AVATTO GW70-MQTT

Contents

AVATTO Zigbee 3.0 USB Dongle Plus Instruction Manual

Model: GW70-MQTT | Brand: AVATTO

1. Introduction

The AVATTO Zigbee 3.0 USB Dongle Plus (Model: GW70-MQTT) is a versatile USB stick designed to act as a universal Zigbee gateway. It enables local control of your Zigbee sub-devices through popular smart home platforms like Home Assistant and Zigbee2MQTT, eliminating the need for multiple brand-specific Zigbee hubs. This dongle features a high-gain detachable antenna for enhanced signal transmission and supports up to 128 sub-devices.

AVATTO Zigbee 3.0 USB Dongle Plus
Figure 1: AVATTO Zigbee 3.0 USB Dongle Plus

2. Key Features

  • Universal Zigbee Gateway: Compatible with Home Assistant, Zigbee2MQTT, and other open-source platforms.
  • High-Gain Detachable Antenna: 20dBm (max), 5dBi antenna for extended signal range and reliable communication.
  • Aluminum Housing: Effectively reduces signal interference from peripherals.
  • Software Flow Control: Improves communication reliability when data congestion occurs.
  • TI CC2652P Chip: Based on the Texas Instruments CC2652P chip for robust performance.
  • Rotatable Antenna: SMA interface external rotatable antenna for optimal positioning.
  • Router Functionality: Can be flashed with router firmware to extend the Zigbee network range.
  • Sub-device Support: Supports up to 128 sub-devices.
Key Features of AVATTO Zigbee Dongle
Figure 2: Overview of product features

3. Setup and Installation

This section guides you through setting up your AVATTO Zigbee 3.0 USB Dongle Plus with Home Assistant. You will need a smart host running Home Assistant (e.g., Home Assistant Green/Yellow, Raspberry Pi, Self-developed HA box, VM/NAS).

Video 1: Installation and Configuration Guide for Home Assistant

3.1 Physical Connection

  1. Connect the AVATTO Zigbee 3.0 USB Dongle Plus to a USB port on your computer or smart host where Home Assistant is running.
  2. Ensure the rotatable antenna is positioned for optimal signal reception.
Connecting the Zigbee Dongle
Figure 3: AVATTO Zigbee Dongle connected to a host device.

3.2 Home Assistant Integration Options

There are two primary ways to integrate the dongle with Home Assistant:

  • Way 1: Use Zigbee2MQTT integration (Recommended for advanced users or those with specific device support needs).
  • Way 2: Use ZHA (Zigbee Home Automation) integration (Built-in and generally simpler for basic setups).

3.2.1 Way 1: Zigbee2MQTT Integration

  1. Install Zigbee2MQTT Add-on:
    • In Home Assistant, navigate to Settings > Add-ons.
    • Click Add-on Store (bottom right).
    • Click the three dots in the top right corner and select Repositories.
    • Add the repository URL: https://github.com/zigbee2mqtt/hassio-zigbee2mqtt and click Add.
    • Close the repositories window. Search for "Zigbee2MQTT" and install the add-on.
  2. Find the Device Path:
    • Go to Settings > System > Hardware.
    • Click the three dots in the top right corner and select All hardware.
    • Locate the entry for "Silicon Labs CP2102 USB to UART Bridge Controller" (or similar) and copy its device path (e.g., /dev/ttyUSB0).
  3. Configure Zigbee2MQTT:
    • Go back to Settings > Add-ons > Zigbee2MQTT.
    • Navigate to the Configuration tab.
    • Under the serial section, find the port entry and paste the copied device path. Ensure there is a space before the path (e.g., port: /dev/ttyUSB0).
    • Save the configuration and start the Zigbee2MQTT add-on.

3.2.2 Way 2: ZHA Integration

  1. Configure ZHA:
    • In Home Assistant, navigate to Settings > Devices & services.
    • Click Add integration (bottom right).
    • Search for "ZHA" and select Zigbee Home Automation.
    • Select the serial port corresponding to your Zigbee USB dongle (e.g., /dev/ttyUSB0 - CP2102 USB to UART Bridge Controller).
    • Click Submit.
    • Choose to Erase network settings and create a new network.
    • Assign the device to an area (e.g., "Study") or create a new one, then click Finish.

4. Operation

4.1 Adding Zigbee Sub-devices

Once your Zigbee coordinator (either via Zigbee2MQTT or ZHA) is set up in Home Assistant, you can start adding your Zigbee sub-devices.

