Iradio UV-98 PLUS

Contents

Iradio UV-98 PLUS 10W Walkie Talkie Instruction Manual

Model: UV-98 PLUS

Brand: Irado

Introduction

Thank you for choosing the Irado UV-98 PLUS 10W Walkie Talkie. This device is a full-band HF Ham Radio featuring USB, LSB, CW, CB, LW, MW, SW, and SSB reception, along with Cross Band Repeater capabilities. It boasts a 2.4-inch large color screen, 1024 memory channels, and three VFO channels, offering versatile communication options. Please read this manual carefully to ensure proper operation and to maximize your device's performance.

Safety Precautions

To prevent fire, personal injury, equipment damage, or other accidents, please observe the following precautions:

  • Do not use the equipment in inflammable and explosive environments (e.g., gas, dust, smoke). Turn off the equipment when refueling or parking at gas stations.
  • Do not place the equipment in dusty, wet, or splashed places, or on uneven surfaces.
  • Use this equipment away from interference sources (e.g., TV, computer, distribution cabinet).
  • Do not transmit while charging.
  • Do not expose the device to direct sunlight for extended periods or place it near heating devices.
  • If the equipment emits an abnormal odor, turn it off immediately. After ensuring safety, send it to the nearest maintenance site for inspection.
  • Do not modify or adjust this equipment for any reason.
  • Always obey local laws and regulations.

Disclaimer: The customer bears all responsibility for equipment failure or accidents caused by violation of these precautions.

Package Contents

Upon unboxing, please verify that all the following accessories are included and in good condition:

No.ItemQuantity
1Radio1
2Antenna1
3Li-ion Battery1
4Charger1
5Belt Clip1
6User Manual1
7Guarantee Card1

If any items are missing or damaged, please contact your local distributor.

Iradio UV-98 PLUS Walkie Talkie and its accessories including base charger, charger, battery, Type-C charger cable, clip, manual, antenna, and lanyard.
Figure 1: Package Contents

Product Overview

Diagram of the Irado UV-98 PLUS Walkie Talkie with labeled parts.
Figure 2: Front and Side View of the Walkie Talkie

Key Components:

  1. Antenna
  2. PTT (Push-to-Talk) Button
  3. Side-key 1
  4. Side-key 2
  5. Battery
  6. SW/MW/LW FM antenna (Channel knob)
  7. ON/OFF volume
  8. Indicator Light
  9. Alarm Button
  10. Display screen
  11. Keypad
  12. MIC
  13. Speaker
  14. Earpiece jack
  15. Type C charging port/programmable jack
Detailed diagram of the Irado UV-98 PLUS Walkie Talkie with labeled components including antenna, alarm button, ON/OFF volume knob, indicator, launch key, side keys, menu function area, Type-C charger, and keypad.
Figure 3: Detailed Component Diagram

Specifications

ParameterValue
Product ModelUV-98 PLUS
Frequency Range (Radio)FM: 64-108MHz, SW: 2.3-30MHz, MW: 520-1710KHz, LW: 153-279KHz
Frequency Range (RX)18-620MHz, 840-1000MHz (AM/FM/SSB)
Frequency Range (TX)18-64MHz, 136-520MHz
Storage Channels1024 Channels + 3 VFO Channels
Channel Spacing (W/N)Analog: 25KHz/12.5KHz, Digital: 12.5K
Operating Voltage7.4V DC
Battery Capacity2400mAh
Charging MethodType-C / Dock Charging
Dimension (Antenna not included)149 × 64 × 37 mm
Weight307g
Frequency Stability±2.5ppm
Working Temperature-20℃ ~ +60℃
Output Power5W-10W
Waterproof / Water-ResistantNo
MaterialPlastic
Maximum Range5km-10km
Detailed Parameters table for Irado UV-98 PLUS Walkie Talkie.
Figure 4: Detailed Specifications

Setup

1. Battery Installation

  1. Align the battery with the battery compartment on the back of the radio.
  2. Slide the battery into place until it clicks securely.

2. Antenna Attachment

  1. Screw the antenna clockwise onto the antenna connector at the top of the radio until it is finger-tight.
  2. Ensure the antenna is compatible with the frequency band you intend to use.
27MHz CB Telescopic Antenna with SMA-Female connector.
Figure 5: Example of a 27MHz CB Telescopic Antenna
Detachable nut for antenna, allowing pairing with donut antennas for enhanced penetration and stability.
Figure 6: Detachable Nut for Donut Antenna
Donut AM Antenna (red) and Donut SW Antenna (blue) for enhanced signal reception.
Figure 7: Donut AM and SW Antennas

3. Charging the Battery

The Irado UV-98 PLUS supports two charging methods: a base charger and a Type-C charger.

