Estardyn NV3007

Contents

Estardyn 1.68-inch TFT LCD Screen User Manual

Model: NV3007

1. Introduction

This manual provides detailed instructions for the Estardyn 1.68-inch TFT LCD screen, model NV3007. This compact display module features a 142x428 resolution, full view angle, and utilizes a 4-wire SPI interface for communication. It is designed for various embedded applications requiring a small, colorful display.

Front and back view of the 1.68-inch TFT LCD module

Figure 1: Estardyn 1.68-inch TFT LCD Module (Front and Back)

2. Specifications

The following table outlines the key technical specifications of the Estardyn 1.68-inch TFT LCD module:

Product parameters and pin definition diagram

Figure 2: Product Parameters and Pin Definition

Table 1: Technical Specifications
Feature Description
Size 1.68 inch
Resolution 142*428
Driver IC NV3007
Interface Type 4-wire SPI
Display Color Colorful
Power Supply 2.8V-3.3V
Operating Temperature -20°C ~ 70°C
Linking Method COG
Screen Size (mm) 16.3 x 44.96 x 2.23
Module Size (mm) 24.77 x 48.51 x 3.56
Display Size (mm) 13.16 x 39.68
Detailed mechanical drawing with dimensions

Figure 3: Mechanical Dimensions

3. Pin Definition

The module features an 8-pin interface for power and SPI communication. Refer to Figure 2 for a visual representation of the pins.

Table 2: Pinout Description
Pin No. Symbol Description
1 GND Ground
2 VCC Power Supply (2.8V-3.3V)
3 SCL SPI Clock Line
4 SDA SPI Data Line
5 RES Reset Pin
6 DC Data/Command Selection Pin
7 CS Chip Select Pin
8 BL Backlight Control Pin

4. Setup Instructions

Follow these steps to properly set up your Estardyn 1.68-inch TFT LCD module:

  1. Power Connection: Connect the VCC pin to a 2.8V-3.3V power supply and the GND pin to the ground of your microcontroller or development board. Ensure the power supply is stable and within the specified voltage range.
  2. SPI Interface Connection:
    • Connect SCL (SPI Clock) to your microcontroller's SPI clock pin.
    • Connect SDA (SPI Data) to your microcontroller's SPI MOSI (Master Out Slave In) pin.
    • Connect CS (Chip Select) to a digital output pin on your microcontroller.
    • Connect DC (Data/Command) to a digital output pin on your microcontroller. This pin determines whether the data being sent is a command or display data.
    • Connect RES (Reset) to a digital output pin on your microcontroller. This pin is used to reset the display controller.
  3. Backlight Connection: Connect the BL pin to a suitable power source or a digital output pin if you wish to control the backlight programmatically.
  4. Physical Mounting: Secure the module to your project enclosure or PCB using appropriate standoffs or mounting hardware. Avoid applying excessive pressure to the display area.
Angled view of the display module

Figure 4: Angled View of the Display Module

5. Operating Instructions

Operating the NV3007 TFT LCD requires a microcontroller and appropriate software (firmware) to send commands and data via the SPI interface.

  1. Initialization: After power-up, the display controller (NV3007) needs to be initialized. This typically involves a sequence of commands sent via SPI to configure display parameters such as resolution, pixel format, and display orientation. Refer to the NV3007 datasheet for the exact initialization sequence.
  2. Sending Commands and Data:
    • To send a command, set the DC pin LOW, then transmit the command byte(s) via SPI.
    • To send display data (pixel data), set the DC pin HIGH, then transmit the data byte(s) via SPI.
    • The CS pin should be asserted (LOW) during the entire SPI transaction for the display module.
  3. Displaying Graphics and Text: Once initialized, you can send pixel data to the display's frame buffer. Libraries for common microcontrollers (e.g., Arduino, ESP32) often simplify this process, providing functions for drawing shapes, text, and images.
  4. Full View Angle: The display offers a full view angle, meaning the image quality remains consistent across a wide range of viewing positions.

6. Maintenance

To ensure the longevity and optimal performance of your TFT LCD module, observe the following maintenance guidelines:

  • Handle with Care: The display panel is fragile. Avoid dropping, bending, or applying excessive force to the module.
  • Static Discharge: Always handle the module in an ESD-safe environment to prevent damage from electrostatic discharge.
  • Cleaning: Use a soft, lint-free cloth, lightly dampened with distilled water or an LCD cleaning solution, to gently wipe the display surface. Avoid abrasive materials or harsh chemicals.
  • Environmental Conditions: Operate and store the module within the specified temperature range of -20°C to 70°C. Avoid exposure to direct sunlight, high humidity, or extreme temperature fluctuations.
  • Power Supply: Ensure a stable and clean power supply within the 2.8V-3.3V range. Voltage fluctuations can affect display performance and potentially damage the module.

7. Troubleshooting

If you encounter issues with your Estardyn 1.68-inch TFT LCD module, consider the following troubleshooting steps:

  • No Display/Blank Screen:
    • Verify that VCC and GND connections are correct and the power supply is active and within the 2.8V-3.3V range.
    • Check all SPI connections (SCL, SDA, CS, DC, RES) for continuity and correct wiring.
    • Ensure the backlight (BL) pin is properly powered or controlled.
    • Confirm that the microcontroller's initialization code for the NV3007 driver IC is correctly implemented and executed.
  • Incorrect or Garbled Display:
    • Check the SPI communication protocol (mode, clock speed) in your firmware.
    • Verify that the data/command (DC) pin is toggled correctly when sending commands versus data.
    • Ensure the resolution settings (142x428) in your initialization code match the display's specifications.
    • Confirm the pixel data format (e.g., RGB565) and byte order are correct.
  • Flickering Display:
    • Check the stability of your power supply. Add decoupling capacitors near the VCC pin if necessary.
    • Ensure your SPI clock speed is not excessively high for your microcontroller or wiring setup.

8. User Tips

Based on common practices for similar display modules, here are some tips for optimal use:

  • Software Libraries: For ease of development, consider using existing open-source libraries for TFT displays and the NV3007 driver IC with popular microcontrollers like Arduino or ESP32. These libraries often abstract away low-level SPI communication.
  • Power Consumption: While compact, TFT displays consume more power than OLEDs. Factor this into your power budget, especially for battery-powered applications.
  • Backlight Control: If your application requires adjustable brightness, consider using Pulse Width Modulation (PWM) on the BL pin to control the backlight intensity.
  • Orientation: The display can typically be configured for different orientations (portrait or landscape) through software commands. Experiment with these settings to find the best fit for your project.

9. Warranty & Support

For technical support, driver code examples, or inquiries regarding your Estardyn 1.68-inch TFT LCD module, please contact your vendor or the manufacturer directly. Keep your purchase receipt for any warranty claims.

© 2024 Estardyn. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.