Cisco WS-C2960X-48TD-L

Contents

Cisco Catalyst WS-C2960X-48TD-L Network Switch User Manual

Model: WS-C2960X-48TD-L | Brand: Cisco

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your Cisco Catalyst WS-C2960X-48TD-L Network Switch. The Catalyst 2960 Series Switches are designed to provide robust services for various network environments, including branches, conventional office workspaces, infrastructure networks, and medium-sized campus deployments. This specific model offers advanced features for efficient and secure network management.

2. Product Overview

The Cisco Catalyst WS-C2960X-48TD-L is a 48-port Gigabit Ethernet switch with 2 x 10G SFP+ uplinks, operating on LAN Base software. It is a managed switch offering a range of features for professional audio equipment and general network infrastructure.

2.1 Key Features

  • Ports: 48 Gigabit Ethernet ports
  • Uplinks: 2 x 10G SFP+ ports
  • Transmission Rate: 216Gbps
  • Switch Capacity: 216Gbps
  • Functions: LACP, POE, QoS, SNMP, Stackable, VLAN Support
  • Communication Mode: Full-Duplex & Half-Duplex
  • RAM: 512 MB Installed Size
  • Default Primary AC Power Supply: PWR-C5-125WAC
  • Device Type: Switch - 48 Ports - Managed

2.2 Product Views

Cisco Catalyst 2960-X switch with modular power supplies
Figure 1: Cisco Catalyst 2960-X switch with modular power supplies.
Front view of the Cisco Catalyst 2960-X 48-port switch
Figure 2: Front view of the Cisco Catalyst 2960-X 48-port switch, showing Ethernet and SFP+ ports.
Rear view of the Cisco Catalyst 2960-X switch
Figure 3: Rear view of the Cisco Catalyst 2960-X switch, showing power input and ventilation.

3. Specifications

Attribute Value
Model Number WS-C2960X-48TD-L
Product Name 48 Port Switch
Device Type Switch - 48 Ports - Managed
Ports 48 x 10/100/1000 Gigabit Ethernet, 2 x 10G SFP+
PoE Ports 48 Port Support PoE
Transmission Rate 216Gbps
Switch Capacity 216Gbps
Stacking Bandwidth 128 Gbps
RAM Installed Size 512 MB
Dimensions (H x W x D) 1.7 x 17.6 x 16.1 inches (approx. 4.3 x 44.7 x 40.9 cm)
Functions LACP, POE, QoS, SNMP, Stackable, VLAN Support
Communication Mode Full-Duplex & Half-Duplex
Origin Mainland China
Warranty 1 year

4. Setup Instructions

Follow these steps to properly set up your Cisco Catalyst WS-C2960X-48TD-L switch.

4.1 Unpacking and Inspection

  1. Carefully unpack the switch and all accessories from the shipping carton.
  2. Verify that all items listed in the packing list are present and undamaged.
  3. Inspect the switch for any physical damage. If any damage is found, contact your vendor immediately.

4.2 Mounting the Switch

The switch is designed for rack-mounting. Ensure you have a standard 19-inch equipment rack available.

  1. Attach the provided rack-mount brackets to the sides of the switch using the screws supplied.
  2. Secure the switch into the equipment rack using appropriate rack screws. Ensure the switch is level and securely fastened.

4.3 Connecting Power

The switch uses a PWR-C5-125WAC as its default primary AC power supply.

  1. Connect one end of the AC power cord to the power connector on the rear of the switch.
  2. Connect the other end of the AC power cord to a grounded electrical outlet.
  3. Verify that the power LED on the front panel illuminates, indicating the switch is receiving power.
Detailed view of the rear panel of the switch, showing power supply and module slots
Figure 4: Rear panel detail, illustrating power input and potential module slots.

4.4 Connecting Network Cables

The switch features 48 Gigabit Ethernet ports and 2 x 10G SFP+ uplink ports.