  1. For Zigbee2MQTT:
    • Go to the Zigbee2MQTT interface (usually accessible via the Home Assistant sidebar if enabled).
    • Look for an option like "Allow new devices to join" or "Permit join" and activate it.
    • Put your Zigbee sub-device into pairing mode (refer to your sub-device's manual for specific instructions). The device should be discovered and added automatically.
  2. For ZHA:
    • Go to Settings > Devices & services > Zigbee Home Automation.
    • Click on the Devices tab.
    • Click Add device via this device.
    • Put your Zigbee sub-device into pairing mode. The device should be discovered and added.
Zigbee Sub-device Support
Figure 4: The dongle supports up to 128 sub-devices.

4.2 Using as a Zigbee Router

The Dongle Plus comes pre-flashed with coordinator firmware. However, it can also be flashed with router firmware to extend the range of your existing Zigbee network. This is useful for creating a more robust mesh network, especially in larger homes or areas with signal obstacles.

Zigbee Router Functionality
Figure 5: Diagram illustrating the dongle's use as a Zigbee router to extend network coverage.

For instructions on flashing router firmware, please refer to the official Zigbee2MQTT documentation or relevant community resources, as this process may vary and requires specific tools and knowledge.

5. Maintenance

  • Keep Firmware Updated: Regularly check for firmware updates for your dongle, especially if using Zigbee2MQTT or ZHA, to ensure optimal performance and compatibility with new devices.
  • Physical Care: Keep the dongle in a dry environment and avoid extreme temperatures. The aluminum housing helps with heat dissipation and interference reduction.
  • Antenna Positioning: Periodically adjust the rotatable antenna to ensure the best possible signal strength and network coverage.

6. Troubleshooting

  • Device Not Detected:
    • Ensure the dongle is securely plugged into a USB port.
    • Verify that the correct device path is configured in Home Assistant (e.g., /dev/ttyUSB0).
    • Restart Home Assistant or the host system.
  • Sub-devices Not Pairing:
    • Ensure the dongle's integration (Zigbee2MQTT or ZHA) is in "permit join" or "add device" mode.
    • Check that the sub-device is in its correct pairing mode.
    • Move the sub-device closer to the dongle during pairing.
    • Ensure the sub-device is compatible with Zigbee 3.0.
  • Signal Issues:
    • Adjust the rotatable antenna for better signal.
    • Consider adding another dongle flashed with router firmware to extend network coverage.
    • Avoid placing the dongle near sources of interference (e.g., Wi-Fi routers, USB 3.0 ports without shielding).
  • Firmware Files: If you need specific firmware files for flashing, refer to the official Zigbee2MQTT GitHub repository or the manufacturer's support page.

7. Specifications

AttributeValue
Brand NameAVATTO
Model NumberGW70-MQTT
NameZigbee 3.0 USB Dongle Plus
TypeZigbee Gateway Hub
OriginMainland China
CertificationCE
Features+20dBm Signal enhancement
Type 1USB plug
Type 2Communication Distance 400M (Without obstruction)
Type 3Thread, Zigbee 3.0, Bluetooth 5.2 LE
Type 4Supports 128 sub-device
Type 5Working temperature -10°C~40°C
Type 6Compatible with multiple connection platforms
SupportHome Assistant Zigbee2MQTT/Raspbian Ubuntu Macos
Wireless Communication Frequency2.4GHz-2.48GHz
Communication Distance400M (Without obstruction)
Signal strength (dbm)18.6 (Instrument testing)
Working temperature-10°C~40°C
Dimension (Dongle)73mm x 24.5mm x 11mm (2.87in x 0.965in x 0.433in)
Dimension (Antenna)108.5mm (4.27in)
Package Length11 cm
Package Width3 cm
Package Height1 cm
Package Weight0.029 kg
Product Dimensions and Parameters
Figure 6: Detailed product dimensions and technical parameters.

8. User Tips

  • Firmware Management: For optimal performance and compatibility, ensure your dongle's firmware is up-to-date. Firmware files are often available on the official Zigbee2MQTT GitHub page or the manufacturer's support resources.
  • Network Stability: If experiencing connectivity issues, consider the placement of the dongle. Using a USB extension cable can sometimes help mitigate interference from the host device's USB 3.0 ports.

9. Warranty and Support

  • Warranty: All products come with a 1-year warranty from the store.
  • Customer Support: For any inquiries or assistance, please contact customer support. Emails are typically answered within 24 hours.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.