Equity 30402 Extra-Large Red LED Electric Alarm Clock User Manual

Introduction

Thank you for purchasing the Equity 30402 Extra-Large Red LED Electric Alarm Clock. This clock features a clear 3-inch red LED display with adjustable brightness, a powerful alarm, and an 8-minute snooze function. Designed for ease of use, it includes a corded electric power source with a 9V battery backup to ensure timekeeping during power outages. This manual provides detailed instructions for setup, operation, and maintenance to help you get the most out of your new alarm clock.

Safety Information

Read all instructions before operating the clock.
Do not expose the unit to extreme temperatures, direct sunlight, or high humidity.
Use only the specified power adapter.
Keep the clock away from water or other liquids.
Do not attempt to disassemble or repair the unit yourself. Refer all servicing to qualified personnel.
Dispose of batteries properly according to local regulations.

Package Contents

Equity 30402 Alarm Clock Unit
AC Power Adapter
User Manual (this document)

Product Overview

Familiarize yourself with the various parts and controls of your alarm clock:

Front view of the Equity 30402 alarm clock with large red LED display and control buttons.

Figure 1: Front View of the Alarm Clock

Angled view of the Equity 30402 alarm clock, showing the top snooze button and rear alarm switch.

Figure 2: Angled View with Top and Rear Controls

Control Buttons and Indicators:

HOUR Button: Adjusts the hour for time and alarm settings.
MINUTE Button: Adjusts the minute for time and alarm settings.
HIGH/LOW Button: Toggles display brightness between high and low.
SET TIME Button: Enters time setting mode.
SET ALARM Button: Enters alarm setting mode.
RUN TIME Button: Exits setting modes and returns to normal time display.
SNOOZE Button (Top): Activates the snooze function when the alarm sounds.
ALARM ON/OFF Switch (Rear): Turns the alarm function on or off.
PM Indicator: Lights up when the time is PM.
ALARM Indicator: Lights up when the alarm is set to ON.

Setup

Power Connection: Plug the AC power adapter into the DC jack on the back of the clock, then plug the adapter into a standard wall outlet. The display will light up.
Battery Backup Installation: Open the battery compartment cover on the bottom of the clock. Insert one new 9V battery (not included), observing the correct polarity (+ and -). Close the battery compartment cover. This battery provides backup power during power outages, preserving your time and alarm settings.
Initial Time Setting: The clock may display a default time or 12:00. Proceed to the "Operating Instructions" section to set the correct time.

Operating Instructions

Setting the Current Time

Press the SET TIME button once. The hour digits will begin to flash.
Press the HOUR button repeatedly to advance the hour. Hold the button down for faster adjustment. Observe the PM indicator for correct AM/PM setting.
Press the MINUTE button repeatedly to advance the minute. Hold the button down for faster adjustment.
Once the desired time is set, press the RUN TIME button to save and exit the time setting mode. The clock will return to normal time display.

Setting the Alarm Time

Press the SET ALARM button once. The alarm hour digits will begin to flash.
Press the HOUR button repeatedly to set the desired alarm hour. Observe the PM indicator for correct AM/PM setting.
Press the MINUTE button repeatedly to set the desired alarm minute.
Once the desired alarm time is set, press the RUN TIME button to save and exit the alarm setting mode. The clock will return to normal time display.

Activating/Deactivating the Alarm

To activate the alarm, slide the ALARM ON/OFF switch (located on the back of the clock) to the "ON" position. The ALARM indicator light on the display will illuminate.
To deactivate the alarm, slide the ALARM ON/OFF switch to the "OFF" position. The ALARM indicator light will turn off.

Snooze Function

When the alarm sounds, press the large SNOOZE button on the top of the clock. The alarm will temporarily stop and sound again after approximately 8 minutes.
To turn off the alarm completely after it sounds, slide the ALARM ON/OFF switch to the "OFF" position, or press any other button (HOUR, MINUTE, SET TIME, SET ALARM, RUN TIME).

Adjusting Display Brightness

Press the HIGH/LOW button to toggle the display brightness between high and low settings. Choose the setting that is most comfortable for your viewing environment.

Maintenance

Cleaning: Wipe the clock with a soft, dry cloth. Do not use abrasive cleaners or solvents.
Battery Replacement: Replace the 9V backup battery annually or when you notice that the time is not retained during power outages. Ensure the clock is connected to AC power when replacing the battery to avoid losing current time settings.

Troubleshooting

Problem	Possible Cause	Solution
Clock display is blank.	No AC power; power outage.	Ensure AC adapter is securely plugged into the clock and wall outlet. Check if the outlet is working. If there's a power outage, the display will be blank but time will be kept by the backup battery.
Alarm does not sound.	Alarm is not activated; alarm volume is too low (if applicable); incorrect alarm time set.	Ensure the ALARM ON/OFF switch is in the "ON" position and the ALARM indicator is lit. Verify the alarm time is set correctly (AM/PM).
Time/Alarm settings are lost after power outage.	Backup battery is dead or not installed.	Install a fresh 9V battery or replace the existing one.
Display is too bright/dim.	Brightness setting needs adjustment.	Press the HIGH/LOW button to cycle through brightness settings.

Specifications

Feature	Detail
Display Type	3-inch Red LED
Brightness Settings	High / Low
Power Source	Corded Electric (AC Adapter)
Battery Backup	1 x 9V Battery (not included)
Snooze Duration	8 minutes
Dimensions (Approx.)	Not specified in provided data.
Weight (Approx.)	Not specified in provided data.

User Tips

For optimal visibility, place the clock where the display is not directly facing a strong light source.
Consider setting the display brightness to 'Low' for nighttime use to avoid excessive light in a dark room.
Always ensure the 9V backup battery is fresh to prevent loss of settings during unexpected power interruptions.
When setting the time or alarm, holding down the HOUR or MINUTE button will speed up the adjustment process.

Warranty and Support

This product is covered by a standard manufacturer's warranty. For specific warranty details, claims, or technical support, please refer to the documentation provided at the point of purchase or contact the seller directly. Keep your purchase receipt as proof of purchase.

	Equity 3-Inch Jumbo LED Alarm Clock Model 30402 User Manual and Features User manual and features for the Equity 3-Inch Jumbo LED Alarm Clock, Model 30402. Includes setup instructions, operation guide, safety warnings, warranty information, and FCC statement.
	Equity NightVision LCD Alarm Clock 30330 User Manual and Features Detailed guide for the Equity NightVision LCD Alarm Clock (Model 30330) by La Crosse Technology, covering setup, features, care, warranty, and FCC compliance.
	Equity 31302 LCD Travel Alarm Clock: Instructions and Features This document provides instructions for the Equity 31302 LCD Travel Alarm Clock, detailing its features, setup, alarm functions, countdown timer, and warranty information.
	Equity Alarm Clock 13014 Clock Hands Replacement Guide A step-by-step guide from iFixit on how to replace the clock hands on the Equity Alarm Clock model 13014. This guide covers disassembly, hand removal, and reassembly instructions.
	Equity Analog Quartz Alarm Clock 20090/20091 User Manual & Warranty User manual and warranty information for the Equity Analog Quartz Alarm Clock models 20090 and 20091. Includes setup, operation, specifications, and care instructions.
	Equity 0.9-inch Blue LED Alarm Clock User Manual User guide for the Equity 0.9-inch Blue LED Alarm Clock, model 75903v2. Includes setup instructions, alarm settings, snooze function, battery backup, power requirements, and warranty information.

Equity 30402