  1. Using the Base Charger: Place the radio with the battery installed into the charging cradle. Ensure the charging contacts align. The indicator light will show charging status (red for charging, green for fully charged).
  2. Using the Type-C Charger: Connect the Type-C cable to the charging port on the side of the radio and plug the other end into a compatible USB power source.
Multiple charging methods for the Irado UV-98 PLUS, showing both base charger and Type-C direct charging.
Figure 8: Charging Methods

4. Programming

This walkie-talkie requires a dedicated Type-C interface Programming Cable (provided by the manufacturer) to connect to a computer. Channel programming is performed using the UV-98 PLUS frequency writing software. A regular mobile phone data cable or regular write frequency cable cannot establish a communication connection. If you cannot find the frequency writing software, please contact customer support.

Operating Instructions

1. Power On/Off

Rotate the ON/OFF volume knob clockwise to power on the device. Rotate counter-clockwise until it clicks to power off.

2. Display and Interface

The device features a 2.4" TFT HD Large Colorscreen Display. It supports up to 1024 named memory channels and three VFO channels. The display shows frequency, channel alias, mode (FM, W, CTC, H), and other status indicators.

2.4 inch TFT HD Large Colorscreen Display showing VOX and S9+ field strength indicator.
Figure 9: Large Colorscreen Display

3. Keypad Functions

The keypad allows for various operations and settings adjustments:

  • PTT (Push-to-Talk): Transmit or Exit.
  • Alert Key: Definable long press and short press functions.
  • Side Key 1 & 2: Definable long press and short press functions. Can be customized for Multi-PTT (PTT-2 for Side Key 1, PTT-3 for Side Key 2).
  • OK: Short press to confirm or enter menu.
  • #: Short press to switch between channel frequency/number/alias. Long press to lock the keypad.
  • *: Short press to switch working mode (VFO/channel/zone). Long press to jump to transmit frequency input menu.
  • 0-9: Numeric input.
  • Up/Down Arrows: Navigate menus, adjust values.

4. Customizing Key Shortcuts

You can customize the functions of the side keys and keyboard according to your preferences and needs.

  1. Press the Menu button.
  2. Navigate to and select Key Define.
  3. Choose the key (e.g., Side Key 1 S for short press, Side Key 1 L for long press) you wish to customize.
  4. Select the desired function from the list (e.g., Power Switch, Scanning, VOX, FM Radio).
Video 1: Demonstration of customizing key shortcuts.

5. One-Click Frequency Measurement

This function allows for fast frequency matching.

  1. Ensure the correct frequency band is selected in the settings (see 'Switching Frequency Ranges' below).
  2. Press the shortcut button that has been set as the frequency matching function to start one-click frequency matching.
Video 2: Demonstration of one-click frequency measurement.

6. FM Radio

The device can store 128 FM channels.

  1. Enter the menu, find FM Radio.
  2. You can save the current FM frequency and edit its name.
  3. In FM radio mode, long press the "#" button to switch between SW/MW/LW bands.
  4. Short press the "#" button in SW/MW/LW mode to switch between CW/LSB/USB modes.
  5. Short press the "*" button to move the cursor and change frequency and other settings as needed.
Video 3: Demonstration of FM Radio functions.

7. Cross Band Repeater

The Cross Band Repeater mode allows the radio to transmit signals further and achieve a longer operating range, making communication more flexible. It can relay across different frequency bands (UV cross-band) or within the same frequency band (UU same-frequency inter-transfer).

  1. Enter the settings and enable UV Repeater.
  2. Set a frequency point for each of the A frequency and B frequency in the UHF/VHF band.
  3. Enter Key Define to customize a button for Cross Band Repeater switch.
Diagram showing two walkie talkies communicating via cross-band repeater mode, illustrating U trans U and U trans V scenarios.
Figure 10: Cross-Band Repeater Mode
Video 4: Demonstration of Cross Band Repeater function.

8. Switching Frequency Ranges

The device has three working ranges: 64-620MHz, 18-64MHz, and 840-1000MHz. These ranges cannot work simultaneously. You must select the desired frequency band in the settings and replace the antenna accordingly.

