FMS MJX 7303

Contents

MJX 7303 Hyper Go 1/7 RC Drift Car Instruction Manual

Model: MJX 7303 | Brand: FMS

Disclaimer: Not suitable for children under 36 months.

1. Introduction

The MJX 7303 Hyper Go is a 1/7 scale brushless 4WD remote control drift car designed for rally racing enthusiasts. This manual provides essential information for setting up, operating, and maintaining your RC vehicle to ensure optimal performance and longevity.

MJX 7303 Hyper Go RC Drift Car in action on a dirt track
The MJX 7303 Hyper Go RC Drift Car demonstrating its capabilities on a dirt track.

2. Package Contents

Please verify that all items are present in your package:

  • MJX 7303 Hyper Go RC Drift Car (Ready-to-Go)
  • Remote Controller
  • Operating Instructions (this manual)
  • USB Cable
  • One set of road tires (additional gift)

NOTE: Battery and charger are NOT included and must be prepared separately.

3. Setup

3.1 Battery Installation

The MJX 7303 features an adjustable battery compartment to accommodate various battery sizes. Ensure your battery fits within the dimensions of approximately 14.5 cm x 5.2 cm.

  1. Open the battery compartment cover on the chassis.
  2. Insert your compatible battery, ensuring correct polarity.
  3. Secure the battery and close the compartment cover.
Internal view of the RC car chassis showing the metal chassis and adjustable battery compartment
Internal view of the chassis, highlighting the metal construction and the adjustable battery compartment (approx. 14.5cm x 5.2cm).

3.2 Remote Controller Setup

The remote controller supports MODE1 and MODE2. Ensure batteries are installed in the remote controller (not included).

Detailed view of the remote controller with labeled functions
Remote controller with labeled functions for precise control.

Familiarize yourself with the controller functions:

  • CH1: ST (Steering): Controls left and right movement.
  • CH2: TH (Throttle): Controls forward and reverse speed.
  • LED (Light Switch Control): Toggles the car's lights.
  • ST.REV (Steering Reverse): Reverses the steering direction.
  • TH.TRIM (Throttle Neutral Adjustment): Adjusts the throttle's neutral position.
  • ST.TRIM (Steering Trim): Adjusts the steering's center position.
  • ST.D/R (Steering Dual Rate): Adjusts the maximum steering angle.
  • TH.D/R (Throttle Dual Rate): Adjusts the maximum throttle output.
  • Power Switch: Turns the remote controller on/off.

4. Operating Instructions

4.1 First Run

  1. Ensure the car's battery is fully charged and installed.
  2. Turn on the remote controller first, then the car.
  3. Wait for the car and controller to bind (indicator lights will confirm).
  4. Test steering and throttle response at low speeds in a safe, open area.
  5. Adjust ST.TRIM and TH.TRIM if the car does not drive straight or stops at neutral throttle.

4.2 Driving Tips

  • The G3C Gyroscope assists in maintaining control during drifts and high-speed maneuvers. Experiment with its settings if adjustable.
  • Utilize the 4WD system for excellent traction and control on various surfaces.
  • The car is equipped with a full car linkage light set, which can be controlled via the LED switch on the remote.
  • Practice gentle throttle and steering inputs to master drifting techniques.
MJX 7303 RC Drift Car with full car linkage light set
The MJX 7303 features a full car linkage light set for enhanced realism.

5. Maintenance

Regular maintenance will extend the life and performance of your RC car.

5.1 General Care

  • After each use, clean the car to remove dirt, dust, and debris.
  • Inspect all screws and fasteners for tightness.
  • Check for any damaged or worn parts.

5.2 Component Specific Maintenance

  • Drivetrain: The car features metal CVDs, full car powder metallurgy gears, and three sealed metal differentials. Periodically inspect these components for wear and ensure they are free of obstructions.
  • Suspension: The metal oil pressure shock absorbers should be checked for leaks and proper function. Ensure all full car bearings are clean and lubricated.
  • Electronics: The receiver is housed in a waterproof box, providing protection from splashes. However, avoid submerging the car. Keep all electronic connections clean and dry.
  • Chassis: The metal chassis and metal transmission shafts provide durability. Inspect for bends or damage after impacts.
  • Tires: The car comes with two sets of tires. Use the appropriate set for your driving surface. Regularly check for wear and tear.
Exploded view of the drivetrain and suspension components
Detailed view of the drivetrain and suspension, highlighting durable metal components.
Components including metal CVD, full car powder metallurgy gears, three sealed metal differentials
Key internal components: metal CVDs, powder metallurgy gears, and sealed metal differentials.
Metal transmission shafts and metal chassis
The robust metal chassis and transmission shafts ensure durability.

6. Troubleshooting

This section addresses common issues you might encounter with your RC car.

6.1 Car Not Responding

  • Check Battery: Ensure the car's battery is charged and properly connected.
  • Remote Controller Power: Verify the remote controller has fresh batteries and is turned on.
  • Binding: Confirm that the car and remote controller are properly bound. Turn both off, then turn on the controller first, followed by the car.
  • Power Switches: Ensure both the car and controller power switches are in the 'ON' position.

6.2 Steering Problems

  • Steering Trim (ST.TRIM): Adjust the steering trim on the remote controller to center the wheels.
  • Steering Reverse (ST.REV): If steering is reversed, use the ST.REV switch on the controller.
  • Obstructions: Check for any debris or damage preventing the wheels from turning freely.
  • Servo Function: Ensure the 35kg metal gear servo is functioning correctly and not jammed.

6.3 Motor/Throttle Issues

  • Throttle Trim (TH.TRIM): Adjust the throttle trim if the car moves slightly when the throttle is neutral.
  • ESC Connection: Ensure the 120A Hall-effect brushless ESC is properly connected to the motor and receiver.
  • Motor Inspection: Check the 3974 2500 KV brushless motor for any visible damage or debris.

7. Specifications

FeatureSpecification
Model NumberMJX 7303
Brand NameFMS
Scale1:7
Dimensions632 x 290 x 237 mm
MaterialMetal, Plastic, PVC
State of AssemblyReady-to-Go
Control Channels6 channels
Controller ModeMODE2, MODE1
Remote ControlYes
MotorBrushless 3974, 2500 KV
ESC120A Hall-effect Brushless
Servo35kg Metal Gear
GyroscopeG3C Gyroscope
CertificationCE
Recommended Age14+ years
OriginMainland China
Package Weight9.8 kg
Package Dimensions84 x 34 x 28 cm
Overview of the MJX 7303 RC Drift Car with key components highlighted
Key components of the MJX 7303: Brushless motor, ESC, servo, G3C Gyroscope, waterproof receiver box, and included tire sets.
Brushless motor (3974, 2500 KV) and 120A Hall-effect brushless ESC
The powerful 3974 2500 KV brushless motor and 120A Hall-effect brushless ESC.
Close-up of the G3C Gyroscope
The G3C Gyroscope, essential for drift control and stability.

8. Warranty and Support

For specific warranty information and support, please refer to the seller's policies or contact the seller directly. General return and refund policies can be found via the seller's platform.

9. User Tips

No specific user tips were available from provided reviews or Q&A content. Always ensure your battery is fully charged before use for optimal performance and run time. Regularly clean your RC car, especially after driving in dusty or dirty conditions, to prevent wear on moving parts.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.