QIACHIP SM-028-0548

Contents

QIACHIP SM-028 eWeLink WiFi Smart Switch Module User Manual

Model: SM-028-0548 | Brand: QIACHIP

1. Introduction

The SM-028 is a Wi-Fi+BLE dual-protocol module developed by eWeLink. It integrates a highly integrated wireless radio frequency chip and minimal peripheral devices. Operating in the 2.4GHz frequency band, this module supports 802.11 b/g/n wireless standards and requires a single 3.3V power supply. Its versatile design allows for flexible application in various consumer products, including smart home systems, smart appliances, and intelligent lighting control.

Front view of the QIACHIP SM-028 module with eWeLink logo and channel information
Figure 1: Front view of the SM-028 module, highlighting eWeLink compatibility and channel options (1/2/4 channel, high-level signal output).

2. Product Features

  • Built-in low-power 32-bit CPU, capable of functioning as an application processor.
  • Supports 802.11 b/g/n wireless standards.
  • Multiple security modes: WPS, WEP, WPA /WPA2 Personal /WPA2 Enterprise /WPA3.
  • PWM control functionality.
  • Supports timer operations.
  • Enables remote Wi-Fi control.
  • Supports compatible pairing mode and Bluetooth pairing (Bluetooth 5.0).
  • Over-The-Air (OTA) firmware upgrade capability.
  • Supports 2.4G intelligent light control.
  • Local area network (LAN) control.
  • Compatibility with smart speakers such as Amazon Alexa and Google Assistant.

3. Specifications

3.1. Rated Parameters

Conditions: VDD = 3.3V ± 10%, GND = 0V; tested at room temperature of 25°C.

ParameterValue
ModelSM-028
Hardware InterfacePWM, IIC, GPIO
Operating Voltage3.0V~3.3V
Operating CurrentAverage: ≈45mA, Maximum: 350mA
Operating Temperature0°C~45°C
Storage Environment (Temperature)-10°C~75°C
Storage Environment (Relative Humidity)20%RH~80%RH
Wireless Network TypeWiFi: STA/AP/STA+AP, Bluetooth: Bluetooth 5.0
Security MechanismWPS, WEP, WPA /WPA2 Personal /WPA2 Enterprise /WPA3
Encryption TypeWEP64/WEP128/TKIP/AES 128/192/256
Firmware UpgradeOTA remote upgrade

3.2. Wi-Fi Parameters

Conditions: VDD = 3.3V ± 10%, GND = 0V; tested at a room temperature of 25°C.

ParameterValue
Wireless StandardIEEE 802.11b/g/n
Frequency Range (WiFi)2412-2482Mhz
Frequency Range (Bluetooth)2.400GHz to 2.4835GHz
Transmit Power (802.11b)19±1dBm (@11Mbps)
Transmit Power (802.11g)16±1dBm (@54Mbps)
Transmit Power (802.11n)16±1dBm (@HT20,MCS7)
Receive Sensitivity (802.11b)-92 dBm (@11Mbps, CCK)
Receive Sensitivity (802.11g)-76 dBm (@54Mbps, OFDM)
Receive Sensitivity (802.11n)-72 dBm (MCS7)
Antenna TypePCB Antenna

4. Setup and Wiring

4.1. Module Pin Definition

The SM-028 module features several pins for power, ground, control signals, and button inputs. Understanding these pins is crucial for proper integration and operation.

Front view of the SM-028 module showing pin labels L, A, B, G, R
Figure 2: Front view of the SM-028 module with visible pin labels.
Back view of the SM-028 module showing pin labels 3V3, GND, 22, 17, C, W
Figure 3: Back view of the SM-028 module with visible pin labels.
  • 3V3: Module power supply input (DC 3.3V).
  • GND: Module negative pole (Ground).
  • 22: Relay 3 switch control signal output. This pin is high-level effective. It is low by default and goes high when the relay is turned on.
  • 17: Relay 2 switch control signal output. This pin is high-level effective. It is low by default and goes high when the relay is turned on.
  • C: Relay 1 switch control signal output. This pin is high-level effective. It is low by default and goes high when the relay is turned on.
  • W: Relay 4 switch control signal output. This pin is high-level effective. It is low by default and goes high when the relay is turned on.
  • R: Button control 4 input. This pin is high by default and low-level effective. Pulling it low for more than 5 seconds initiates pairing mode.
  • G: Device status indicator light output. This pin is high-level effective. Connect a 1K current-limiting resistor in series externally to ground.
  • B: Button control 1 input. This pin is high by default and low-level effective. Pulling it low for more than 5 seconds initiates pairing mode.
  • A: Button control 2 input. This pin is high by default and low-level effective. Pulling it low for more than 5 seconds initiates pairing mode.
  • L: Button control 3 input. This pin is high by default and low-level effective. Pulling it low for more than 5 seconds initiates pairing mode.

4.2. Wiring Diagrams

Refer to the following diagrams for typical wiring configurations of the SM-028 module for 1, 2, and 4 channel setups.

Detailed wiring diagram for 1-channel, 2-channel, and 4-channel configurations of the SM-028 module
Figure 4: Comprehensive wiring diagram for various channel configurations.
Simplified wiring diagram for the SM-028 module
Figure 5: Simplified wiring diagram for basic connections.

5. Operating Instructions

5.1. Switch Control

  • eWeLink App Control: When the SM-028 module is connected to the internet, you can control its switch functions remotely via the eWeLink mobile application.
  • Local Area Network (LAN) Control: If your mobile device and the SM-028 module are on the same local network, you can control the module's switches directly through the eWeLink app without requiring an internet connection.
  • 2.4G Remote Control: The SM-028 module supports 2.4G intelligent light remote control. Its switches can be controlled by a compatible and learned 2.4G remote controller.

5.2. Pairing Mode

To enter pairing mode, pull any of the button control input pins (R, B, A, or L) low for more than 5 seconds. This will allow the module to be discovered and paired with the eWeLink app or a 2.4G remote controller.

6. Maintenance

The SM-028 module is designed for reliable operation with minimal maintenance. Ensure the module is installed in a dry environment, free from excessive dust or moisture. Avoid exposing the module to extreme temperatures outside its specified operating range (0°C~45°C). Regularly check connections for security and integrity. For cleaning, use a dry, soft cloth. Do not use liquid cleaners or solvents.

7. Troubleshooting

  • Module not responding: Verify the 3.3V power supply is correctly connected and within the specified voltage range. Check all wiring connections for continuity and proper contact.
  • Unable to connect to Wi-Fi: Ensure your Wi-Fi network is 2.4GHz and that the module is within range. Re-enter pairing mode and attempt to connect via the eWeLink app. Check Wi-Fi credentials.
  • Remote control not working: Ensure the 2.4G remote controller is properly paired with the module. Check the remote's battery if applicable.
  • Indicator light (G pin) not functioning: Verify the 1K current-limiting resistor is correctly installed in series with the G pin and ground. Check the LED itself.

8. User Tips

No specific user tips were available from reviews or Q&A for this product. General advice for smart modules includes:

  • Always ensure stable power supply within the specified voltage range to prevent unexpected behavior.
  • For optimal Wi-Fi performance, place the module within a reasonable distance from your router.
  • Familiarize yourself with the eWeLink app's features for scheduling, automation, and voice control integration.
  • When integrating into custom projects, consider proper heat dissipation, especially if the module is enclosed.

9. Warranty and Support

For warranty information and technical support, please refer to the official QIACHIP website or contact your retailer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.