  1. Press the Menu button.
  2. Navigate to Basic Settings.
  3. Scroll down to Work Range.
  4. Select the desired frequency range (e.g., 18-64MHz).
  5. Confirm your selection. The device will restart.
  6. Important: Always replace the antenna with one compatible with the selected frequency band to avoid damage and ensure proper transmission/reception.
Video 5: Demonstration of switching frequency ranges.

9. DTMF Functions

The device supports DTMF encoding, transmission, and decoding.

  • DTMF Encoding Input & Transmission: In standby mode, long press the appropriate key to enter the DTMF input interface. Use the numeric keypad to enter DTMF codes. Short press Side Key 2 to delete the last DTMF digit. Press the PTT key to initiate a call; the device will send the DTMF code after a preset delay.
  • DTMF Decoding: When the device receives a signal and DTMF decoding is enabled, the screen will display the received DTMF code.
  • DTMF Transmission in Analog Mode: During analog transmission, pressing a key on the keypad will send the corresponding DTMF code.
  • DTMF Remote Monitoring: Set a DTMF monitoring code for the device and enable 'Accept Remote Control'. Another radio can send the same DTMF code to this device. Upon receiving and successfully decoding the DTMF code, the device will automatically transmit for 60 seconds, enabling remote monitoring.

10. Other Features

  • Triple Frequency Standby: Allows monitoring of three frequencies simultaneously.
  • S9+ Field Strength Indicator: Real-time display of field strength values.
  • NOAA Weather Forecast Channels: 11 channels available (United States only).
  • Aviation AM Signals: Receives aviation AM signals (108-136MHz).
  • Power-Saving Mode: Gradually deepens power saving ratio over time when enabled.
  • Frequency Scan & Channel Scan: Functions for scanning frequencies and channels.
  • Spectrum Scanning: Function for spectrum analysis.
  • VOX (Voice Activated Transmit): Enables/disables voice-activated transmission.
  • Monitoring Function: Allows monitoring of signals.
  • Emergency Alarm: Activates alarm mode.
  • Editable Single-Tone Transmission: The 1750 Hz tone can wake up the repeater.
  • Startup Logo & Prompt: Customizable.
  • DTMF Remote Stun/Kill/Wake: Allows remote control of the device's operational status.

Maintenance

1. Cleaning

Regularly clean the radio's exterior with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure no moisture enters the device.

2. Battery Care

  • Charge the battery fully before first use.
  • Avoid overcharging or completely draining the battery to prolong its lifespan.
  • Store the battery in a cool, dry place when not in use for extended periods.

Troubleshooting

  • Abnormal Odor: If the equipment emits an abnormal odor, turn it off immediately and send it to a maintenance site.
  • No Transmission/Keypad Operation (Stunned): If the device is stunned via DTMF remote control, it cannot transmit or operate the keypad. It can still receive signals. A wake code is required to restore it.
  • Device Unusable (Killed): If the device is killed via DTMF remote control, it becomes unusable until it receives a wake code. Ensure a wake code is set, or the device cannot be restored.
  • Intermittent Calls / Large Frequency Offset: If receiving signals from devices with a large frequency offset, calls may be intermittent. Increase the neighboring channel suppression threshold in settings.
  • Sharp Sound in SSB Mode: When using Single Sideband (USB or LSB) demodulation and encountering sharp sound, lower the BFO (Beat Frequency Oscillator) frequency. If the sound is too deep, increase the BFO frequency.
  • Mismatched Antennas: Always use an antenna compatible with the selected frequency band to avoid damage and ensure proper transmission/reception.

User Tips

  • Dedicated Programming Cable: The UV-98 PLUS requires a specific Type-C programming cable from the manufacturer for channel programming. Generic USB cables or other write frequency cables will not work.
  • Antenna Matching: When switching between frequency ranges (e.g., 18-64MHz, 64-620MHz, 840-1000MHz), always ensure you attach an antenna specifically designed for that range. For example, a 27MHz CB antenna for the 27MHz band.
  • SSB Mode: To adjust SSB settings, navigate through the menu to find the relevant options for LSB/USB. Refer to the 'Operating Instructions' section for switching between modes.
  • Battery Life: Users have noted good battery longevity with this device.

Warranty & Support

For warranty information, technical support, or to access the full user manual in PDF format, please refer to the official documentation provided by the manufacturer or contact your point of purchase. A PDF version of the user manual is available here.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.