry, cool place.

7. Troubleshooting

If you encounter issues with your UBEC, consider the following common troubleshooting steps:

  • No Power to Receiver/Servos:
    • Check if the main battery is charged and properly connected to the UBEC input.
    • Ensure the waterproof switch is in the 'ON' position.
    • Verify that the UBEC output cable is securely connected to the receiver.
    • Inspect all wires for damage or breaks.
  • Erratic Servo Behavior:
    • Confirm that the correct output voltage is selected via the jumper cap for your receiver and servos.
    • Check for loose connections or interference.
    • Ensure the UBEC is not overloaded (e.g., too many high-current servos).
  • UBEC Overheating:
    • Ensure the UBEC has sufficient airflow.
    • Reduce the load on the UBEC if possible, or consider if a higher current UBEC is needed for your setup.

8. User Tips

  • Always match the UBEC output voltage to the maximum voltage rating of your receiver and servos to prevent damage.
  • Consider using a voltage checker to confirm the output voltage after setting the jumper cap.
  • Mount the UBEC in a location that allows for good air circulation to aid in cooling.
  • Secure all wiring to prevent accidental disconnections or entanglement with moving parts.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official HOBBYWING website or contact your authorized dealer. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.