Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, setup, and troubleshooting of the Raise G-FT-RZ-64 16 Pin CANBUS Adaptor. This adaptor is designed to facilitate the integration of an aftermarket Android car radio with the existing CANBUS system in compatible Toyota and Lexus RX350 vehicles, ensuring proper functionality of features like steering wheel controls and vehicle information display.

Please read this manual thoroughly before beginning the installation to ensure correct setup and safe operation.

2. Safety Information

• Always disconnect the vehicle's negative battery terminal before performing any electrical work to prevent short circuits or electrical shock.
• Ensure all connections are secure and properly insulated to avoid damage to the device or vehicle's electrical system.
• If you are unsure about any part of the installation process, consult a qualified professional.
• Do not use excessive force when removing or installing vehicle trim panels to prevent damage.

3. Package Contents

Before installation, verify that all components are present:

• Raise G-FT-RZ-64 CANBUS Adaptor (16 Pin)
• Wiring Harness
• Power Cable
• (Optional, depending on kit) GPS antenna
• (Optional, depending on kit) USB cable
• (Optional, depending on kit) Rear camera cable
• Basic installation tools (not included)

4. Installation Guide

The following steps outline the general installation process. Refer to your vehicle's specific service manual for detailed instructions on removing trim panels and accessing wiring. Visual diagrams are typically provided with the product to aid in these steps.

4.1. Pre-Installation Preparation

• Ensure all required components (head unit, fascia frame, power/CANBUS cable, GPS antenna, USB cable, rear camera cable if applicable, and basic installation tools) are prepared.
• Disconnect the vehicle's negative battery terminal to prevent electrical hazards.

4.2. Remove the Original Center Console

• Use a plastic trim tool to carefully detach the decorative panel surrounding the center console. Work slowly to avoid damaging clips.
• Unscrew any mounting screws securing the original head unit.
• Disconnect the factory wiring harness and the antenna connector from the original unit.
• Store all removed parts safely to prevent loss or damage.

4.3. Android Head Unit Installation & Functional Verification

Wiring Connection:

• Connect the power harness to the vehicle's original factory connector.
• If your vehicle has a CANBUS system, ensure the G-FT-RZ-64 decoder is correctly installed and configured.
• Verify that the ACC (ignition) and constant power (B+) connections are secure and properly matched.

Accessory Installation:

• Install the GPS antenna in an optimal location for signal reception (e.g., on the dashboard, away from obstructions).
• Connect the USB extension cable for additional connectivity.
• If applicable, connect the rear-view camera video input cable and reverse trigger wire according to the wiring diagram provided with your head unit.

System Testing:

• Reconnect the vehicle's negative battery terminal and switch the ignition to ACC/ON.
• Confirm that the head unit powers on properly.
• Test all major functions:
  • Steering wheel control integration
  • Reverse camera display
  • Radio reception
  • Bluetooth connectivity
• Ensure proper operation of all features for a fully functional system before final assembly.

4.4. Final Installation & Securing

• Position the head unit into the fascia frame and secure it using the designated mounting screws. Ensure proper alignment and stability.
• Align the retaining clips with their corresponding slots and carefully press the trim panel back into place. Ensure the panel fits flush against the dashboard.
• Organize the wiring harness using cable ties to bundle and secure any excess cables. Route wiring neatly, away from moving parts and ventilation ducts, to prevent interference and potential noise.

5. CANBUS Setup Guide

Proper configuration of the CANBUS decoder is essential for full functionality.

5.1. Enter the Settings Menu

• Power on the head unit and navigate to Settings > Factory Settings.
• You may be prompted for a password. Common default passwords include 8888, 1234, or 0000, depending on the device manufacturer.

5.2. Select the Correct CANBUS Type

• In the CAN Type or Protocol section, choose the vehicle brand and model that precisely matches your car's protocol.
• Important: Selecting the incorrect protocol can lead to issues such as:
  • Steering wheel controls not functioning
  • Absence of sound from parking sensors
  • Other system malfunctions

5.3. Save and Restart

• Once the correct protocol is selected, save the settings.
• Restart the head unit for the changes to take effect.

5.4. Function Test

After rebooting, verify the following features:

• Steering wheel controls
• Reverse camera and parking sensor sound
• Automatic headlight reminders (if supported by vehicle)
• Door status display (if supported by vehicle)
• Air conditioning information display (if supported by vehicle)

6. Troubleshooting

This section addresses common issues you might encounter during or after installation.

7. Specifications

8. User Tips

Based on common user experiences, here are some tips for optimal use:

• Double-Check Compatibility: Always confirm that the CANBUS adaptor model (G-FT-RZ-64) is specifically listed as compatible with your exact vehicle year, make, and model (e.g., Toyota/Lexus RX350).
• Firm Connections: Ensure all wiring harness connections are fully seated and locked into place. Loose connections are a common cause of intermittent issues.
• Test Before Reassembly: Before fully reassembling your dashboard, perform a comprehensive function test of your new head unit and CANBUS features. This saves time if adjustments are needed.
• Consult Online Resources: If you encounter unusual issues, online forums or communities dedicated to car audio installation for your specific vehicle might offer additional insights or solutions.

9. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your retailer or the manufacturer at the time of purchase. For technical support or further assistance, please contact the seller or manufacturer directly.

A detailed user manual in PDF format may also be available for download: View User Manual (PDF)