  1. Connect your network devices (computers, servers, access points, etc.) to the 48 Gigabit Ethernet ports using standard Ethernet cables (RJ-45).
  2. For high-speed connections to other network infrastructure (e.g., core switches, routers), use appropriate SFP+ transceivers and fiber optic cables in the 10G SFP+ uplink ports.
  3. Ensure all cable connections are secure.
Close-up of the front panel of a Cisco Catalyst switch, showing ports and indicator LEDs
Figure 5: Front panel detail, illustrating Ethernet and SFP+ ports with indicator LEDs.

5. Operating Instructions

Once the switch is physically installed and powered on, it begins its boot sequence. The switch operates with a LAN Base image, providing a comprehensive set of features for network management.

5.1 Power On and Initial Boot

  • After connecting power, the switch will automatically power on.
  • Observe the system LED indicators on the front panel. A solid green System LED indicates successful boot-up.
  • The switch will load its operating system and configuration. This process may take a few minutes.

5.2 Basic Connectivity

  • Once booted, connected devices should establish network links. The port status LEDs will indicate link activity and speed.
  • For initial configuration, connect a console cable to the console port and use a terminal emulator, or connect a management workstation to any Ethernet port and access the switch via its default IP address (refer to Cisco documentation for default IP and login credentials).

5.3 Advanced Features and Configuration

The Cisco Catalyst WS-C2960X-48TD-L supports various advanced networking functions:

  • Link Aggregation Control Protocol (LACP): For bundling multiple physical links into a single logical link to increase bandwidth and provide redundancy.
  • Power over Ethernet (PoE): To power compatible devices (e.g., IP phones, wireless access points) directly through the Ethernet cable.
  • Quality of Service (QoS): To prioritize network traffic for critical applications.
  • Simple Network Management Protocol (SNMP): For network monitoring and management.
  • Stackable: Allows multiple switches to operate as a single logical unit, simplifying management and increasing scalability.
  • VLAN Support: For segmenting the network into logical broadcast domains to improve security and performance.

Detailed configuration of these features requires knowledge of Cisco IOS commands. Refer to the official Cisco documentation for comprehensive configuration guides.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your network switch.

6.1 Environmental Considerations

  • Ensure the switch is operated within its specified temperature and humidity ranges.
  • Maintain adequate airflow around the switch. Do not block ventilation openings.
  • Keep the environment free from dust and debris, which can accumulate and cause overheating.

6.2 Cleaning

  • Periodically clean the exterior of the switch with a soft, dry, lint-free cloth.
  • Do not use liquid or aerosol cleaners directly on the switch.
  • Use compressed air to gently clear dust from ventilation grilles.

6.3 Firmware and Software Updates

  • Regularly check the Cisco support website for the latest software and firmware updates.
  • Applying updates can improve performance, add new features, and address security vulnerabilities.
  • Always follow Cisco's recommended procedures for software upgrades to avoid service interruptions.

7. Troubleshooting

This section provides basic troubleshooting steps for common issues. For more complex problems, consult the official Cisco documentation or contact technical support.

7.1 Power Issues

  • No Power: Check if the power cord is securely connected to both the switch and the power outlet. Verify the power outlet is functional.
  • System LED Off: If the System LED is off after power connection, ensure the power supply is correctly seated and functional.

7.2 Connectivity Issues

  • No Link Light: Ensure the Ethernet cable is securely connected to both the switch port and the connected device. Try a different cable or port. Verify the connected device is powered on and functioning correctly.
  • Slow Performance: Check for network congestion. Verify duplex and speed settings on both the switch port and the connected device. Ensure proper VLAN configuration if applicable.

7.3 Indicator Lights

Refer to the switch's front panel LEDs to diagnose issues:

  • System LED: Indicates overall system status (e.g., green for normal operation, amber for fault).
  • Port Status LEDs: Indicate link status, activity, and PoE status. Consult the official documentation for detailed LED interpretations.

8. User Tips

No specific user tips were available from customer reviews or Q&A for this product. For best practices and advanced configurations, always refer to the official Cisco documentation and community forums.

9. Warranty and Support

9.1 Warranty Information

This product comes with a 1-year warranty from the date of purchase. Please retain your proof of purchase for warranty claims.

9.2 Technical Support

For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact your vendor or refer to the official Cisco support resources available on their website.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.